A user‐resource planning framework for offshore recreational artificial reefs

Abstract

Artificial reefs have been used extensively in coastal waters to attract and enhance recreational fishery resources. In the United States, they have been traditionally built from “materials of opportunity”; using limited budgets. This paper explores some past planning philosophies and presents a recent artificial reef deployment case that demonstrates a lack of sensitivity to local and regional recreational demand. A systems framework is developed to guide future planning efforts in artificial reef development. The framework is intended to integrate previously fragmented knowledge and to demonstrate the interdisciplinary nature of artificial reef planning. Emphasis is given to advance planning, user dimensions, and the integral issue of reef access.     

Evaluating the energy performance of a SUV hybrid electric vehicle

This paper analyzes the energetic performance of the hybrid Lexus RX 400h, through on-board measurements. Several speed profiles were analyzed, for three driving types, successive stop and go cycles, three speed profiles, crossing an electronic toll collection booth, and a roundabout. In stop and go situations the internal combustion engine did not work (the torque needed to impulse the vehicle in the stop and go situations was only supported by the electric engines), as well as in the situations of constant low speeds (50 or 60 km h^?1). The auxiliary support given by the electric engines in the accelerations, as well as the importance of the energy regeneration system on the batteries’ load recovery is also demonstrated. When compared with similar conventional vehicles, the Lexus RX 400h has lower combined energy consumption between 1.2% and 60%.     

A regional railroad network optimization model for coal transportation

A regional railroad network is presented to evaluate the system's response to increased coal traffic. An optimal, multimodal, coal-shipping pattern is developed for the study region to minimize total costs and to efficiently use the existing network. A two-stage, general model allocates resources among demands and then assigns flows to the network according to efficiency criteria. The model is sufficiently general to permit modification for specific needs, assumptions and data. Government agencies and industries can apply the model in resource allocation decisions and transportation policy analysis.     

A risk model for the operation of container vessels

Commercial shipping of containerized goods involves certain risks for human safety and environment. In order to actively manage these risks, they must be identified, analyzed, modeled, and quantified. This requires a systematical analysis of design and operation of container vessels. Within the EU-funded research project SAFEDOR, a Formal Safety Assessment has been applied to establish the current safety level of generic container ships and to identify potential cost-effective risk control options. This paper describes a structured approach to develop the underlying high-level risk model. It is structured as risk contribution tree consisting of a series of fault trees and event trees for the major accident categories. Statistical analysis of casualty data is used to estimate the probability of occurrence. Finally, the summation overall individual risk contributions yields the current risk pro file for the operation of container vessels is presented as FN-curve.     

Circumventing the weight-versus-footprint tradeoffs in vehicle fuel economy regulation

China, Japan, and the European Union use weight-based fuel economy standards, whereas the US Department of Transportation favors footprint-based standards. In this paper we offer a way of reconciling these approaches. Weight-based standards tend to focus regulatory incentives on technology rather than downsizing, but they provide no incentive for weight reduction. Footprint-based standards, by contrast, motivate vehicle manufacturers to reduce weight without reducing footprint, but only to the extent that they are also motivated to increase footprint without increasing weight. Neither approach discriminates between beneficial and detrimental weight-changing strategies. However, the tradeoffs between weight and footprint can be circumvented by employing a weight-based standard, which does not create weight-changing incentives, in combination with complementary regulatory measures that would be focused specifically and exclusively on motivating beneficial weight reduction strategies.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Correcting injection pressure maladjustments to reduce NOX emissions by marine diesel engines

Emissions from the exhausts of marine diesel engines comprises several different gases including NO_X. These are currently regulated at the international level under Regulation 13 of ANNEX VI of MARPOL 73/78, but this regulation only applies to new engines and is based on bench tests, for only a single engine designated the “parent engine”. Here, the need to take measurements from across their whole range and once in operation on board a vessel is examined. This would not only improve assessment of new equipment against the current regulation, but would also detect defects in the functioning of the engine.