热插拔控制器在汽车电路中的应用

介绍一种用于汽车这种具有强电源干扰环境的热插拔控制器。它既能够为微控制器提供干净稳定的电源,又能保证在自身模块更换时不对蓄电池电源造成干扰。     

工程机械融资租赁的风险控制

为了更好地控制工程机械融资租赁的风险,针对工程机械融资租赁这一特殊行业的特点,通过工作总结和文献研究,对融资租赁中的风险加以分析、评价,提出了相应的风险控制方法,对工程机械融资租赁的风险控制具有指导意义.     

葑溪大桥施工控制

为了保证葑溪大桥的施工安全和质量,根据预应力混凝土斜拉桥悬臂浇筑和支架现浇非对称施工特点,建立施工控制计算模型,探讨影响主梁线形及斜拉索索力的因素,并制定相应控制措施,对主梁线形、内力、索力、牵索挂篮应力和变形进行有效监控.施工控制结果表明:成桥状态下,主桥轴线实测标高、桥梁应力状态、成桥索力均满足设计要求,挂篮在施工过程中的应力状态及变形情况与试验变化趋势基本一致.     

爆破振动对宋家湾隧道施工的影响

为评价在生产常规作业阶段爆破施工方式对隧道结构的影响,对宋家湾隧道爆破振动进行监测,以获取主振频率,最终以频率和振动速度2个指标评估隧道爆破作业振动效应.本次爆破的最大振动速度为3.1 cm/s,主振频率范围为27.34～70.31 Hz,最大振动速度远小于国家标准.可知对隧道支护结构影响有限频率范围为27.34～70.31 Hz,远高于隧道的自振频率(一般在3～9 Hz范围内),不会出现共振放大现象.     

拧紧扳手凸轮轴自动变位装置研发与设计

文章介绍了拧紧扳手凸轮轴自动变位装置的工作原理和制造目标。简述了实现拧紧扳手凸轮轴自动变位装置制造目标的结构:凸轮轴自动变位模块、电气控制模块、误差调整模块等。给出了拧紧扳手凸轮轴自动变位装置发展趋势,对汽车发动机自动化装配生产线的研发具有重要的参考价值。     

Study of an optimized gas strut layout to improve opening and closing quality

The most important factor in gas strut design is determining an optimized layout. If the layout is not optimized, vehicle operators will have a suboptimal experience when opening and closing the tailgate. A poor layout of the gas struts causes operators to work excessively when they open/close the tailgate, and vehicle owners will incur additional expenses due to deterioration in the body quality of the vehicle. Thus, an optimized gas strut layout is very important, even if it does not seem interesting. This paper describes the tailgate operation process and focuses on determining an optimized gas strut layout for opening/closing the tailgate easily.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

隔板缝隙对抗性消声器声学性能影响的试验研究

采用试验方法研究隔板缝隙对消声器声学性能的影响,结果表明,隔板缝隙对扩张式消声器影响不大,但将提高共振式消声器共振频率.分析其原因是由于隔板缝隙的存在,增大了等效旁支管的总横截面,因而减小了其声质量,提高了系统的固有频率;而加长隔板翻边的长度,使旁支管的长度变长,声质量增大,共振频率降低,因而可部分抵消缝隙的负面影响.     

微型汽车零部件设计对整车电控标定影响的分析

结合自主标定的某微型汽车产品项目,阐述了其油泵总成、发电机、触媒、真空助力器、传动系等主要零部件的结构特点.研究了这些关键零部件对整车冷起动标定、高温热起动标定、排放标定、怠速稳定性标定、OBD标定等的影响,并通过实例总结了微型汽车整车标定的特点.     

发动机VVT叶片式相位器响应速度影响因素相关性分析

利用AMESim建立了发动机可变凸轮相位器响应速度数值仿真模型,结合试验设计和相关性分析,验证了仿真模型的可靠性并研究了相位器的各个关键参数对其响应速度的影响机理.研究发现:对相位器响应速度影响显著的一次因素为叶片力臂、叶片厚度、预加载荷;在全平面工况内,二次因素对相位器响应速度的影响呈复杂的非线性;叶片力臂较大时,叶...