酚醛树脂复合材料在轨道交通车辆上的应用

介绍了酚醛树脂复合材料试制的主要原材料、主要设备及仪器、试制流程及测试标准。详细阐述了酚醛树脂复合材料的氧指数、燃烧性能、机械性能、低密度等性能。分析了热压时间、热压温度及生产工艺对酚醛树脂复合材料性能的影响。试验证明,酚醛树脂产品的性能较为优良:热压时间控制在1.1~1.4 h时,复合材料的表面性能良好;热压温度为80~100℃时,可以得到表面质量细腻均匀的复合材料;适当调整生产工艺,可以提高酚醛树脂的产品质量、降低生产成本。     

单片机在无线通讯中的应用

采用可工作于433 MHz频段的无线射频收发模块n RF9E5,通过内嵌8051单片机C语言编程,实现多通道、短距离的数据传输。并在近距离范围内验证了所设计的无线通讯模式的可靠性和准确性。     

GSM-R中跨SGSN更新时源SGSN域名解析数据的智能生成方案设计

源SGSN域名解析数据是GSM-R网络编号方案数据中重要的需跨局制作的一类数据。由RAI编码构造生成,在跨SGSN路由区更新时,存储于DNS中,以解析源SGSN的IP地址。全路400多条G网线路,错综复杂的基站引用关系,导致数据复杂多样。针对该情况,利用聚类分析和关联规则分析算法,研究源SGSN解析数据的智能生成方案,提高数据的全面性、准确性,从而有效保障GSM-R分组域应用业务的正常运转。     

基于PANDA软件的框架网坐标解算可靠性分析

应用高精度定位解算软件PANDA对框架网进行解算,并与Bernese解进行比较,探讨不同软件模型下框架网的点位坐标解算方法及其精度;通过算例表明PANDA软件的定位解算结果与Bernese的解有较好的一致性,表明PANDA软件有较高的可靠性和稳定性。     

乘用车进气系统核心试验方法解读

通过对进气系统在零部件系统试验、发动机台架试验、整车试验上的核心试验方法解读,让读者对进气系统有更全面的认识。     

Simulation of mixed gas formation for a spray-wall complex guided LPG direct injection engine

To obtain an ultralean air-fuel ratio and to reduce engine-out NOX and HC emissions induced by the richer mixture near the spark plug, a spray and wall complex guided combustion system has been developed by utilizing the fuel characteristics of LPG. The new combustion system configuration is optimized by using a commercial CFD code, FIRE V2013, and the reliability of the system has been experimentally demonstrated by Plane Laser-Induced Fluorescence (PLIF). The mixture formation in the new combustion system under part load (2,000 rpm) is numerically simulated. With an injection timing of 40°CA BTDC, the LPG spray which is injected from two upper holes, reaches the ignition point, and the other part of the LPG spray which is injected from the bottom hole, is directed to the ignition point through the vertical vortices at the same time. At the ignition timing of about 20°CA BTDC, the two-part mixtures have been shown to form a stable and richer stratified mixture around the ignition point, and the maximum global air-fuel ratio reaches to 60: 1.     

土压平衡盾构施工中泡沫改良砾砂土的试验研究

为了解决土压平衡盾构在砾砂土地层掘进过程中,土体塑流性差、刀盘及螺旋输送机磨损严重和开挖面平衡不易保持等问题,通过自制泡沫发生器发泡,对砾砂土地层的泡沫改良技术进行室内试验研究,分析气液比、含水率和泡沫掺量对塑流性的影响和改良前后土样的渗透系数的变化规律,得出泡沫发生器气液比在30∶1~55∶1、含水率为5%~12.5%、泡沫掺量为20%~40%时,土体具有较好的塑流性,泡沫的"轴承效应"和泡沫剂中表面活性剂的亲水基团与水、砾砂土颗粒形成的氢键是塑流性提高的根本原因;使用泡沫剂改良砾砂土后,渗透系数大幅降低,掺泡沫后在280 min内渗透系数随时间变化较小,能达到10~(-5)cm/s,泡沫剂溶液中高分子化合物的联结和液桥力是土样具有堵水作用的原因。     

A new model for temporal–spatial stochastic analysis of vehicle–track coupled systems

The vehicle–track coupled system has a random nature in the time–space domain. This paper proposes a computational model to analyse the temporal–spatial stochastic vibrations of vehicle–track systems, where the vehicle–track system is divided into a vehicle subsystem, track subsystem, and interfacial subsystem between the wheel and rail. In this model, the time-varying randomicity of dynamical parameters of the vehicle system, correlation, and randomness of the track structural parameters in the time–space joint dimensions, and randomness of the track random irregularities are considered. A probability dimension-reduction method was used to randomly combine different random variables. Furthermore, the probability density evolution method was applied to solve the delivery problem of probabilities between excitation inputs and response outputs. The temporal–spatial stochastic vibrations of the vehicle–track system with different coefficients of variation were studied, in which we assumed that the dynamic parameters obeyed the normal distribution, and the stochastic simulation method of the track random irregularities is probed into. The calculated results from this model are consistent with the actual measured results and physical conceptions. Thus, the temporal–spatial stochastic evolutionary mechanism can be explored, and the limits of dynamic indices can be formulated by using this developed model.     

超高压共轨系统轨压控制策略研究

为稳定控制超高压共轨系统中的共轨腔压力并缩短轨压控制算法的开发周期,利用AMESim/Simulink联合仿真技术建立了超高压共轨系统轨压控制仿真模型,采取前馈+PID控制算法设计了轨压控制策略,并针对轨压控制中的瞬态和稳态工况进行了仿真计算,最后在试验台架上开展了轨压跟随性测试。结果表明:所制定的前馈+PID控制算法能使轨压稳定在目标轨压附近,上下波动小于3 MPa,且轨压突变时瞬态响应时间小于0.5s,控制结果能够满足超高压共轨系统对精度和速度的需求。     

基于一维-三维耦合仿真的进气系统优化方法

提出了基于一维-三维耦合仿真的进气系统优化方法,此方法兼具CFD对进气系统三维流动特性准确描述与一维仿真对内燃机进气系统全局控制的优点。建立了进气歧管三维模型,采用GT-Power软件进行缸内工作过程模型仿真,根据试验数据标定仿真模型。通过一维-三维耦合仿真计算得到进气歧管各转速下的流动参数,以此作为CFD仿真的边界条件,优化进气歧管的结构参数。通过整机试验对进气歧管流动性能进行了验证。试验结果表明,该方法能够较好地指导进气歧管设计。