公共交通系统营运可靠性研究

优先发展公共交通是大城市解决交通拥堵,实现城市交通可持续发展的一项重要措施,然而,公交营运水平的低下制约着公交的发展。本文借鉴可靠性理论对公共交通营运可靠性进行定义,并对公交营运时间和乘客服务可靠性分别进行了描述,据此建立起公交系统营运可靠性模型,然后采用随机模拟技术(即Monte Carlo模拟)进行求解,通过算例说明模型的可行性,最后通过分析可靠性模型得出大型活动期间改善公交营运的途径。     

柴油机曲轴有限元计算与台架试验数据对比分析

目前，国内柴油机行业普遍使用的曲轴弯曲疲劳强度试验台架，均采用音叉共振板结构。该试验台架对于大多数常规结构曲轴的连杆轴颈圆角疲劳强度的测定是比较准确的，但对于有些特殊结构曲轴的试验，却未能取得理想结果。以某曲轴台架试验、台架仿真模型及有限元计算模型数据为基础，分析对比了不同模型数据的差异及产生原因。     

管桩加固软土路基桩土相对位移分析

管桩加固软土路基作为一种新的处理方式可以有效地解决路基稳定和总沉降的问题,但是桩顶平面会产生较大的桩土相对位移。对桩土相对位移的形成机理进行分析,利用桩土相对位移的原型观测试验,从变形的角度研究桩土协同工作性状,同时提出了桩土相对位移的控制方法。     

光纤光栅孔隙水压力计的研制与应用研究

阐述了光纤Bragg光栅(FBG)技术的原理以及传感器的结构设计原理和方法,采用光纤Bragg光栅(FBG)传感技术研制了适合岩土工程使用的光纤光栅孔隙水压力计,对研制的6支光纤光栅孔隙水压力计进行了试验检验并埋设于某高速公路软土路基中试测孔隙水压力以检验研发成果。实践结果表明该仪器克服了常规仪器的某些缺点,并有稳定性好、耐腐蚀等优点,可以较好地应用于岩土工程监测当中。本仪器的研制对于光纤传感技术在岩土工程领域的应用具有积极的推动作用。     

建筑物受深基坑开挖影响的显式差分分析

在基坑开挖过程中，临近重要建筑物的保护是一个重要的研究课题，通过天津地铁营口道车站深基坑开挖的模拟分析可以看出，地表沉降、墙体变位、基坑隆起三者之间存在着明显的关系，临近基坑建筑物沉降变形与其基坑的接近度有明显关系，施工过程中应综合考虑技术可行性、安全、环保、质量、工期、效益等因素采取保护措施。     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

Target priority determination methods by interval-valued intuitionistic fuzzy sets with unknown attribute weights

The paper aims at the problem of multi-targets threat degree being hard to be evaluated accurately in complex air defense battlefield environments. Combined with multi-sensors information fusion and interval-valued intuitionistic fuzzy sets (IVIFS) theories, the target priority determination is studied. The score and accuracy functions of IVIFS are improved with thinking about the hesitating information in order to increase the rationality. Then, the influence factors of target priority and the nonlinear relationship between the influence factors and target priority are analyzed. Next, the algorithms for calculating the factor weights and sensor weights are given. Based on the theory of IVIFS and technique for order preference by similarity to an ideal solution (TOPSIS), two methods of target priority determination based on the IVIFS and TOPSIS are proposed. At last, an application example verifies the effectiveness and flexibility of the proposed algorithms.     

鱼雷发动机三组元比例控制器数值模拟

利用计算流体力学软件Pumplinx模拟鱼雷发动机中三组元比例控制器的内部流场,分析计算中不同压差情况下对比例控制器性能的影响,以及叶片与定子间间隙大小对于比例控制器性能的影响,同时对不同叶片数目下性能进行对比。计算结果表明:由于比例控制器为被动旋转马达结构,其转速和流量均随时间呈周期性脉动变化,随着工作压差增大,转速脉动幅度基本保持不变,而流量和扭矩脉动幅值增加;随着间隙增大,泄漏量增大,但流量、扭矩、转速脉动幅值大幅降低,出口流量较为平稳;叶片数目增多后比例控制器转速降低、排量降低。由计算结果推断出目前比例控制器的最优叶片数目为4。本文可为进一步研究比例控制器精度问题提供参考。     

逆变器复合控制方案稳定性准确性和快速性的判定方法研究

本文针对重复控制加PI控制的复合控制方案,参照重复控制稳定性、准确性和快速性的判定方法总结出适用于复合控制方案的判定方法。并将重复控制器与复合控制方案的特性进行了对比,从理论上说明了判据的有效性。最后通过仿真进一步验证复合控制方案的判定方法。     

Effect of interference fits on the fatigue lives of bolted composite joints

The effect of interference fits on the fatigue lives of bolted composite joints is investigated by conducting mechanical tests. Static and fatigue tests are carried out on specimens made of carbon-bismaleimide composites joined together as double-lap single-bolt joints. The bolts having interference fits ranging of 0 (neat fit), 0.5%, 0.75% and 1% are performed. The results demonstrate the relationship between fatigue life and different values of interference fits. After the fatigue tests, non-destructive evaluation (NDE) and scanning electron microscope (SEM) are used to observe the damage of the surrender and surface of the hole. The test results show that the interference fitted specimens have improved fatigue life compared to the neat fitted specimen. The NDE and SEM results reveal that the damage degree of interference fitted specimen is weaker than that for the neat fitted one.