Approximate optimal AUTOSAR software components deploying approach for automotive E/E system

The AUTOSAR has been developed as the worldwide standard for automotive E/E software systems, making the electronic components of different suppliers to be employed universally. However, as the number of component-based applications in modern automotive embedded systems grows rapidly and the hardware topology becomes increasingly complex, deploying such large number of components in automotive distributed system in manual way is over-dependent on experience of engineers which in turn is time consuming. Furthermore, the resource limitation and scheduling analysis make the problems more complex for developers to find out an approximate optimal deploying approach in system integration. In this paper, we propose a novel method to deploy the AUTOSAR components onto ECUs with the following features. First, a clustering algorithm is designed for deploying components automatically within relatively low time complexity. Second, a fitness function is designed to balance the ECUs load. The goal of our approach is to minimize the communication cost over all the runnable entities while meeting all corresponding timing constraints and balancing all the ECUs load. The experiment results show that our approach is efficient and has well performance by comparing with other existing methods in specific and synthetic data set.     

潮位变化对上海某越江盾构隧道变形的影响规律研究

为了探究潮位变化与越江盾构隧道的沉降和收敛变形之间的关联性,采用数据统计分析、相关性分析和周期性分析方法,对上海某越江盾构隧道的监测数据与同时期隧道上部的潮位变化进行研究分析。研究表明:1)江中段隧道在潮位变化的作用下产生均匀沉降,其波动性与潮位起伏具有近似的周期性;2)陆域段隧道沉降变化的波动性程度与河流的距离有关;3)潮位变化引起隧道管片断面的横径和竖径产生循环的收敛变形,其横径收敛变形大于竖径收敛变形。以上研究可为越江盾构隧道设计、施工和运维提供参考。     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

A receding horizon sliding control approach for electric powertrains with backlash and flexible half-shafts

Active control of electric powertrains is challenging, due to the fact that backlash and structural flexibility in transmission components can cause severe performance degradation or even instability of the control system. Furthermore, high impact forces in transmissions reduce driving comfort and possibly lead to damage of the mechanical elements in contact. In this paper, a nonlinear electric powertrain is modelled as a piecewise affine (PWA) system. The novel receding horizon sliding control (RHSC) idea is extended to constrained PWA systems and utilised to systematically address the active control problem for electric powertrains. Simulations are conducted in Matlab/Simulink in conjunction with the high fidelity Carsim software. RHSC shows superior jerk suppression and target wheel speed tracking performance as well as reduced computational cost over classical model predictive control (MPC). This indicates the newly proposed RHSC is an effective method to address the active control problem for electric powertrains.     

面向控制的SCR催化转化器温度模型

为了建立面向控制的SCR催化器温度模型,根据能量守恒和质量守恒方程并考虑热平衡中所涉及的换热过程不同,建立了4种SCR催化器温度的数学模型,并利用Matlab/Simulink构建图形化的计算模型。采用柴油机欧洲稳态循环(ESC)和欧洲瞬态循环(ETC)条件下的台架实测数据对模型进行检验,基于最大离散程度、拟合度和计算时间3个指标对模型进行评价和比较。结果表明,考虑催化器与废气和周围环境对流换热的温度模型具有良好的预测精度和实时性,更适合用于SCR控制策略。     

柴油机气门导管断裂影响因素分析及改进

针对某柴油机气门导管在整机台架试验过程中发生的横断和纵裂失效故障,对气门导管的材料性能、结构应力、微动磨损、热变形、装配工艺等影响因素进行了分析。分析结果表明:材料力学性能差和装配过盈量较大造成的应力集中和微动磨损是气门导管横断的主要原因;液氮人工压装的装配工艺是造成气门导管纵裂的主要原因。据此提出新方案气门导管,并通过了整机台架试验验证。     

钢箱梁桥地震响应的有限元分析

针对典型的工程实例,基于大型有限元软件,采用纤维模型模拟梁柱单元,建立了钢箱梁桥的三维有限元模型,合理选取了强震记录,进行了罕遇地震作用下桥梁结构的弹塑性时程分析,为桥梁结构抗震设计和提高抗震安全性提供了科学依据和重要参考.     

大型活动交通影响评价方法

大型活动吸引和产生的突增交通量会造成周边地区的交通拥挤。通过比较大型活动与大型商业建设项目的交通影响评价特点和分析大型活动交通管理的影响因素,分别针对“提供一次性服务的大型活动”和“提供长效服务的大型活动”,设计了交通需求的预测方法。以交叉口服务水平分析方法为基础,提出一种了大型活动的交通影响评价方法。以长春市南岭体育场举办的“中国足球甲A联赛”为对象,运用Vissim微观交通仿真软件对所提出的方法进行了初步验证。结果表明,在大型活动条件下,所提出的方法能够确定需要进行交通管制的空间范围。     

新加坡公共交通发展经验及启示

通过实际考察和走访咨询,系统地总结了新加坡的公共交通发展经验。首先介绍了新加坡对小汽车和公共交通发展采取的＂推、拉策略＂,以及新加坡公共交通的发展历程。在此基础上,对新加坡公共交通发展的成功经验进行了归纳和总结,包括管理机制、公共交通设施建设、公共交通运营系统、政策法规等方面的内容。结合我国城市交通发展的现状和特点,对城市公共交通的发展提出了措施和建议。     

公交通行能力约束的智能调度优化模型

公交通行能力是解决城市交通拥堵问题、促进城市公共交通系统高效运行的要素之一。介绍了公交通行能力的计算要素,并针对目前我国城市由于盲目调度造成的公交系统运营效率、服务水平下降的问题,提出将公交通行能力作为约束条件对公交调度进行优化。鉴于公交企业制订调度方案时需兼顾公交服务水平和企业效益,将智能调度的目标确定为候车时间满意度、候车空间满意度、车内舒适满意度和企业满意度加权平均值最大,并给出了相应的计算方法。最后讨论了利用遗传算法对模型进行求解的过程。