Perceived and actual costs of operating cars

The perception that drivers have of car operating costs is an important factor in determining modal split characteristics. Theoretical figures derived from discriminant analysis models suggest that drivers perceive only petrol costs, but this has not been cor roborated by detailed surveys. This report examines in detail perceived and actual journey to work petrol costs of a sample of London commuters. The perception is also examined of related factors, such as petrol consumption and distance, in an attempt to throw some light on the perception mechanism itself.     

Junction interactions and monotonicity in traffic assignment

We consider the traffic equilibrium problem when the travel demand is inelastic and stationary in time. Junction interactions, which abound in urban road networks, are permitted. We prove that the set of equilibria (solutions to the assignment problem) is convex when certain monotonicity and continuity conditions are statisfied at each junction.     

The dynamics of traffic assignment and traffic control: A theoretical study

The paper considers traffic assignment, with traffic controls, in an increasingly dynamic way. First, a natural way of introducing the responsive policy, P_o, into steady state traffic assignment is presented. Then it is shown that natural stability results follow within a dynamical version of this static equilibrium model (still with a constant demand). We are able to obtain similar stability results when queues are explicitly allowed for, provided demand is constant. Finally we allow demand to vary with time; we consider the dynamic assignment problem with signal-settings now fixed. Here we assume that vehicles are very short and that deterministic queueing theory applies, and show that the time-dependent queueing delay at the bottleneck at the end of a link is a monotone function of the time-dependent input profile to the bottleneck. We have been unable to obtain results when dynamic demand and responsive signal control are combined.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

Policy challenges of increasing automation in driving

The convergence of information and communication technologies (ICT) with automotive technologies has already resulted in automation features in road vehicles and this trend is expected to continue in the future owing to consumer demand, dropping costs of components, and improved reliability. While the automation features that have taken place so far are mainly in the form of information and driver warning technologies (classified as level I pre-2010), future developments in the medium term (level II 2010–2025) are expected to exhibit connected cognitive vehicle features and encompass increasing degree of automation in the form of advanced driver assistance systems. Although autonomous vehicles have been developed for research purposes and are being tested in controlled driving missions, the autonomous driving case is only a long term (level III 2025 +) scenario. This paper contributes knowledge on technological forecasts regarding automation, policy challenges for each level of technology development and application context, and the essential instrument of cost-effectiveness for policy analysis which enables policy decisions on the automation systems to be assessed in a consistent and balanced manner. The cost of a system per vehicle is viewed against its effectiveness in meeting policy objectives of improving safety, efficiency, mobility, convenience and reducing environmental effects. Example applications are provided that illustrate the contribution of the methodology in providing information for supporting policy decisions. Given the uncertainties in system costs as well as effectiveness, the tool for assessing policies for future generation features probabilistic and utility-theoretic analysis capability. The policy issues defined and the assessment framework enable the resolution of policy challenges while allowing worthy innovative automation in driving to enhance future road transportation.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

Influence of AC system design on the realisation of tractive efforts by high adhesion locomotives

The main task for heavy haul railway operators is to reduce the cost of exported minerals and enhance the long-term viability of rail transport operations through increasing productivity by running longer and heavier trains. The common opinion is that this is achievable by means of implementation of high adhesion locomotives with advanced AC traction technologies. Modern AC high adhesion locomotives are very complex mechatronic systems and can be designed with two alternative traction topologies of either bogie or individual axle controls. This paper describes a modelling approach for these two types of AC traction systems with the application of an advanced co-simulation methodology, where an electrical system and a traction algorithm are modelled in Matlab/Simulink, and a mechanical system is modelled in a multibody software package. Although the paper concentrates on the analysis of the functioning for these two types of traction control systems, the choice of reference slip values also has an influence on the performance of both systems. All these design variations and issues have been simulated for various adhesion conditions at the wheel–rail interface and their influence on the high traction performance of a locomotive equipped with two three-axle bogies has been discussed.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.