Application of warm forming aluminum alloy parts for automotive body based on impact

Aluminum alloys are important technological materials for the application on lightweight design and development of vehicle body. The research works for characterizing warm forming behavior of aluminum alloys have generally reported. However, there were few researches focused on the flow behavior of warm forming aluminum alloy parts for the energy absorbing performance during crash. The tensile stress-strain response for warm forming AA5182 specimens tested under the strain rates of 0.0015 s^?1, 0.015 s^?1, 0.15 s^?1 and 1.5 s^?1 are presented in this paper. The data were fit to the Johnson-Cook constitutive model for the simulation of frontal impact. The energy absorbing performance of warm forming AA5182 parts were analyzed. The results show the higher flow stresses and lower fractured strain of warm forming aluminum alloy parts with the strain rate increasing. The flow stresses of warm forming aluminum alloy parts are insensitive to strain rate, while the fractured strain and elongation are sensitive to strain rate. The intrusion displacement of the warm forming aluminum alloy parts is appropriate for the satisfaction of vehicle body design avoiding the excessive deformation for the injury of passenger or the failure of frontal door opening. The feasibility of warm forming aluminum alloy parts is verified with the analysis of energy absorbing performance, stiffness and modal of vehicle body.     

Investigation of regenerative and Anti-lock Braking interaction

The use of a regenerative braking mode can reduce overall vehicle energy usage for most of the most common drive cycles. However, a number of technical issues restrict the use of regenerative braking for all possible braking situations. These issues are concerned with two key limitations. The first is related to physical limitations of the applied regenerative braking system, e.g. Electric Motor (E-Motor) power limits; energy storage device capacity and vehicle load transfer etc. The second limitation results from the potentially detrimental interaction between regenerative braking and the Anti-locking Braking System (ABS). The first type of limitation can, to some extent, be alleviated by suitable choice of hardware and, as a consequence, will not be discussed further in this paper. The second type of limitation concerns the regenerative braking strategies during an ABS event. Some of the regenerative braking strategies designed and investigated within the Low Carbon Vehicle Technology Project (LCVTP) will be described and analyzed in this paper. A comparison of competing strategies is made and conclusions are drawn together with suggestions for further research. The work has been progressed as a part of a major research programme; namely the LCVTP, which has been conducted within an extensive industrial and academic partnership, mutually funded by the European Regional Development Found and Advantage West Midlands.     

Pooling for the journey to work: The outlook in Great Britain

Pooling, or ride-sharing, is a term coined in the United States (U.S.) to describe various forms of collective travel organised for, and often by, specific groups of commuters with similar travel requirements. Its different forms include bus pooling (financially self-supporting works bus or commuter coach services), minibus pooling (van pooling in U.S. terminology) and car pooling. It has been claimed that these forms of collective travel offer a more personalised service than conventional stage carriage buses, and therefore have a greater chance of attracting solo car drivers and increasing vehicle occupancies. This, in turn, can lead to lower fuel consumption and reduced traffic congestion at peak times. Following the advent of oil shortages in the winter of 1973/74, considerable efforts were made in the U.S. to promote pooling initiatives. This gave rise to the publication of a substantial volume of literature that sometimes indicated significant resource-saving achievements. This paper considers the potential for bus, minibus and car pooling in Great Britain, drawing both on relevant theoretical and economic studies, and on practical operational experience. It concludes that under reasonable assumptions about the transport situation in the next decade or so, pooling could become increasingly useful for solving the travel problems of individual local groups, but that it is unlikely to become a major mode in terms of the numbers of trips carried. The effects of recent legislative changes are discussed, and the justification for further change assessed. Relevant comparisons are made with the U.S.Crown Copyright 1983. Extracts from the text may be reproduced, except for commercial purposes, provided the source is acknowledged.     

Ultimate strength design of stiffened plates under axial compression and bending

The basis for design of stiffened plates under longitudinal compression is outlined and predictions using several codes are compared against numerical results from an inelastic beam-column formulation and test results. In order to explore the inherent differences in column behaviour separately from discrepancies arising due to plate panel behaviour, the code predictions are re-evaluated adopting a common plate panel effective width formulation. On this basis, a critical review of code methods is made and some modifications are proposed.

The effect of the magnitude and direction of applied uniform bending on the axial capacity of stiffened plates is investigated by comparing two alternative design approaches, namely an interaction equation and a method based on the Perry equation, against results from numerical analyses and from rigid plastic theory. The interaction equation is invariably more conservative than the Perry approach but its simplicity tends to be convenient for routine design applications. Finally, results of numerical analyses, together with experimental results from previous studies, on continuous stiffened plates under combined axial compression and lateral pressure are presented and available design guidance is discussed.     

Investigation on Stability and Possible Chaotic Motions in the Controlled Wheel Suspension System

The suspension system has to fulfil a large number of partly contradictory requirements which can be improved by the application of controllable elements in the wheel suspension system. A number of studies dealing with the improvement of suspension characteristics have been published. In the present paper the stability of the controlled suspension systems will be examined. In the paper the stability problems of the active suspension system is analysed and the stable parameter regions are determined.     

Modeling oil spills in a river—lake system

A general model shell, ROSS3, is developed for simulating oil spills in complex river systems using techniques which have not been previously exploited in oil spill models. ROSS3's new approach has several advantages over the approach to model oil spills in the past: (a) The use of a time-varying boundary-fitted coordinate system that allows accurate accounting for complex river/lake boundary as well as the river boundary changes as its water levels fluctuate; (b) The ability to confine two-dimensional hydrodynamic computations to a limited river reach; (c) The ability to interactively layout the channel networks for setting up the model, define extra cross sections to increase the accuracy if needed, in addition to the traditional data entry and visualization interfaces.ROSS3 is a two-layer two-dimensional oip spill model that can simulate the mechanism of advection, horizontal diffusion, mechanical spreading, shoreline deposition, evaporation, dissolution, vertical mixing, resurfacing and sinking. In ROSS3 spilled oil may be a surface slick or suspended oil droplets, or a combination of both. Both free surface and ice cover conditions can be simulated. The flow of conditions can be varied and the unsteady flow model can be run within ROSS3 to simulate the flow conditions in both the river and the lake. The ice conditions can be added or removed from the model input using easy interactive procedures.     

Modeling and Dynamics of Friction Wedge Dampers in Railroad Freight Trucks

A mechanical model for the vertical response of the bolster and friction-wedge suspension elements in a railroad freight truck is developed. The model incorporates linear stiffnesses and dry friction contact between rigid elements. Numerical bifurcation diagrams for sticking events, obtained for parameterizations of the amplitude and frequency of a harmonic track excitation, and for various friction laws, reveal distinct parameter-dependent dynamic responses: strongly nonlinear stick-slip oscillations, observed away from period-1 resonance; and weakly nonlinear, nearly harmonic responses, observed near the period-one resonance. The analytical method of harmonic balance is applied to develop a first order approximation for the period-1 response, and, as should be expected, is found to correspond well with the numerical results in the large amplitude limit and near the resonance location. Given that such weakly nonlinear, large amplitude, period-1 responses are not common for the speeds and system parameters of most freight vehicles, we conclude that friction-wedge models based on some form of equivalent linearization may be inadequate for simulating freight car dynamics in many cases of practical importance.     

The changing face of parking-related data collection and analysis: The role of new technologies

Current trends in requirements for parking related information and in the availability of data are reviewed. Important influences include the increased need for data to assist in the efficient operation and management of parking stock and to assess the impact of parking on the local network and economy. New sources of data are described, particular attention being given to the availability of data as a byproduct of parking management systems and computerised enforcement systems. The use and performance of audio, video and data loggers in parking surveys is discussed as is the role of computers in questionnaire surveys. New methods of analysis involving spreadsheets, graphics and analysis software, links with databases and simulation models are outlined.