Estimation of the effects of aircraft noise on residential satisfaction

This study assesses the effects of aircraft noise on residential satisfaction, an important indicator of subjective well-being. A structural equation model is specified that estimates the relationships between objective variables, noise annoyance variables and residential satisfaction. Secondary data-analysis is used to estimate the model. The survey was conducted in 1996/1997 among the population living within a 25-km radius of Amsterdam Schiphol, the largest airport in the Netherlands. The effect of aircraft noise annoyance is found to be relatively small. In addition, the objective level of aircraft noise exposure is found to be a better predictor of residential satisfaction than its subjective counterpart. The most important determinants of residential satisfaction are found to be road traffic noise annoyance, age and neighbor noise annoyance.     

Efficiency and ecological characteristics of a VCR diesel engine

Compression ratio (CR) is a design parameter with highest influence on efficiency, emission and engine characteristics. In conventional internal combustion (IC) engines, the compression ratio is fixed and their performance is, therefore, a compromise between conflicting requirements. One fundamental problem is that drive units in the vehicles must successfully operate at variable speed and loads and in different ambient conditions. If a diesel engine has a fixed CR, a minimal value must be chosen that can achieve a reliable self-ignition when starting the engine in cold start conditions. In diesel engines, variable compression ratio (VCR) provides control of peak cylinder pressure, improves cold start ability and low load operation, enabling the multi-fuel capability, increase of fuel economy and reduction of emissions. By application of VCR and other mechanisms, the optimal regime fields are extended to the prime requirements: consumption, power, emission, noise, etc., and/or the possibility of the engine to operate with different fuels is extended. An experimental Diesel engine has been developed at the Faculty of Engineering, University of Kragujevac. The changes of CR are realized by changing the piston chamber diameter. Detailed engine tests were performed at the Laboratory for IC engines. Special attention has been given to decrease of fuel consumption and exhaust emissions. An optimal field of CR variation has been determined depending on the given objectives: minimal fuel consumption, minimal nitric oxides, and particulate matter emissions, etc.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.     

Global supply chain and port/terminal: integration and competitiveness

Much has been said of the importance of port and terminal integration in the supply chain. Authors have stressed the importance of agility to the port environment, which involves being proactive along supply chains, facilitation of intermodal integration, as well as organizational integration and partnership between ports and users. Despite the well articulated importance of the issues, little has been offered in terms of conceptualizations and empirical evidence of what really is meant by port/terminal integration in the supply chain, how such integration can be measured and quantified as well as the extent to which different ports/terminals in the world are integrated in the supply chain and competitive performance implications arising thereof. This paper aims to make a contribution in this respect by (i) reviewing the relevant literature on supply chain integration and port integration in the supply chain, (ii) conceptualizing measures for port/terminal integration in the supply chain, (iii) empirically testing the influence of port/terminal integration in the supply chain on port competitiveness and (iv) outlining the significance and value of the study for port operators, shipping lines, transport providers and for further research.     

A Multi-Spoke, Three Plane Tyre Model for Simulation of Transient Behaviour

Based on the multi-spoke, single-plane, steady-state tyre model, a transient multi-spoke, three-plane tyre model is presented. This model involves updating the states of all the spokes under consideration to t+dt from the corresponding states at t. Also, a spoke base, which has lateral and longitudinal flexibilities relative to wheel hub, is included. By adding two extra planes of spokes to the original one, the effect of tyre width is built into the model. The three planes are equally spaced across the width of the tyre. The interaction with the ground of the spokes on these three planes is used to represent that of tyre elements at different locations across the width. Analytical results show good qualitative agreement with published experimental data. This model can be used to illustrate transient tyre behaviour and in simulations in which a generic tyre will suffice.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Influence of vehicular traffic on urban air quality – A case study of Hyderabad,India

In the present study, impact of vehicular traffic emissions on black carbon aerosol mass concentration, trace gases and ground reaching solar radiation were analyzed during nationwide truck strike of 5–12 January, 2009 over urban environment of Hyderabad, India. A significant reduction of about 57%, 60%, 40% and 50% was observed in black carbon, particulate matter, carbon monoxide and ozone respectively during nationwide truck strike period. Results of the study are important for source apportionment of pollutants as the strike created natural laboratory for studying the impact of diesel operated trucks on urban air quality.     

Application of genetic algorithms for joint optimization of signal setting parameters and dynamic traffic assignment for the real network data

This paper presents the joint optimization of signal setting parameters and dynamic user equilibrium (DUE) traffic assignment for the congested urban road network. The simulation-based approach is employed to obtain the DUE condition for the case of multiple-origin multiple-destination traffic flows. The dynamic traffic assignment simulation program (DTASP), developed in C language is used to assign the traffic dynamically on the road network, whereas method of successive averages (MSA) is modified and used to arrive at the DUE condition. The artificial intelligence technique of genetic algorithms (GAs) is applied to obtain the optimal signal setting parameters and path flow distribution factor for DUE condition. The methodology developed in such a way that joint optimization of signal setting parameters with DUE is obtained. The proposed method is applied to the real network data of Fort Area of Mumbai city comprising of 17 nodes and 56 unidirectional links with 72 Origin–Destination pairs, where all the 17 nodes are signalized intersections. The traffic flow condition for the optimized signal setting parameters is considerably improved compared to the existing signal settings. The results prove that the GA is an effective technique to solve the joint optimization problem for the real network data.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.