Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.     

Examination of PN emissions and size distributions of a hybrid city bus under real world urban driving conditions

Engine load-speed frequency map of a hybrid city bus, which operates on the routes of Sakarya Municipality, was compared with that of European Transient Cycle (ETC) and World Harmonized Transient Cycle (WHTC), which are the certification test cycles. It was observed that the hybrid city bus engine operates mostly at three main regions, which are idling (30% load and 750 rpm), motoring (0% load and 1200 rpm) and high load (80% load and 1800 rpm) conditions under real world urban driving conditions. However, engine load-speed frequency maps of the certification test cycles are significantly different and cannot represent the real world urban driving conditions of the hybrid city bus. Therefore, the Particle Number (PN) emissions of the hybrid city bus were investigated under real world urban driving conditions. The aims of work were to examine the effects of city bus hybridization on the particle emissions and develop PN emission factors. The PN concentrations and size distributions together with engine operating conditions were measured with a Particle Measurement Program (PMP) compliant system, which involves a condensation particle counter (CPC) and a particle sizer (EEPS). The measurements under real world urban driving conditions indicated that the emission factors of the hybrid city bus for the PN and Total PN are 8.99E+12 and 2.51E+13 #/kW-h, respectively. The PN size distribution measurements indicated that the particles up to approximately 20 nm are not very sensitive to changes in engine power and they are exist even during motoring conditions. But, the particles in the size range from 20 to 200 nm are very sensitive to sudden changes of the engine power.     

RECENT DEVELOPMENT OF PROCESS SIMULATION AND ITS APPLICATIONS TO MANUFACTURING PROCESSES

l.IntroductionThemostboortantdrivingforceinmanufacturillistoPrOduCeabetterPrOductatalowercost.GenerallyeffecthemethodsinchideshOrtenintheleadtiminthedesigncyCle,andredUcinthetoolingcostandmaChinedOWnmeatProductionst4e.AllOfthemrewtabettertmderstandingofhO…     

Influence of load and inflation pressure on the tyre rolling resistance

Tyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper test conditions in the future standardized on-road method of measuring rolling resistance. The results indicate that while an increase of load always leads to the increase of rolling resistance force, the influence on Coefficient of Rolling Resistance is more complicated and unpredictable. They also indicate that tyres with high rolling resistance are more sensitive to inflation pressure changes than low rolling resistance tyres.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Multiaxial stress creep rupture mechanisms of AZ31 magnesium alloy

The maximum principal stresses, von Mises effective stresses and principal facet stresses at the time of creep rupture were compared in uniaxial, biaxial, and triaxial stress states for AZ31 magnesium alloy. The creep rupture of this alloy was experimentally controlled by cavitation, which was the result of a low damage tolerance, λ. Creep deformation could be correlated with the von Mises effective stress parameter. The failure-mechanism control parameter governing the stress state coincided with the experimental results of the rupture of the materials under multiaxial stress states. Finally, the theoretical prediction based on constrained cavity growth and continuous nucleation agreed with the experimental rupture data to within a factor of three.     

Effect of rear slant angle on vehicle crosswind stability simulation on a simplified car model

It is important to know the effect of the aerodynamic forces and moments on driving stability because it is responsible for the excitation and influences the response of the vehicle. The purpose of this paper is to study the effect of rear slant angle of a surface vehicle on crosswind sensitivity for stability analysis. The vehicle mathematical model used to conduct a dynamic simulation was based on a simple reduced order lateral dynamics of sideslip and yaw rate motion coupled with aerodynamics model. The intention here is to compare the effect of rear slant angles response to crosswind and to rank the crosswind sensitivity ratings. The aerodynamic loads are defined as the function of the aerodynamic derivatives from the static wind tunnel tests. Result shows a 20° rear slant angle demonstrates the highest rating of crosswind sensitivity, while zero degree slant exhibits the least.     

Propagating buckles in corroded pipelines

Rigid–plastic solutions for the steady-state, quasi-static buckle propagation pressure in corroded pipelines are derived and compared to finite element predictions (ABAQUS). The corroded pipeline is modeled as an infinitely long, cylindrical shell with a section of reduced thickness that is used to describe the corrosion. A five plastic hinge mechanism is used to describe plastic collapse of the corroded pipeline. Closed-form expressions are given for the buckle propagation pressure as a function of the amount of corrosion in an X77 steel pipeline. Buckles that propagate down the pipeline are caused by either global or snap-through buckling, depending on the amount of corrosion. Global buckling occurs when the angular extent of the corrosion is greater than 90°. When the angular extent is less than 90° and the corrosion is severe, snap-through buckling takes place. The buckle propagation pressure and the corresponding collapse modes also compare well to finite element predictions.     

Improving pollutant emissions in diesel engines for heavy-duty transportation using retarded intake valve closing strategies

A combined theoretical and experimental study has been carried out to determine the real potential of reducing pollutant emissions in a HD diesel engine by means of retarding the intake valve closing. The effects produced by this alteration of the basic operation cycle have been examined by a preliminary modelling study, and from the obtained results, a modified camshaft was manufactured with a delayed intake valve closing of 60 crank angle degrees. Single-cylinder engine tests were carried out with this modified camshaft, and the emissions and fuel consumption were recorded. The results showed that the retarded intake valve closing can enhance the premixed combustion phase, and thus simultaneously reduce soot and NOx emissions. Moreover, the combustion process attained is extremely tolerant to exhaust gas recirculation, and by adoption of this measure, Euro-5 emissions limits can be achieved at the tested conditions without after-treatment.