Piston-temperature measuring system using electromagnetic induction with verification by a telemetry system

The development of an inner-piston-chamber temperature measurement system is a necessary step in engine development or when solving other fundamental problems related to automotive engines. There are various pre-existing measurement methods available, e.g., the linkage method, piston telemetry, templog, and the electromagnetic induction method. In this study, we first redesigned the coil sensor used in the electromagnetic induction method using PEEK and then used Taguchi methods to reduce the number of experiments in the development process and finally utilized piston telemetry via Bluetooth to verify the precision and accuracy of the redesigned PEEK coil sensor and electromagnetic induction method. The results displayed a reproducibility within 0.5 degrees and an accuracy within 2 degrees Celsius.     

Parameter identification for a LuGre model based on steady-state tire conditions

The purpose of this study was to effectively identify parameters for a LuGre friction model based on experimental measures. In earlier work related to this study (Yang et al., 2009), which was based on the characters of polygonal wear (Sueoka and Ryu, 1997), we showed a frictional vibration model for a mass on a moving belt. This model reflected lateral vibrations caused by velocity and toe-in angle. An important aspect of the present study is the improved friction model. A previous friction model, which divided the process into four parts, expressed the sable excited vibration well but failed to reflect the hysteresis loop change when vehicles accelerated or decelerated continuously. A LuGre friction model can solve this problem, but several model parameters must be obtained experimentally. We measured contact width and length of tires as vertical pressure changed; this provided a theoretical basis for apparent stiffness of a unit of tire tread. Based on tire data from Bakker E’s article in a SAE paper from 1987, we identified the Stribeck exponent and Stribeck velocity in LuGre. Then, the results were implemented in a vibration system that verified the rationality of the data.     

Performance optimization of CVT for two-wheeled vehicles

Continuously Variable Transmission (CVT) is one of the most promising automotive transmission technologies because of its continuously variable gear ratio and reduced shift shock. CVT is different from Manual Transmission and Automatic Transmission, and it is possible to operate the power source in its high efficiency region with CVT in the drive train. Several types of CVT exist that can be categorized based on the mechanism of power transmission, such as the belt pulley, traction drive, and hydrostatic types. This paper investigates the belt pulley CVT, which consists of a thrust actuator, driver pulley, belt, driven pulley, and preload spring of the output shaft. A complete CVT is constructed, and based on that a simulation program that analyzes the static performance of a CVT is implemented in Matlab/Simulink. From these simulation results, methods for improving the efficiency of the CVT are discussed. The coefficient of the torque capacity factor is proposed as affecting the matching between a power source and a CVT, and methods for improving the matching effect are also investigated.     

Engine performance and toxic gas analysis of biobutanol-blended gasoline as a vehicle fuel

A comprehensive study evaluating the performance of biobutanol-blended gasoline in passenger cars was conducted because biobutanol is considered a better biofuel than bioethanol as it has no water solubility and it has a higher caloric value, giving it a higher energy value. Several kinds of samples—suboctane gasoline, 8 volume percentage and 16 volume percentage biobutanol—blended gasoline, and a 10 volume percentage MTBE-blended market sample (as the oxygencontaining gasoline)-were tested to evaluate the engine performance in terms of the detergency of the intake valves and combustion chambers, power, emissions, and fuel efficiency. Additionally, the toxicity of the emissions from these biobutanolblended samples was tested in order to assess the viability of biobutanol as one of the competitive potential substitutes for MTBE as an oxygenator in the near future. The results show that biobutanol-blended gasoline samples had relatively better detergency, relatively higher power, and similar levels of emissions compared with those of MTBE-blended gasoline. Formaldehyde was emitted from all of the samples at almost the same levels and within the error range, whereas biobutanolblended gasoline samples emitted approximately three times the amount of acetaldehyde than did the suboctane gasoline. This study shows that biobutanol is one of the best alternative bioalcohol fuels for use in the near future.     

Quality evaluation of car window motors using sound quality metrics

In this paper, a method to establish a decision criterion to evaluate the quality of small window motors using sound quality (SQ) metrics is suggested. Although the sound level radiated from the motor is relatively small compared to other sounds in a car, the sound from an abnormal motor gives an uncomfortable feeling and the impression of abnormal operation, which can lead to customer complaints. To construct an objective decision criterion, the correlation between the SQ metrics and the subjective decision on the passing or failure of the motor were investigated. Four representative SQ metrics, viz., loudness, sharpness, roughness, and fluctuation strength, were calculated for the collected samples. It was observed that the loudness and roughness of the motor sample group classified as abnormal was higher than those of the normal motors. For a single figure rating for motor quality, an evaluation index for the motor sound was generated by combining the correlated SQ metrics with proper weightings. Evaluation results on the specimens that were not employed in generating the quality evaluation index showed a reasonable agreement with the subjective test at 73%. The suggested quality check method can replace the current subjective decision procedure to identify the faulty motors.     

Damper modeling for dynamic simulation of a large bus with MR damper

In this study, a large bus is tested to measure its dynamic response by the single-lane change test and the rapid stop test. A full car model is established by ADAMS/Car for computer simulation. For multibody modeling of a large bus, user-defined templates are used in the simulation. Simulation results of the single-lane change test and the rapid braking test are compared to the results of the physical experiments, in which several sensors are installed to measure the vehicle’s responses. The results obtained from the simulation show good agreement with the tests’ results. A dynamic model for the MR(magnetic-rheological) damper is also developed by employing the Magic Formula model, which is widely used in the nonlinear modeling of a tire. Bump simulation of a full car with the MR damper is carried out to verify the performance of the MR damper. The comparison of the simulation results obtained with the MR damper model to the results obtained with the traditional passive damper model showed improved response of the vehicle with the MR damper.     

The price of uncertainty in pavement infrastructure management planning: An integer programming approach

Currently there is a true dichotomy in the pavement maintenance and rehabilitation (M&R) literature. On the one hand, there are integer programming-based models that assume that parameters are deterministically known. On the other extreme, there are stochastic models, with the most popular class being based on the theory of Markov decision processes that are able to account for various sources of uncertainties observed in the real-world. In this paper, we present an integer programming-based alternative to account for these uncertainties. A critical feature of the proposed models is that they provide – a priori – probabilistic guarantees that the prescribed M&R decisions would result in pavement condition scores that are above their critical service levels, using minimal assumptions regarding the sources of uncertainty. By construction of the models, we can easily determine the additional budget requirements when additional sources of uncertainty are considered, starting from a fully deterministic model. We have coined this additional budget requirement the price of uncertainty to distinguish from previous related work where additional budget requirements were studied due to parameter uncertainties in stochastic models. A numerical case study presents valuable insights into the price of uncertainty and shows that it can be large.     

Mesoscale subduction at the Almeria–Oran front: Part 1: Ageostrophic flow

This paper presents a detailed diagnostic analysis of hydrographic and current meter data from three, rapidly repeated, fine-scale surveys of the Almeria–Oran front. Instability of the frontal boundary, between surface waters of Atlantic and Mediterranean origin, is shown to provide a mechanism for significant heat transfer from the surface layers to the deep ocean in winter. The data were collected during the second observational phase of the EU funded OMEGA project on RRS Discovery cruise 224 during December 1996. High resolution hydrographic measurements using the towed undulating CTD vehicle, SeaSoar, traced the subduction of Mediterranean Surface Water across the Almeria–Oran front. This subduction is shown to result from a significant baroclinic component to the instability of the frontal jet. The Q-vector formulation of the omega equation is combined with a scale analysis to quantitatively diagnose vertical transport resulting from mesoscale ageostrophic circulation. The analyses are presented and discussed in the presence of satellite and airborne remotely sensed data; which provide the basis for a thorough and novel approach to the determination of observational error.     

Traffic noise studies in a tropical environment

This paper reports upon a survey of traffic noise annoyance in three residential districts of Trinidad, West Indies. Householder perceptions were solicited by means of a questionnaire survey and direct measurements of traffic noise levels were taken. The results were compared with surveys elsewhere. It was concluded that household status had little effect on annoyance perception, that at L₁₀ levels greater than 70 dB(A) at a dwelling facade the noise level is unacceptable. L₁₀ levels less than 65 dB(A) at the building facade are not perceived as annoying in the environment considered.