Evaluating the energy performance of a SUV hybrid electric vehicle

This paper analyzes the energetic performance of the hybrid Lexus RX 400h, through on-board measurements. Several speed profiles were analyzed, for three driving types, successive stop and go cycles, three speed profiles, crossing an electronic toll collection booth, and a roundabout. In stop and go situations the internal combustion engine did not work (the torque needed to impulse the vehicle in the stop and go situations was only supported by the electric engines), as well as in the situations of constant low speeds (50 or 60 km h^?1). The auxiliary support given by the electric engines in the accelerations, as well as the importance of the energy regeneration system on the batteries’ load recovery is also demonstrated. When compared with similar conventional vehicles, the Lexus RX 400h has lower combined energy consumption between 1.2% and 60%.     

Improving the efficiency of demand-responsive paratransit services

State agencies responsible for ADA-eligible paratransit services are increasingly under pressure to contain costs and maximize service quality. Many do not operate vehicles themselves; instead, they contract out the provision of services. Contractors are paid for each hour of service. They are responsible for hiring crew, forming routes, dispatching, and operating and maintaining agency-owned vehicles. In the Twin Cities of Minneapolis and Saint Paul, Metro Mobility, the agency responsible for providing paratransit services, requires contractors to use agency-approved software for booking trips dynamically and sets parameters that guide contractors’ practices. Customer trips booked in this fashion may not utilize capacity in the most efficient manner. Therefore, beginning with the daily trip schedules generated by the software, this paper proposes two approaches for improving the efficiency of paratransit operations and estimates the benefit of using these approaches via experiments that utilize Metro Mobility data. The first approach re-optimizes routes developed at the end of each day. The second approach evaluates the benefit to state agencies of selectively using non-dedicated service providers such as taxis. Both approaches are tested on actual data obtained from Metro Mobility. The study shows that a conservative estimate of savings from re-optimization would be approximately 5% of Metro Mobility’s operating costs. Savings from the use of taxis are smaller and in the range of hundreds of dollars per day.     

Route choice of cyclists in Zurich

This paper presents the first route choice model for bicyclists estimated from a large sample of GPS observations and overcomes the limitations inherent in the generally employed stated preference approach. It employs an improved mode detection algorithm for GPS post-processing to determine trips made by bicycle, which are map matched to an enriched street network. The alternatives are generated as a random sample from an exhaustive, but constrained search. Accounting for the similarity between the alternatives with the path-size factor the MNL estimates show that the elasticity with regards to trip length is nearly four times larger than that with respect to the share of bike paths. The elasticity with respect to the product of length and maximum gradient of the route is small. No other variable describing the routes had an impact. The heterogeneity of the cyclists is captured through interaction terms formulated on their average behaviour.     

Estimation of the effects of aircraft noise on residential satisfaction

This study assesses the effects of aircraft noise on residential satisfaction, an important indicator of subjective well-being. A structural equation model is specified that estimates the relationships between objective variables, noise annoyance variables and residential satisfaction. Secondary data-analysis is used to estimate the model. The survey was conducted in 1996/1997 among the population living within a 25-km radius of Amsterdam Schiphol, the largest airport in the Netherlands. The effect of aircraft noise annoyance is found to be relatively small. In addition, the objective level of aircraft noise exposure is found to be a better predictor of residential satisfaction than its subjective counterpart. The most important determinants of residential satisfaction are found to be road traffic noise annoyance, age and neighbor noise annoyance.     

Scantling multi-objective optimisation of a LNG carrier

Numerous real-world problems related to ship design can be solved by various alternatives. However, the scantling design has conflicting objectives such as minimum production cost, minimum weight and maximum moment of inertia (stiffness). Therefore a multi-purpose solution had to be settled in order to meet all these requirements at once. Ship design is a complex endeavour requiring successful coordination of many different disciplines, both technical and non-technical. Basic design is the least defined stage of the ship design process and seeks to define the optimal amidships section structure. For that purpose, recent improvements have been made to a numerical tool in order to optimise the scantling of ship sections by considering production cost, weight and moment of inertia in the optimisation objective function. A multi-criteria optimisation of a LNG carrier is conducted in this paper to illustrate the analysis process. Pareto frontiers are obtained and results have been validated by the Bureau Veritas rules. The methodology presented in this paper has demonstrated its effectiveness in optimising scantling of ships at a very early design stage thanks to a management of critical problems usually studied at a later stage of the design.     

Efficiency and ecological characteristics of a VCR diesel engine

Compression ratio (CR) is a design parameter with highest influence on efficiency, emission and engine characteristics. In conventional internal combustion (IC) engines, the compression ratio is fixed and their performance is, therefore, a compromise between conflicting requirements. One fundamental problem is that drive units in the vehicles must successfully operate at variable speed and loads and in different ambient conditions. If a diesel engine has a fixed CR, a minimal value must be chosen that can achieve a reliable self-ignition when starting the engine in cold start conditions. In diesel engines, variable compression ratio (VCR) provides control of peak cylinder pressure, improves cold start ability and low load operation, enabling the multi-fuel capability, increase of fuel economy and reduction of emissions. By application of VCR and other mechanisms, the optimal regime fields are extended to the prime requirements: consumption, power, emission, noise, etc., and/or the possibility of the engine to operate with different fuels is extended. An experimental Diesel engine has been developed at the Faculty of Engineering, University of Kragujevac. The changes of CR are realized by changing the piston chamber diameter. Detailed engine tests were performed at the Laboratory for IC engines. Special attention has been given to decrease of fuel consumption and exhaust emissions. An optimal field of CR variation has been determined depending on the given objectives: minimal fuel consumption, minimal nitric oxides, and particulate matter emissions, etc.     

A regional railroad network optimization model for coal transportation

A regional railroad network is presented to evaluate the system's response to increased coal traffic. An optimal, multimodal, coal-shipping pattern is developed for the study region to minimize total costs and to efficiently use the existing network. A two-stage, general model allocates resources among demands and then assigns flows to the network according to efficiency criteria. The model is sufficiently general to permit modification for specific needs, assumptions and data. Government agencies and industries can apply the model in resource allocation decisions and transportation policy analysis.     

Methodology for the accuracy improvement of FEM beam type T-junctions of buses and coaches structures

The analysis of structures with finite elements methods (FEM) represents a widely spread technique. For large tubular structures similar to the buses and coaches upper structures, beam type elements are utilized due to the fact that these elements provide satisfactory results at relatively reduced computational performances. However the beam type elements have a main disadvantage determined by the fact that the modeled joints have an infinite rigid behavior. This shortcoming determines a stiffer behavior of the modeled structures which translates into an error source for the structural simulations (up to 45%). To overcome this problem, a simple methodology was conceived and an alternative optimized equivalent beam model obtained. The methodology studies the behavioral characteristics of beam modeled T-junctions determining their limitations and comparing them to equivalent T-junctions modeled with shell and volume elements. This way an improved Tjunction has been obtained, in which the behavioral error was reduced to less than 5%. Furthermore the FEM obtained results were validated with real T-junctions.     

Review of flywheel based internal combustion engine hybrid vehicles

Hybrid vehicles of different configurations and utilizing different energy storage systems have existed in development for many decades and more recently in limited production. They can be grouped as parallel, series or complex hybrids. Another classification is micro, mild and full hybrids which makes the distinction on the basis of functionality. The common energy storage systems in hybrid vehicles are batteries, supercapacitors and high speed flywheels. This paper aims to review a specific type of hybrid vehicle which involves the internal combustion engine (ICE) as the prime mover and the high speed flywheel as an energy storage device. Such hybrids are now attracting considerable interest given their potential for low cost. It is hence timely to produce a review of research and development in this subject. The flywheel is coupled to the drive line with a continuous variable transmission (CVT). The CVT can be of various types such as electrical, hydraulic or mechanical but usually in this case it is a non-electrical one. Different configurations are possible and the paper provides a timeline of the development of such powertrains with various examples. These types of hybrid vehicles have existed as prototypes for many decades and the authors believe that their development has reached levels where they can be considered serious contenders for production vehicles.