Fatigue strength assessment including welding residual stress of spot welded joints subjected to cross-tension loads

This paper presents a method to assess of fatigue strength for resistance spot welded joints, which incorporates welding residual stress effects. To achieve this, first, a non-linear finite element analysis (FEA) was performed to simulate the spot-welding process. To validate the FEA results, the numerically calculated welding residual stresses of spot welds were then compared with experimental results measured by X-ray diffraction method. The residual stress distributions showed good agreement between calculations and experiments. To evaluate the effects of welding residual stress on the fatigue design criterion of resistance spot welded joints subjected to cross-tension load, the stress amplitude (σ_a-res) taking into account welding residual stress at a spot weld was proposed based on a modified Goodman equation incorporating the residual stress effect. Using the stress amplitude σ_a-res at the nugget edge of a spot weld, the ΔP ? N_f relations obtained as the fatigue test results for spot welded joints were systematically rearranged to the σ_a-res ? N_f relation. It was found that the proposed stress amplitude (σ_a-res) provides more reasonable and accurate fatigue design criterion of spot welded joints subjected to cross-tension load.     

Urea-SCR system optimization with various combinations of mixer types and decomposition pipe lengths

The demand for NO_x after-treatment system has increased dramatically due to the stricter NO_x emission regulations for diesel vehicles. The urea-SCR system is one of the NO_x after-treatment methods found to be quite effective to meet the regulation requirement enforced by various authorities including the Euro-6. In order to develop an effective urea-SCR system, it is critical to establish an even distribution of reductant over the catalyst surface since this favorable distribution can increase reduction reaction and in turn, improve NO_x conversion efficiencies. In the current study, a number of design variations of the urea-SCR system which included two mixer types and three decomposition pipe lengths, were evaluated systematically using CFD analysis and experimental measurements. The purpose of the CFD analysis was to estimate the distribution of reductant within the urea-SCR system with a specific configuration and the purpose of the engine emission test was to measure the amount of NO_x reduction, respectively. The results from the systematic analysis revealed the relation between the reductant distribution over the SCR and the performance of the NO_x reduction.     

Evaluation and visualization of stratified ultra-lean combustion characteristics in a spray-guided type gasoline direct-injection engine

To comply with reinforced emission regulations for harmful exhaust gases, including carbon dioxide (CO₂) emitted as a greenhouse gas, improved technologies for reducing CO₂ and fuel consumption are being developed. Stable lean combustion, which has the advantage of improved fuel economy and reduced emission levels, can be achieved using a sprayguided-type direct-injection (DI) combustion system. The system comprises a centrally mounted injector and closely positioned spark plugs, which ensure the combustion reliability of a stratified mixture under ultra-lean conditions. The aim of this study is to investigate the combustion and emission characteristics of a lean-burn gasoline DI engine. At an excess air ratio of 4.0, approximately 23% improvement in fuel economy was achieved through optimal event timing, which was delayed for injection and advanced for ignition, compared to that under stoichiometric conditions, while NO_x and HC emissions increased. The combustion characteristics of a stratified mixture in a spray-guided-type DI system were similar to those in DI diesel engines, resulting in smoke generation and difficulty in three-way catalystutilization. Although a different operating strategy might decrease fuel consumption, it will not be helpful in reducing NO_x and smoke emissions; therefore, alternatives should be pursued to achieve compliance with emission regulations.     

Simulation of flow in diesel particulate filter system using metal fiber filter media

Metal fiber is introduced as a new filter media in wall-flow Diesel Particulate Filter (DPF) system. This technology has high temperature durability which is required for filter regeneration, and can maintain the mechanical strength even in the extreme exhaust-related vibrations of vehicles. However, the regeneration near the wall (outer layer) is more difficult because of the heat loss and reduced gas flow near the wall. In this study, a flow is simulated to determine the flow control method for the more uniform flow in all filter layer. By using Star CCM+ commercial software, we obtain local velocity, streamline, and pressure distributions in the filter, which are typically difficult to obtain from measurements. The major control factors are the filter porosity, size and location of the distribution plate, and the number of blades of the swirler. By placing the distribution plate in front of the filter, the flow velocity near the wall was increased. The optimum location and size of the flat plate were chosen. By attaching the blade on the plate the flow velocity near the wall was increased more. Therefore, the regeneration efficiency is increased by using the swirler-type metal fiber DPF system.     

Analysis of the shifting behavior of a novel clutchless geared smart transmission

Conventional geared transmissions use some kinds of clutches to control the power flow from an internal combustion engine to the driveline while shifting gears. However, the shifting performance is seriously affected by the clutch engagement and an unavoidable drop in the torque may occur when the clutch is disconnected. Moreover, wear of the clutch, the need for hydraulic equipment, and the load limit may together aggravate the limits of the clutch system. For this reason, as a novel transmission without a clutch, the clutchless geared smart transmission (henceforth CGST) is proposed by our research team. The CGST controls the power flow in a multiple-input gear-train by controlling the electric motor attached to the planetary gear system. However, no CGST has been realized in an actual vehicle thus far, and the performance has been predicted only theoretically. In this research, we analyzed the achievable performance based on a developed CGST dynamic model with a typical CGST structure. In addition, a CGST gear-shifting algorithm is proposed for use with the dynamic model. From the simulation results, the CGST does not show an abrupt drop in its torque or oscillation while shifting gears due to the absence of a discontinuous power flow. The developed dynamic model can serve as a performance reference for the CGST. Moreover, it can be used as a simulation tool for developing a gear-shifting control logic scheme.     

Improvement of long-term lives of rubber gaskets of polyacrylate (ACM) by employing carboxyl cure sites

Rubber gaskets are used widely in many industries. An evaluation of the material properties and an accurate lifetime prediction of rubber are very important in the design process to ensure the durability and reliability of rubber components. The properties of rubber-like materials are sensitive to ambient conditions, such as temperature, environment and mechanical load. Moreover, the initial properties of rubber gaskets must be sustained under working conditions to maintain its sealing function. To perform tests within a reasonable time, the highly accelerated life test (HALT) is generally used to predict the long-term lifetime of rubber materials. Polyacrylate (ACM) with chlorine cure sites is generally used for engine head gaskets. An ACM with carboxyl cure sites was developed to improve the lifetime of the gaskets. A four-parameter method representing the recovery behavior of the gaskets was published recently, and two revised methods for obtaining the recovery were proposed. The mean squared errors (MSEs) of the regression methods and experimental data were compared. The life of a gasket for the target recovery (60%) of a compressed gasket was calculated somewhat differently depending on the selected regression model to predict a considerably different long-term life. The parameters in the regression models were obtained using the successive zooming genetic algorithm (SZGA), and the lives of ACM with a carboxyl cure site and ACM with a chlorine cure site were compared.     

Deep foundation pit excavation procedure optimization considering creep deformation on nearby metro tunnelEI北大核心

Research purposes: The existing researches about excavating procedures of deep foundation pit on nearby metro tunnel in soft formation are lack of systematicness, and creep characteristics of soft clay are not usually taken into consideration. This paper takes Qianhaiwan station of Metro Line 11 in Shengzhen as engineering background and considers creep characteristics in sludge formation. The influence of step excavation in the transversal, longitudinal and vertical directions on the deformation of foundation pit and nearby subway tunnel are simulated, which may be expected to provide theoretical basis for choosing foundation pit excavation procedure of Qianhaiwan station. Research conclusions: (1) The segment far away from tunnel should be excavated firstly when only transversal step excavation was undertaken along the horizontal direction of foundation pit. (2) The maximum horizontal displacement of the piles show exponential relations with the number of segments when step excavation of foundation pit was undertaken in vertical and transversal or longitudinal. If thickness of every step excavation was limited in 1.5~2 m, the horizontal displacement of the pile near tunnel can be reduced about 9 percent when there is no horizontal step excavation. (3) Transversal step excavation with segments far from tunnel excavated firstly was found to be the best step excavation method under the same condition of step number and support, and longitudinal and transversal step excavation followed while longitudinal step excavation was the last. (4) The research results have guiding significance for foundation pit of Qianhaiwan station and similar projects.     

Construction Risk Management for Deep Excavation Adjacent to In operation Bored Tunnels

营运中的盾构隧道在邻近施工时周围地盘的应力可能因扰动而重新分布,使得盾构隧道暴露在因变形或位移衍生的结构损坏或营运中断等高风险下。为降低相关风险发生的可能性或后果的严重性,高雄计划将高雄车站段地下化工程捷运-R11永久站施工纳入风险管理,通过风险辨识、分析、评估以及以监测、巡检及沟通为基础的风险追踪查核等手段执行风险管理。依本计划执行成果,位于基地两侧营运中的盾构隧道在永久站主体工程开挖施工期间,各项风险均受到妥善的追踪、管控及处置。     

TBM掘进数据标准化预处理方法研究北大核心CSCD

TBM信息化采集了海量数据,对TBM数据的标准化预处理是进行诸多研究的前提。基于此,提出了一种TBM掘进数据标准化处理方法,依托TBM现场施工掘进大数据,以破岩特征为依据选取基本掘进参数(刀盘转速、推进速度、刀盘推力及刀盘扭矩)分析掘进过程TBM数据特点,提出循环掘进过程空推段、上升段、稳定段及下降段起点的判别方法,对稳定段起点提出了标准差法判别方法、均值判别方法、直方图判别方法,满足实时和非实时的数据划分需求。最后对两个TBM工程的数据进行标准化预处理,实现施工大数据的标准化。结果表明,提出的标准化预处理方法可实现循环掘进过程数据的有效划分。研究成果可推广应用于众多TBM工程的数据标准化处理,有效实现机器学习数据库的建立。