Shape Optimization of Elliptical Road Containers Due to Liquid Load in Steady-State Turning

A numerical analysis of liquid load in elliptical road containers undergoing a steady-state turning manoeuvre is presented for containers of unrestricted size and for containers of fixed capacity. The liquid load is expressed in terms of the horizontal and vertical forces and the overturning moment created by these forces around the middle bottom point of the container. The moment is obtained by integrating the liquid free-surface equation and using numerical calculation of the resulting expressions. An optimization study with an objective to minimize the peak overturning moment is performed on containers of fixed capacity to identify the optimal height/width ratio of the container. The results of this investigation being of a general nature, i.e. with no restriction for an application, are particularly intended for road tankers under a steady turning manoeuvre, where they can be applied with high degree of accuracy.     

Transit assignment under crowded conditions

This paper presents a transit assignment algorithm for crowded networks. Both congestion in vehicles and queuing at stations are explicitly taken into account in predicting passenger flows for a fixed pattern of origin-destination trip demands. The overflow effects due to insufficient capacity of transit lines are considered to be concentrated at transit stations, while the in-vehicle congestion effects (or discomforts) are considered to be dependent on in-vehicle passenger volume. Overflow delay at a transit station is dependent on the number of excess passengers required to wait for the next transit car. We use a logit model to determine the split between passengers that chose to wait for the next transit car and passengers that chose to board on the alternative transit lines. The proposed algorithm predicts how passenger will choose their optimal routes under both queuing and crowded conditions.     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

A study of passenger discomfort measures at the Hong Kong mass transit railway system

This note investigates the important attributes relating to the crowding effects at the Mass Transit Railway (MTR) stations in Hong Kong. Data was collected at two sets of three MTR stations to study the responses of the passengers due to the discomfort at crowded vehicles and platforms. Stated preference surveys were used to study the effects of passenger discomfort measures.     

Analysis of Driver's Decelerating Strategy in a Car-following Situation

This report describes a decelerating driver-model expressed by driving mode transition in car-following situations. The assumptions for constructing the model are that decelerating strategy of a driver is classified into several simple driving modes and that a driver changs his driving modes based on his perceptible characteristics and experiential rules. Deceleration action is divided into three states; following, standing and braking, which are applied to the model. The model has two paths for driver's decelerating action, one of which is selected by the driver based on the perceptible characteristics and experiential rules. The suitability of the model has been experimentally verified.     

Driver requirements and road traffic informatics

Initially the driver's role as a link in the driver-vehicle-road-traffic control-chain is discussed in a historical perspective. The gradual changes and the advantages and problems arising from these changes are discussed from behavioural point of view.Then the driver tasks are analyzed. A separation is made between trip planning, navigation, road following, traffic interaction, rule compliance, other than traffic tasks, car handling and speed choice. The relations between and the weights of these subtasks are discussed. Some existing driver behaviour models are reviewed in relation to the above mentioned tasks.Finally an effort is made based on the analyses of driver tasks and driver models to specify some general and some more specific potential advantages and problems with expected future RTI-systems.     

The design of bus route systems — An interactive location-allocation approach

An interactive modelling approach is developed to solve the practical problem of bus route network design. Possible bus routes are identified with facilities which can be located. Zones or pairs of zones in the urban area are identified with customers who will be allocated to the established facilities. It is shown that the classical Set Covering Problem is useful under the assumption of fixed demand; the Simple Plant Location Problem is effective under the assumption of demand which is sensitive to the level of bus service provided.     

A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

Regulatory reform and freight mode choice

Reform of trucking Vehicle Weights and Dimensions (VWD) regulations in Canada is now underway. The effect these reforms will have on the freight transportation industry are only recently the subject of research. This paper is part of this new research effort, aimed at understanding how regulatory reform in the trucking sector will affect the existing competitive relationship between trucks and the railways. The paper presents the results of study and research into modelling the relationship between mode choice and the service characteristics that are affected by VWD reform.Using several periods of data, a series of econometric models are developed which help to elucidate the relative relationships between the mode service characteristics for both of the principal interprovincial freight modes. A technique is developed and presented to model railway user costs in order to overcome the complex and often unrepresentable pricing activities of Canadian railways.The strength of the developed econometric models is presented, including their significance and statistical reliability. This is further reinforced by the similarities exhibited by all the models in the series. The selected model is applied to predict market service responses required of the railway industry in order to compete with the trucking sector now adapting to the new regulations.The impact of the newly implemented vehicle weight and dimension reform on the rail transportation industry is analyzed and railway industry improvements aimed at maintaining its market share are presented. The results predicted by the model show that railway user cost reductions should be moderate, and likely less than the level of inflation over the period of time when trucking converts its fleet to take advantage of the new regulations.Abbreviations AASHTO American Association of State Highway and Transportation Officials - CCMTA Canadian Conference of Motor Transport Administrators - EPI End products, inedible commodity classification - GVW Gross Vehicle Weight - NA 1988 VWD National Agreement - RTAC Roads and Transportation Association of Canada - VWD Vehicle Weight(s) and Dimension(s) - WA 1988 VWD Western Agreement