A container terminal simulation model with animation capabilities

The objective of this paper is to introduce a computer simulation model with on-screen animation graphics, which can simulate the operations of a container terminal equipped with straddle carriers. The movements of the equipment are simulated as realistically as possible, to include time losses due to the mismatch in the sequence of equipment movements and to traffic congestion. Trucks are normally served in a specified area, but in some cases, straddle carrier drivers can call the truck to be served directly in the container storage areas. The experience of operators is incorporated in the model, in the form of a knowledge base, that is used to simulate the above process and determine the service discipline. The model was designed to evaluate different configurations (changes in yard layout, equipment number and productivity, truck arrival pattern and service discipline) of the simulated system. The proposed model was used to examine the differences between “the observed” operations strategy and the strategy dictated by the operational rules of the port of Piraeus. The results indicate that “the observed” strategy leads to shorter truck service time but increase the traffic conflicts in the terminal's internal transport networks.     

Force Control in Electrohydraulic Active Suspensjons

For a simple vehicle active suspension system complete optimality and zero steady state body displacements may be achieved if the axle and body accelerations, and other easily measured quantities, are included in the performance index. Apart from not requiring an observer, this also allows the optimal feedback gains to be determined for an arbitrary body spring rate. In a theoretical example, model parameters matching those of an experimental test rig are employed. The results of computer simulations, with and without an electrohydraulic servovalve and actuator, are compared to demonstrate the effects of inner loop gain on force control. Aspects of the system behaviour including lockup are commented upon.     

Physically Realisable Feedback Controls for a Fully Active Preview Suspension Applied to a Half-Car Model

An optimal preview type active suspension with feedback control based on easily measured relative displacements, velocities and accelerations is proposed. Measurements relative to the road, except by the preview sensor, are not required and the front and rear spring rates are quite arbitrary. Also, state estimators or observers are unnecessary and as a practical alternative the body accelerometers may be replaced by load cells. The effects of preview on the performance, for a theoretical step type road input and an analogous random road input, are described. The definition of the optimum preview function, and its consequent effects on performance, receives attention and an example is given.     

Robust Scalable Vehicle Control via Non-Dimensional Vehicle Dynamics

A temporal and spatial re-parameterization of the linear vehicle Bicycle Model is presented utilizing non-dimensional ratios of vehicle parameters called p-groups. Investigation of the p-groups using compiled data from 44 published sets of Vehicle Dynamics reveals a normal distribution about a line through p-space. The normal distribution suggests numerical-values for an 'average' vehicle and maximum perturbations about the average. A state-feedback controller is designed utilizing the p-space line and the expected p-perturbations to robustly stabilize all vehicles encompassed by the normal distribution of vehicle parameters. Experimental verification is obtained using a scaled vehicle.     

The Influence of In-Plane Tyre Dynamics on ABS Braking of a Quarter Vehicle Model

For efficient analysis it is important to choose the proper model that fits the problem that needs to be solved. This paper discusses three pragmatic simulation models for longitudinal behaviour of a passenger car tyre (Steady State, Transient and Rigid Ring) that may be used in e.g. an ABS simulation. The characteristics of the simulation models are evaluated using some simple simulations. Simulations with a quarter vehicle model that includes load transfer effects are carried out to determine the deviation in results between the mentioned tyre models for an ABS application. The results show that the Steady State model may only be used below 10 Hz and that the Transient model is valid up to about 30 Hz. The results from the ABS simulation with the Rigid Ring model are most reliable and are clearly different from the Steady State and Transient model, which indicates that ABS simulations should be carried out with the Rigid Ring model. Additionally it is demonstrated that for tyre behaviour on uneven roads the influence of the tyre belt cannot be neglected.     

Optimal Control of a Vehicle Suspension Incorporating the Time Delay between Front and Rear Wheel Inputs

An optimal control law for a vehicle suspension is developed using a discrete linear quadratic regulator framework. The time delay between the disturbance due to the road at the front and rear wheels is incorporated into the model, and it is shown that the optimal control law requires information gathered at the front wheels. A comparison is made between the optimal control law and a suboptimal one which does not incorporate front wheel road information.     

Analysis of Metropolitan Highway Capacity and the growth in vehicle miles of travel

A number of recent studies have examined the hypothesis of induced travel in an attempt to quantify the phenomenon (Hansen & Huang 1997; Noland, forthcoming). No study has yet attempted to adjust for potential simultaneity bias in the results. This study addresses this issue by the use of an instrumental variable (two stage least squares) approach. Metropolitan level data compiled by the Texas Transportation Institute for their annual congestion report is used in the analysis and urbanized land area is used as an instrument for lane miles of capacity. While this is not an ideal instrument, results still suggest a strong causal relationship but probably that most previous work has had an upward bias in the coefficient estimates. The effect of lane mile additions on VMT growth is forecast and found to account for about 15% of annual VMT growth with substantial variation between metropolitan areas. This effect appears to be closely correlated with percent growth in lane miles, suggesting that rapidly growing areas can attribute a greater share of their VMT growth to growth in lane miles.