防止脱轨的新策略

介绍了防止脱轨的有效策略，并着重对脱轨原因分析方法以及技术进步对脱轨原因调查所起的积极帮助作用等进行了阐述。运用实践证明，早期发现是防止脱轨的关键，而一个具有系统性的总体方案，以及具有责任心的专业人员或专业队伍，则是成功的脱轨原因查找及其改进方案的根本所在。     

Updating of Travel Behavior Model Parameters and Estimation of Vehicle Trip Chain Based on Plate Scanning

This article proposes a maximum-likelihood method to update travel behavior model parameters and estimate vehicle trip chain based on plate scanning. The information from plate scanning consists of the vehicle passing time and sequence of scanned vehicles along a series of plate scanning locations (sensor locations installed on road network). The article adopts the hierarchical travel behavior decision model, in which the upper tier is an activity pattern generation model, and the lower tier is a destination and route choice model. The activity pattern is an individual profile of daily performed activities. To obtain reliable estimation results, the sensor location schemes for predicting trip chaining are proposed. The maximum-likelihood estimation problem based on plate scanning is formulated to update model parameters. This problem is solved by the expectation-maximization (EM) algorithm. The model and algorithm are then tested with simulated plate scanning data in a modified Sioux Falls network. The results illustrate the efficiency of the model and its potential for an application to large and complex network cases.     

Independent control of all-wheel-drive torque distribution

The sophistication of all-wheel-drive (AWD) technology is approaching the point where the drive torque to each wheel can be independently controlled. This potentially offers vehicle handling enhancements similar to those provided by dynamic stability control, but without the inevitable reduction in vehicle acceleration. Independent control of AWD torque distribution would therefore be especially beneficial under acceleration close to the limit of stability. A vehicle model of a typical sports sedan was developed in Simulink, with fully independent control of torque distribution. Box-Behnken experimental design was employed to determine which torque distribution parameters have the greatest impact on the vehicle course and acceleration. A proportional-integral control strategy was implemented, applying yaw rate feedback to vary the front-rear torque distribution and lateral acceleration feedback to adjust the left-right distribution. The resulting system shows a significant improvement over conventional driveline configurations under aggressive cornering acceleration on a high-μ surface. The performance approaches the theoretical limit for these conditions. In the medium term, such a system is only likely to be economically viable for premium vehicles. However, a future revolution of powertrain technology towards, for example, wheel-mounted motors, could realize these handling benefits far more widely.     

英国利用测速相机治理超速的方案

英国通过“安全相机方案”把自动测速相机成功地用于违章执法来改善道路安全,其核心是“以罚养查”。全面介绍了英国安全相机方案’的实践和程序。其设计理念和过去几年实践的经验对中国的超速治理有较高的借鉴价值。     

Novel evaluation method of fuel consumption and emission for heavy-duty hybrid electric vehicles

This paper is a continuation of a previous paper titled “A novel way to calculate energy efficiency for rechargeable batteries” published on Journal of Power Sources/2012 describing a new method to calculate energy efficiency for rechargeable batteries. The present paper further describes the application of energy efficiency model on the evaluation of fuel consumption and emission for the heavy-duty hybrid electric vehicles (HD-HEVs). A more accurate calculation method of net energy change for power battery pack is proposed based on energy efficiency model of power battery pack. A more simplified and accurate correction method of fuel consumption and emission is also presented based on equivalent mileage. The fuel consumption and emission on chassis dynamometer are measured in the HD-HEVs. The experiment results show that relative errors of fuel consumption and emission between equivalent mileage correction results and linear regression correction results are less than 3%, which verifies accuracy and validates the proposed evaluation method for HD-HEVs fuel consumption and emission.     

Crashworthiness design based on a simplified deceleration pulse

This paper proposes a procedure to improve the design of an automobile crashworthiness using the deceleration pulse in a simplified form as a design variable. A complete vehicle in a full frontal crash was simulated to find its deceleration pulse by finite element method. Based on this deceleration pulse, sled tests were performed, also in a virtual environment. Comparisons between the real deceleration pulse and a simplified pulse were made based on the HIC₁₅ produced. The simplified pulse is developed by dividing the pulse in three phases, each with a constant level of deceleration. Simulations were made to minimize the HIC₁₅ changing parameters in the restraint system and in the deceleration pulse. An expression was found to relate HIC₁₅ and the first phase of the deceleration pulse. A design case using this expression is presented. The benefits of using the pulse as a design variable along with the restraint system are accounted.     

De l’intérêt de contrôler l’impact des hypothèses de composition du parc automobile sur l’estimation des émissions liées au trafic routier

Since the 1990s, transport project assessments take systematically pollutant emission estimations into account. This paper is about the methodological aspects of these calculations. It focuses more specifically on the car fleet hypothesis, which most often lays on national data, without consideration of local specificities. We use the last household travel survey from Lyon, 2006, and the SIMBAD model to compare the results of CO₂ and NO_x emissions estimated from the French national car fleet, the aggregated Lyon car fleet and the same fleet disaggregated by household location and income. We show that the error level varies, depending on the pollutant and the observation scale. The use of an aggregated local car fleet seems interesting and satisfactory for a global emission assessment. If the results are required at a more detailed spatial level, the use of this local fleet improves sharply the estimations in comparison of a national fleet; the fleet disaggregation refines the results for NO_x.     

Optimization of intake port design for SI engine

It is well known that in-cylinder flow is very important factor for the performance of SI engine. An appropriate in-cylinder flow pattern can enhance the turbulence intensity at spark time, therefore increasing the stability of combustion, reducing emission and improving fuel economy. In this paper, the effect of intake port design on in-cylinder flow is studied. It is found a vortex existed at the upper side of intake port of a production SI engine used in the study, during the intake stroke, which will reduce both tumble ratio and volumetric efficiency. A minor modification on intake port is made to eliminate the vortex and increase tumble ratio while keeping volumetric efficiency at the same level. It is demonstrated that the increase in tumble in the new design results in a 20 per cent increase in the fuel vaporization. In this study, both KIVA and STAR-CD are used to simulate the engine cold flow, as well as ICEM CFD and es-ice used as pre-processor respectively due to the complexity of engine geometry. Simulation results from KIVA and STAR-CD are compared and analyzed.     

Real-time weighted multi-objective model predictive controller for adaptive cruise control systems

In this paper, a novel spacing control law is developed for vehicles with adaptive cruise control (ACC) systems to perform spacing control mode. Rather than establishing a steady-state following distance behind a newly encountered vehicle to avoid collision, the proposed spacing control law based on model predictive control (MPC) further considers fuel economy and ride comfort. Firstly, a hierarchical control architecture is utilized in which a lower controller compensates for nonlinear longitudinal vehicle dynamics and enables to track the desired acceleration. The upper controller based on the proposed spacing control law is designed to compute the desired acceleration to maintain the control objectives. Moreover, the control objectives are then formulated into the model predictive control problem using acceleration and jerk limits as constrains. Furthermore, due to the complex driving conditions during in the transitional state, the traditional model predictive control algorithm with constant weight matrix cannot meet the requirement of improvement in the fuel economy and ride comfort. Therefore, a real-time weight tuning strategy is proposed to solve time-varying multi-objective control problems, where the weight of each objective can be adjusted with respect to different operating conditions. In addition, simulation results demonstrate that the ACC system with the proposed real-time weighted MPC (RW-MPC) can provide better performance than that using constant weight MPC (CW-MPC) in terms of fuel economy and ride comfort.     

Circuit racing,track texture,temperature and rubber friction

ABSTRACT

Some general observations relating to tyre shear forces and road surfaces are followed by more specific considerations from circuit racing. The discussion then focuses on the mechanics of rubber friction. The classical experiments of Grosch are outlined and the interpretations that can be put on them are discussed. The interpretations involve rubber viscoelasticity, so that the vibration properties of rubber need to be considered. Adhesion and deformation mechanisms for energy dissipation at the interface between rubber and road and in the rubber itself are highlighted. The enquiry is concentrated on energy loss by deformation or hysteresis subsequently. Persson's deformation theory is outlined and the material properties necessary to apply the theory to Grosch's experiments are discussed. Predictions of the friction coefficient relating to one particular rubber compound and a rough surface are made using the theory and these are compared with the appropriate results from Grosch. Predictions from Persson's theory of the influence of nominal contact pressure on the friction coefficient are also examined. The extent of the agreement between theory and experiment is discussed. It is concluded that there is value in the theory but that it is far from complete. There is considerable scope for further research on the mechanics of rubber friction.