A repeated cross-sectional evaluation of car ownership

This paper studies changes in the relationship between household car ownership and income by household type. Ordered response probit models of car ownership are estimated for a sample of households repeatedly at six time points to track the evolution of income elasticities of car ownership over time. Elasticities of car ownership are found to change over time, questioning the existence of a unique equilibrium point between demand and supply that is implicitly assumed in traditional cross-sectional discrete choice car ownership models. Moreover, different household types and households that underwent household type transitions showed differing patterns of change in elasticities. Observed trends in car ownership and income clearly show behavioral asymmetry where the elasticity of procuring an additional car is greater than that of disposing a car. This too shows the inadequacy of traditional cross-sectional models of car ownership which tend to predict symmetry in behavior. The study suggests the importance of incorporating dynamic trends into the forecasting process, which can be accomplished through the use of longitudinal data.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

New lead-acid battery management system based on generator regulation

A novel regulation system for a vehicle generator and lead-acid battery is proposed in this paper. By integrating the regulation method, the output voltage of the generator is determined and controlled by the algorithm to save electrical energy and protect the lead-acid battery. The regulation algorithm is implemented in Matlab/Simulink, and the logic function of the system is verified using the dSPACE/AutoBox workbench. The experimental results show that the new algorithm improves the performance of the fuel economy of the vehicle and the battery state-of-health compared to the traditional control method.     

Comparison of the optimum designs of center pillar assembly of an auto-body between conventional steel and ahss with a simplified side impact analysis

This study compares the optimum designs of center pillar assembly with advanced high-strength steel (AHSS) to that of conventional steel for crashworthiness and weight reduction in side impacts. A simplified side impact analysis method was used to simulate the crash behavior of the center pillar assembly with efficient computing time. Thickness optimization aims to perform an S-shaped deformation of the center pillar toward the cabin to reduce the injury level of a driver in a crash test. Center pillar members were regarded as an assembly of parts that are fabricated with tailor-welded blanks, and the thickness of each part was selected as a design variable. The thickness variables of parts that have significant effects on the deformation mechanism were extracted as the main design variables for thickness optimization based on the results of a sensitivity analysis with design of experiments. The optimization condition was constructed to induce an S-shaped deformation mode and reduce the weight of the center pillar assembly. An optimum design was obtained after several iterations with response surface methodology (RSM). Optimization was first performed with conventional steel and then with AHSS with the same procedure to optimize the crashworthiness of the center pillar assembly. After thickness optimization, optimum designs were applied to the full vehicle analysis to evaluate the validity of the optimization scheme with the simplified side impact analysis method. Then, the crashworthiness of optimum designs with conventional steel and AHSS were compared using the full vehicle analysis. This comparison demonstrates that AHSS can be more effectively utilized than conventional steel to obtain a lightweight design of an auto-body with enhanced crashworthiness.     

Numerical simulation on truncated oval-nosed projectile penetrating into stiffened plate北大核心CSCD

[Objectives]In this paper, the numerical simulation method is used to study the anti-penetration performance and energy absorption mode of a stiffened plate, as well as the influence of different stiffened bars on the flight attitude of the projectile body.[Methods] Finite element software LS-DYNA is used to simulate the process of a truncated oval-nosed projectile penetrating a stiffened plate, and the results of the numerical simulation are compared with an experiment to verify the reliability of the numerical simulation method. The momentum method and mass equivalence method are used to predict the residual velocity of the projectile, and the applicability of different theoretical methods within different velocity ranges is compared. The deformation energy of different regions of the stiffened plate is then extracted to analyze the influence of the initial velocity of the projectile body on the energy absorption mode of the target plate. Finally, the structure of the stiffeners is changed and the influence of the relative position of the stiffeners on the penetration attitude of the projectile body is analyzed.[Results]The results show that the mass equivalence method is more accurate than the momentum method in predicting the residual velocity of the stiffened plate when the initial velocity of the projectile body is in the range of 300–900 m/s. The ratio of the deformation energy of the stiffened plate to the energy loss of the projectile body decreases with the increase of the initial velocity of the projectile body. The effect of a T-stiffened plate on trajectory is greater than that of a rectangular-stiffened plate.[Conclusions]The related calculation method and research results have certain reference value for research and engineering application surrounding the anti-penetration of stiffened plates. © 2023 Chinese Journal of Ship Research. All rights reserved.     

襄阳汉江沉管隧道设计关键技术北大核心CSCD

基于襄阳汉江沉管隧道的工程设计实践,针对该隧道强冲刷、强透水地层深厚、防洪要求高等特点,对隧道平纵布置、管节及接头止水结构、干坞选型及结构、沉管基础及回填、沉管最终接头及对接端止水结构等进行了研究。结果表明:(1)内河沉管隧道采用长距离双轴线干坞布置方式,通过格形地下连续墙、超深落底式帷幕、地下连续墙预应力锚索垂直支护和混凝土封底组合技术解决了强透水地层深基坑支护及隔水难题;(2)采用全断面顺浇技术进行整体式管节预制,实现了管节接头止水设施的全国产化;(3)在内河沉管隧道采用高精度浮式整平先铺卵石基础,并提出了强冲刷区管顶防冲保护解决方案;(4)采用了不设独立止推构造的陆域最终接头,并针对工程需求设置了大直径锁口钢管桩配合外侧止水墙的对接端支护结构及分片整体吊装双壁钢围堰二次止水结构。     

Galvanic corrosion behaviour of HE 20 / MDN 138 & HE 20 / MDN 250 alloys in natural seawater

In view of their excellent mechanical properties, workability and heat treatment characteristics, MDN 138 & MDN 250 have been widely used in missile, rocket and aerospace industries. With light weight and high performance characteristics HE 20 aluminium alloy acts as an important material in defence and aerospace applications. The galvanic corrosion behaviour of the metal combinations HE 20 / MDN 138 and HE 20 / MDN 250, with 1:1 area ratio, has been studied in natural seawater using the open well facility of CECRI’s Offshore Platform at Tuticorin for a year. The open circuit potentials of MDN 138, MDN 250 and HE 20 of the individual metal, the mixed potential and galvanic current of the couples HE 20 / MDN 138 and HE 20 / MDN 250 were periodically monitored throughout the study period. The calcareous deposits on MDN 138 and MDN 250 were analysed using XRD. The results of the study reveal that that HE 20 has offered required amount of protection to MDN 138 & MDN 250.     

Mathematical model for optimising the sequence for clearing snow from the manoeuvring area during winter operations

This article considers the optimisation of the sequence for clearing snow from stretches of the manoeuvring area of an airport. This issue involves the optimisation of limited resources to remove snow from taxiways and runways thereby leaving them in an acceptable condition for operating aircraft. The airfield is divided into subsets of significant stretches for the purpose of operations and target times are established during which these are open to aircraft traffic. The document contains several mathematical models each with different functions, such as the end time of the process, the sum of the end times of each stretch and gap between the estimated and the real end times. During this process, we introduce different operating restrictions on partial fulfilment of the operational targets as applied to zones of special interest, or relating to the operation of the snow‐clearing machines. The problem is solved by optimisation based on linear programming. The article gives the results of the computational tests carried out on five distinct models of the manoeuvring area, which cover increasingly complex situations and larger areas. The mathematical model is particularised for the case of the manoeuvring area of Adolfo Suarez Madrid—Barajas Airport. Copyright © 2016 John Wiley & Sons, Ltd.

Highlights
• Optimal sequence for clearing snow from the manoeuvring area of an airport.
• Contains optimising algorithms solved using CPLEX LP‐based tree search.
• Restrictions on partial fulfilment of operational targets applied to subsets of significant stretches, used for planning the operation of snow‐clearing machines.
• Model applied to the case of the manoeuvring area of Adolfo Suárez Madrid Barajas Airport.
• Conclusions are given on the results of the computational tests carried out. There are five models of the manoeuvring area which cover increasingly complex situations and larger areas.

     

耐碰撞车辆的撞击性能

对耐碰撞车辆列车的撞击性能作了分析研究,并编制了解析大型塑性变形的动力学模拟程序。对进一步改进耐碰撞车辆的设计进行了讨论。