Research on the Dust Removal Technology for Shield Tunnel Overhaul Construction北大核心CSCD

The shield tunnel is an ultra-long linear space. It will cause a lot of dust during the tunnel maintenance and overhaul operation, which is extremely unfavorable to the physical and mental health of the construction personnel and the environment outside the tunnel. It is difficult to guarantee the ventilation effect of the linear space using the conventional dust removal technology, which directly affects the construction safety and overhaul period. Therefore, based on the overhaul of a cross-river tunnel in Shanghai, combined with Computational Fluid Dynamics (CFD) simulation, device optimization and process combination, a three-stage dust reduction standardization process for tunnel overhaul construction is proposed, namely taking a water sprayer at the working point to control the dust at the source (primary protection); installing electrostatic dust removal and water filtration dust removal equipment in the tunnel(secondary protection); and installing two sets of water curtain spray device at the two tunnel exits to prevent dusts from diffusing into the atmosphere. It explores the actual dust-reducing effects of different dust-removing measures and layout combinations, laying a technical foundation for green and efficient dust reduction. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Experimental Study of the Tunnels with Natural Ventilation for Various Parameters of Ventilation Openings北大核心CSCD

In order to compare the ventilation efficiency and air speed of the tunnel for different parameters of ventilation openings, the acrylic board is used to build a 1:15 tunnel model and carry out the proportional model test. Four working conditions are set up to compare the ventilation in the tunnel under different ventilation openings in terms of number, length and height. The experimental results show that the air velocity distribution and ventilation efficiency change significantly under different ventilation openings in terms of number, length and height. Based on the test results, the best setting pattern of the ventilation opening is proposed in this paper. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Adaptation Pathways in Coastal Case Studies: Lessons Learned and Future Directions

Climate change adaptation presents a difficult challenge for coastal towns around the world, forcing local governments to plan for sea level rise in a contentious decision-making space. The concept of “adaptation pathways,” a diagnostic and analytical tool to assist in adaptive planning and decision-making, is gaining traction as a way of framing and informing climate adaptation. It provides decisionmakers a way to acknowledge the inter-temporal complexities and uncertainties associated with the novel dynamics of climate change and a mechanism to manage these challenges in the local context. In 2012, the Australian Government funded an 18-month program to provide decisionmakers in the coastal zone an opportunity to test the utility of the adaptation pathways concept for coastal climate adaptation. Using a selection of completed projects as case studies, we performed a document analysis to better understand the learnings from the projects. The main themes surrounded: (1) the utility of the adaptation pathway framework in developing options, (2) decision-making rationale and criteria, and (3) stakeholder participation in pathway development. A project participant survey was developed to further understand these themes. Our analysis reveals that “adaptation pathways” was generally framed narrowly and conservatively to emphasize extant economic, administrative and legal considerations over community, participatory, or exploratory ones. Although some case study projects were able to reach a point in the pathway discussion to actively involve stakeholders in their decision-making process, many case studies continued to build technical data as a method for defending policies and actions. These results indicate that coastal adaptation can take-up adaptation pathways as a useful concept for decision-making and planning; however, many councils may still require assistance in stakeholder communication processes in order to develop sociallyacceptable plans that take into account the full range of values affecting local coastal environments.     

Propeller torque load and propeller shaft torque response correlation during ice-propeller interaction

Ships use propulsion machinery systems to create directional thrust. Sailing in ice-covered waters involves the breaking of ice pieces and their submergence as the ship hull advances. Sometimes, submerged ice pieces interact with the propeller and cause irregular fluctuations of the torque load. As a result, the propeller and engine dynamics become imbalanced, and energy propagates through the propulsion machinery system until equilibrium is reached. In such imbalanced situations, the measured propeller shaft torque response is not equal to the propeller torque. Therefore, in this work, the overall system response is simulated under the ice-related torque load using the Bond graph model. The energy difference between the propeller and propeller shaft is estimated and related to their corresponding mechanical energy. Additionally, the mechanical energy is distributed among modes. Based on the distribution, kinetic and potential energy are important for the correlation between propeller torque and propeller shaft response.     

Reducing car dependence in the heart of Europe: lessons from Germany,Austria, and Switzerland

Munich, Berlin, Hamburg, Vienna, and Zurich – the largest cities in Germany, Austria, and Switzerland – have significantly reduced the car share of trips over the past 25 years in spite of high motorisation rates. The key to their success has been a coordinated package of mutually reinforcing transport and land-use policies that have made car use slower, less convenient, and more costly, while increasing the safety, convenience, and feasibility of walking, cycling, and public transport. The mix of policies implemented in each city has been somewhat different. The German cities have done far more to promote cycling, while Zurich and Vienna offer more public transport service per capita at lower fares. All five of the cities have implemented roughly the same policies to promote walking, foster compact mixed-use development, and discourage car use. Of the car-restrictive policies, parking management has been by far the most important. The five case study cities demonstrate that it is possible to reduce car dependence even in affluent societies with high levels of car ownership and high expectations for quality of travel.     

Minimal-revenue congestion pricing Part II: An efficient algorithm for the general case

The second of a two-part series, this paper derives an efficient solution to the minimal-revenue tolls problem. As introduced in Part I, this problem can be defined as follows: Assuming each trip uses only a path whose generalized cost is smallest, find a set of arc tolls that simultaneously minimizes both average travel time and out-of-pocket cost. As a point of departure, this paper first re-solves the single-origin problem of Part I, modeling it as a linear program. Then with a change of variable, it transforms the LP's dual into a simple longest-path problem on an acyclic network. The multiple-origin problem – where one toll for each arc applies to all origins – solves analogously. In this case, however, the dual becomes an elementary linear multi-commodity max-cost flow problem with an easy bundling constraint and infinite arc capacities. After a minor reformulation that simplifies the model's input to better accommodate output from common traffic assignment software, a solution algorithm is exemplified with a numerical example.     

Fatigue life prediction of welded stiffened 350WT steel plates

The propagation of fatigue cracks under constant amplitude cyclic loading was studied in welded stiffened steel plates. The residual stresses in the stiffened plates were measured using the neutron diffraction strain-scanning technique. A finite element model of the stiffened plate was constructed to simulate the residual stresses by an uncoupled thermal and thermo-mechanical analysis. Both the finite element model and the neutron diffraction measurements indicated that in general the residual stresses were tensile near the welded stiffeners and compressive between the stiffeners and ahead of the starter notch tip. Fatigue testing indicated that the fatigue crack growth rates of the stiffened plates were in general lower than that of a corresponding unstiffened plate, especially near the notch tip where compressive residual stresses existed. Both the finite element method and Green's function predicted the fatigue crack growth rates with reasonable accuracy.     

The economic impact of the ATA/Southwest Airlines code-share agreement

This paper examines the economic impact of the code-sharing agreement between ATA and Southwest Airlines, the first time Southwest has chosen to enter markets via a code-share alliance rather than direct entry. We examine the impact of complementary code-sharing on incumbent airline's fares and passenger volumes and also the overall impact on consumer welfare in Denver airline markets. Empirical results show that air fares decreased and passenger volumes increased for incumbent carriers operating on code-shared routes. Further, we find evidence that this code-sharing arrangement increased both consumer and producer surplus. Thus, the well-known “Southwest Effect” is observed not only when Southwest enters a route directly, but also when it enters a route via a code-share agreement with another airline.     

Experimental study of an electro-mechanical CVT ratio controller

This paper introduces an electro-mechanical, dual acting pulley, continuously variable transmission (EMDAPCVT) and presents its real time ratio controller using a proportional-derivative-plus-conditional-integral (PDPCI) controller. The ratio controller system is developed based on primary (input) and secondary (output) pulley position controllers. Each position controller has two PID parameters, releasing and clamping, which are determined experimentally using a relay feedback method. A PC-based ratio controller system is implemented using Matlab/Simulink® software and a Keithley DAS-1602 data acquisition system card. The experimental results show that the PDPCI controller system can control the CVT ratio adequately.