变质岩地区含碎石黏土边坡稳定性分析

在野外地质勘查工作基础之上,分析了南方变质岩地区含碎石黏土边坡的破坏机理,结合工程实例,运用极限平衡法计算边坡在此潜在破坏模式下的稳定性,同时运用有限元法对边坡的稳定性进行了模拟分析和评价,两种计算结果表明,该滑坡属于水压力驱动型滑坡,在降雨作用下会失稳破坏.同时对该边坡提出预应力锚索抗滑桩+排水沟综合治理方案.     

一种新型调车信号机灯丝转换报警电路

针对传统调车信号机灯丝转换报警电路存在不能实时监测副灯丝状态、报警显示不能精确到具体故障灯位等缺点,提出一种新型调车信号机灯丝转换报警方法。采用单片机作为中心控制器、电压互感器为监测元件、电压跟随器和反相比较器组成断丝信号处理电路、RS-485总线为报警信号传输电路。该方法与传统电路相比增加了灯丝暖丝电路、故障灯位显示和故障信号处理电路,提高电路性能,降低电路成本,增强电路的实用性。     

广佛线信号系统与屏蔽门系统接口分析

屏蔽门的控制需要信号提供相应的接口,以广州地铁广佛线为例描述了西门子CBTC信号系统和PSD系统之间的接口设计,介绍了CBTC信号系统与PSD的接口功能、电气接口和电气接口的操作。接口功能方面涉及CTC模式下的接口任务、联锁的接口任务和系统信息传递情况,电气接口方面提到各种运行状态下的继电器接口及简要分析了其工作原理及电路连接图,另外在接口操作方面还介绍了信号系统与PSD系统之间的开关门时序、开关门真值表和动作时间等内容。     

K1000型钢轨焊机推瘤刀激光熔覆修复研究

为修复已磨损的推瘤刀,利用正交实验,确定出熔覆试验最优激光功率、离焦量和扫描速度分别为1.6kW,20 mm和4mm·s-1;据此进行相关的激光熔覆修复实验.熔覆材料以Ni60自熔性合金粉末为主,随着碳化钨(WC)粉末质量分数的增大,熔覆层的平均显微硬度和相对耐磨性先增大后减小,当WC粉末的质量分数为25％时,熔覆层的平均显微硬度和相对耐磨性分别达到最大值648.7 HV和3.49;在Ni60自熔性合金粉末和WC粉末的混合物中加入稀土CeO2粉末后,熔覆层深度小于1.0mm部分的显微硬度明显提高,超过700HV,能够满足推瘤刀刃口处硬度为56HRC的要求;稀土CeO2粉末的添加量对熔覆层显微硬度的影响不大;当WC粉末和稀土CeO2粉末的质量分数分别为25％和1.5％时,熔覆层的磨损失重仅为3.4 mg.     

轨道交通“捆绑式”开发的新模式

在分析地铁项目亏损的原因后,认为“捆绑式”开发已成为解决地铁可持续发展的必由之路。通过分析香港“地铁＋地产”的开发模式,提出香港模式有其成功所必须依赖的政策、法规、规划、地域等条件,这些条件是内地暂时无法具备也不能克隆的。根据广佛地铁的特点,尝试探索一条符合国情特征的捆绑式开发的新模式：“地铁＋地产＋产业园”。     

新媒体环境下全地形车营销策略分析

互联网+和大数据技术的不断发展和进步让信息经济时代真正地到来了。伴随着电子商务从起步到发展,很多的电商运营平台也逐渐凸显出自己的价值和地位。与此同时,电子商务的营销模式也从传统的B2B、B2C模式向着O2O、C2B的方向发展。全地形车,是一种十分独特的车型,适用的范围和人群也具有特定性。为此,在新媒体的环境之下,如何进行全地形车的营销,如何能够为全地形车吸引到更多的受众群体,这正是本文所要探究的关键所在。为此,文章在对全地形车的基本内涵、主要分类进行阐述和分析以后,针对全地形车这一个特殊车型的营销模式的创新和进步,提出了一些见解和主张。     

FPSO上部模块支墩结构疲劳强度分析

模块支墩结构是上部模块与FPSO船体主甲板之间的连接结构,在模块支墩结构设计中除考虑上部模块自重、惯性力及风载等载荷,还应注意船体梁整体弯曲变形的影响,故在设计最初就应考虑支墩结构疲劳强度.该文通过对FPSO上部模块支墩结构的疲劳评估,基于线性疲劳累积损伤原理的简化疲劳评估方法,展开疲劳分析,并考虑了FPSO服役寿命周期内的各种工况,在此过程中借助有限元分析软件成功获得了疲劳评估中的重要数据.分析支墩结构疲劳损坏的危险区域及疲劳产生的主要诱因,分析结果可为后续支墩结构的详细节点设计提供借鉴.     

Micro-Grinding Performance of Hard-Brittle Chip Materials in Precision Micro-Grinding Microgroove

The micro-structure on hard-brittle chip materials (HBCMs) surface can produce predominant functions and features. The micro-grinding with diamond wheel micro-tip is an efficient method to machine microstructure on HBCMs. However, different HBCMs and crystal orientation may have a significant influence on the micro-grinding performance. In this paper, the micro-grinding performance along different crystal orientation of HBCMs is investigated. First, a dressed 600^# diamond grinding wheel is used to micro-grind micro-structure on HBCMs. Then, the experiment of micro-grinding force test is completed. Finally, the quality of microgroove, the grinding ratio and the micro-grinding force are investigated and they are related to the crystal orientation of HBCMs. It is shown that the stronger resistance to the micro-crack propagation has the best quality of microgroove and the smallest grinding ratio. Moreover, the hardest single-crystal SiC has the best machinability and the micro-grinding force is 38.9%, 10.8% and 46.8% less than the one of sapphire, single-crystal Si and quartz glass, respectively. The direction to micro-grind easily is the crystal orientation 〈10\(\overline 1 \)0〉 for single-crystal SiC and sapphire. In addition, the micro-grinding force increases with the increase of the micro-grinding depth and feed rate and decreases with the increase of the grinding wheel speed.     

The Reinforcement Analysis of Prestressed Anchor Frame Beam in the Deep Cutting Slope under Three Dimensional Strong EarthquakeEI北大核心

Research purposes: In order to further study the reinforcement of prestressed anchor frame beam in the deep cutting slope under three dimensional strong earthquake, a model of the deep cutting slope is built through FLAC 3D simulation software, the seismic wave to the model from three directions of x,y and z is input, and the dynamic response of the slope is analyzed. Then, the prestressed anchor frame beam reinforcement measures are applied to the model, and this paper analyzes the reinforcement effect of the prestressed anchor frame beam to the deep cutting slope under three dimensional strong earthquake. Research conclusions:(1) The prestressed anchor frame beam has a good effect on restraining the horizontal displacement of the deep cutting slope. (2) Under the three dimensional strong earthquake, the prestressed anchor frame beam has a good effect on the horizontal acceleration and horizontal velocity of the deep cutting slope, which reduces the peak of horizontal acceleration and horizontal velocity. (3) Through the comparison of the response before and after the reinforcement of the prestressed anchor frame beam is given under the 9 degrees three dimensional strong earthquake, it can be concluded that the prestressed anchor frame beam can provide good reinforcement effect to the deep cutting slope. (4) This research can be used for reference to the earthquake resistance of the slope engineering. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

基于工作流的新产品项目开发协同设计研究

针对本企业汽车配件新产品项目开发过程中出现的一些问题,建立了基于工作流技术的新产品项目开发协同设计管理模型。文中阐述了工作流技术的一些关键技术和算法,实现了汽车配件新产品开发项目管理的信息化。