Comparative analysis on dynamic behavior of two HMA railway substructures

A numerical analysis using a finite element program was performed on three structures:hot mix asphalt(HMA) reinforced trackbed(RACS-1),HMA directly supported trackbed(RACS-2),and traditional Portland Cement Concrete(PCC) slab track(SlabTrack).Although the comprehensive dynamic responses of RACS-1 were similar with SlabTrack,HMA layer can positively affect the stress distributions.In particular,the horizontal stresses indicate that the resilience of RACS-1 was improved relative to SlabTrack.In addition,HMA r...     

Combined experimental and modeling methodology for intake line evaluation in turbocharged diesel engines

This paper presents a methodology for diesel engine intake line analysis that combines specific element tests and modeling. The purpose of this methodology is to determine the impact of intake lines, or newly designed intake elements, on the volumetric efficiency of internal combustion engines while avoiding expensive on-engine tests. For this research, the intake system is divided into several elements which are individually characterized using flow and impulse test rigs. Next, individual systems are modeled using a one-dimensional code. Finally, these component models are coordinated to provide an evaluation of the volumetric efficiency. Intake lines coming from two turbocharged diesel engines are used to illustrate the method. The model is validated by comparing the model results with the actual system performance evaluated in engine test cells. Discussions of the feasibility of the technique and on the impact of element model inaccuracies on the overall system model are provided.     

Torque ripple minimization control of permanent magnet synchronous motors for EPS applications

This paper identifies a control method used to reduce torque ripple of a permanent magnet synchronous motor (PMSM) for an electric power steering (EPS) system. NVH (Noise Vibration Harshness) is important for safe and convenient driving. Vibration caused by motor torque is a problem in column type EPS systems. Maintaining a very low torque ripple is one solution that allows for smoother steering. Theoretically, it is possible to design and drive the motor without torque ripple. However, in reality, a PMSM system torque ripple is caused by the motor itself (saturation in the iron core and EMF distortion) and the imperfect driver. This paper analyzes torque ripple of a PMSM system, and an advanced PMSM control method for the column typed EPS system is presented. Results of the analysis indicate that the compensation current is needed in order to minimize torque ripple when a PMSM is driven.     

Optimal design of the exhaust system layout to suppress the discharge noise from an idling engine

At the idle engine speed, the exhaust discharge noise is influenced by resonances in the whole system, which is composed of connecting pipes and silencers. This pipe resonance radiates a high level of low frequency discharge noise, which is dominated by the low order harmonics of the engine firing frequency. This low frequency noise deteriorates the vehicle’s interior noise level and quality. The following study attempted to optimize the layout of an exhaust system to minimize low frequency noise by changing the position of silencers and the lengths of inlet and outlet pipes in each silencer. After modeling the exhaust system using four-pole parameters, the acoustical performance of the system was evaluated using the system insertion loss. In the optimization, the virtual attenuation coefficient, which corresponds to the amount of attenuation coefficient required for the silencers, was calculated to find a minimum value for the layout. The simulated annealing method, which is also known as finding an optimal, was employed in searching for the optimized exhaust layout. Test examples of two cases, for two and six design variables, were used. When the number of design variables was two, the positions of the center and rear silencers were considered. When the number of design variables was six, the positions of the two silencers and the lengths of the inlet and outlet pipes were considered. Three typical layouts for the exhaust system of each case were designed, including the given system and an optimal system. By comparing the predicted and measured discharge noise level, it was confirmed that the optimized exhaust layout has a higher noise reduction than the other layout designs.     

Design and use of an eddy current retarder in an automobile

In this study, the structure and working principles of an eddy current retarder acting as an auxiliary brake set is introduced in detail. Based on the principle of energy conservation, a mathematical model was developed to design a retarder whose nominal brake torque is 1, 900 N·m. According to the characteristics of the eddy current retarder, an exclusive test bed was developed and used for brake performance measurements. The main technical parameters, such as the brake characteristics, temperature characteristics and power consumption, were measured with the test bed. The test data show that the brake torque of the eddy current retarder obviously decreased in the continuous braking stage and that there is a certain amount of brake torque in the normal driving state because of the remnant magnetism of the rotor plate. The mathematical model could be used to design an eddy current retarder. The exclusive test bed could be used for optimization of an eddy current retarder as well as for R&D of a series of products.     

Nano-particle emission characteristics of European and Worldwide Harmonized test cycles for heavy-duty diesel engines

This study was conducted for the experimental comparison of particulate emission characteristics between the European and World-Harmonized test cycles for a heavy-duty diesel engine as part of the UN/ECE PMP ILCE of the Korea Particulate Measurement Program. To verify the particulate mass and particle number concentrations from various operating modes, ETC/ESC and WHTC/WHSC, were evaluated. Both will be enacted in Euro VI emission legislation. The real-time particle emissions from a Mercedes OM501 heavy-duty golden engine with a catalyst based uncoated golden DPF were measured with CPC and DMS during daily test protocol. Real-time particle formation of the transient cycles ETC and WHTC were strongly correlated with engine operating conditions and after-treatment device temperature. The higher particle number concentration during the ESC #7 to #10 mode was ascribed to passive DPF regeneration and the thermal release of low volatile particles at high exhaust temperature conditions. The detailed average particle number concentration equipped for golden DPF reached approximately 4.783E+11 #/kWh (weighted WHTC), 6.087E+10 #/kWh (WHSC), 4.596E+10 #/kWh (ETC), and 3.389E+12 #/kWh (ESC). Particle masses ranged from 0.0011 g/kWh (WHSC) to 0.0031 g/kWh (ESC). The particle number concentration and mass reduction of DPF reached about 99%, except for an ESC with a reduction of 95%.     

Assessment of IACS-CSR implicit safety levels for buckling strength of stiffened panels for double hull tankers

The present study aims at applying structural reliability methods to assess the implicit safety levels of the buckling strength requirements for longitudinal stiffened panels implemented in the IACS Common Structural Rules (CSR) for double hull oil tankers. The buckling strength requirements considered are used in the initial stage of the hull girder scantlings’ design to control the buckling capacity of longitudinal stiffened panels subjected to the compressive loads induced by the hull girder vertical bending. The following buckling collapse failure modes are explicitly considered in the design formulation: uniaxial buckling of the plating between stiffeners, column buckling of stiffeners with attached plating and lateral-torsional buckling or tripping of stiffeners.The paper presents the procedure used to assess the implicit safety levels of the strength requirements for the three buckling collapse failure modes above mentioned, which includes the optimization of the scantlings of the plate panels and longitudinal stiffeners in order to reflect the minimum strength required by the formulation. A first order reliability formulation is adopted, and stochastic models proposed in the literature are used to quantify the uncertainty in the relevant design variables. A sample of five oil tankers representative of the range of application of the IACS-CSR design rules is considered. The effect of corrosion in the implicit safety levels is quantified based on the three corrosion levels of the Net Thickness Approach (NTA) adopted in the design rules. Sensitivity analyses are also performed to quantify the relative contribution or importance of each design random variable to the implicit safety levels.     

Research on the management innovation and practice of construction for Beijing-Shanghai high speed railwayEI北大核心

Construction of Beijing-Shanghai high speed railway is unprecedented great feat. Around the construction goal of "world class", a series innovation and practice measures are taken in the construction ideas, organization and management, technology research, investment financing, quality, safety, investment, construction period, environmental protection, stability, and so on, to lay a solid foundation of completing Beijing-Shanghai high speed railway construction efficiently. In the current new situation of speeding up railway construction, systematically summarizing the results of management innovation and practice for Beijing-Shanghai high speed railway has very important practical significance to improve the level of railway construction project management in our country.     

Comparison of PMP and DP in fuel cell hybrid vehicles

Pontryagin’s Minimum Principle (PMP) and Dynamic Programming (DP) are both from the optimal control theory and can both achieve optimal trajectories when they are applied to power management strategies of hybrid vehicles. However they have totally different control concepts. In order to select the superior one, the PMP-based and the DP-based power management strategies are introduced and compared for a fuel cell hybrid vehicle (FCHV) in this paper. The two power management strategies are applied to the FCHV in a computer simulation environment, and the simulation results from the two strategies are compared when the control variable for the PMP is fuel cell system (FCS) net power and for the DP is battery power. As a result, the superiority of the PMP-based power management strategy is proved.     

Precise and reliable positioning based on the integration of navigation satellite system and vision system

In this paper, we propose a precise and reliable positioning method for solving common problems, such as a navigation satellite’s signal occlusion in an urban canyon and the positioning error due to a limited number of visible navigation satellites. This is an integrated system of the navigation satellites system and a vision system. In general, the navigation satellite positioning system has a fatal weakness in that it can not calculate a position coordinate when its signal is occluded by some obstacle. For this reason, positioning by using the navigation satellites system can not be used for a variety of applications. Therefore, we propose as a method to integrate both the navigation satellites system and the vision system. Some target objects that have accurate position coordinates, for example, in an outdoor shaded area like an urban canyon, are installed into the vision system. When the vision system recognizes a target object it loads the accurate coordinate of that target object. Then, it measures the distance by using the disparity from the camera sensor to the target object. These distance and object coordinate data are used for positioning with the navigation satellites system’s data. This integrated system can be used for the positioning solution where the user is in unfavorable conditions. This paper shows that the algorithm of integrated system and the numerical test performed. The results indicate that the reliable and stable positioning can be obtained by introducing the vision system to the satellite navigation system.