Simulation of a powertrain system for the diesel hybrid electric bus

The plug-in hybrid electric bus (HEB) is designed to overcome the vulnerable driving range and performance limitations of a purely electric vehicle (EV) and have an improved fuel economy and lower exhaust emissions than those of a conventional bus and convention HEBs. The control strategy of the plug-in parallel HEB??s complicated connected propulsion system is one of the most significant factors for achieving a higher fuel economy and lower exhaust emissions than those of the HEV. The proposed powertrain control strategy has flexibility in adapting to the battery??s state of charge (SOC), exhaust emissions, classified driving patterns, driving conditions, and engine temperature. Simulation is required to model hybrid powertrain systems and test and develop powertrain control strategies for the plug-in parallel HEB. This paper describes the simulation analysis tools, powertrain components?? models and modifications, simulation procedure, and simulation results.     

A Cooperative Intelligent Transport Systems (C‐ITS)‐based lane‐changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane‐change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane‐changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C‐ITS). This research investigates a lane‐change distribution advisory application based on C‐ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane‐changing concentration problem by coordinating weaving vehicles to ensure that such lane‐changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in aimsun to evaluate the proposed strategy's effectiveness in a one‐sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane‐changing advisory has the potential to significantly improve delay. Copyright © 2016 John Wiley & Sons, Ltd.     

Transfer demand prediction for timed transfer coordination in public transport operational control

Timed transfer coordination in public transit reduces passenger transfer time by providing seamless interconnected transfers. The problem arises when a Receiving Vehicle (RV) arrives to the transfer stop before a Feeding Vehicle (FV) carrying transferring passengers. Timed transfer coordination in operational control dynamically decides whether a RV is held at the transfer stop to allow transfers, or departs as scheduled. While transfer demand is essential for implementing timed transfer coordination, this variable is generally not available in public transit because of the lack of passenger transfer plans. The problem of acquiring this variable in real‐time has also received limited attention in the related literature. This paper proposes a new method to dynamically predict the transfer demand. We anticipate the transferring probability from each individual passenger by examining historical travel itineraries. Three different types of models (simple analytical, statistical, and computation intelligence model) are developed to forecast the number of transferring passengers. Numerical experiments using observed Automatic Vehicle Location and Automatic Fare Collection data from South East Queensland, Australia show the accuracy and applicability of the proposed models in timed transfer coordination. Copyright © 2017 John Wiley & Sons, Ltd.     

Queue discharge patterns at signalized intersections with green signal countdown device and long cycle length

Two apparent features that prevail at signalized intersections in China are green signal countdown device and long cycle lengths. The objective of this study is to investigate the impacts of green signal countdown device and long cycle length on queue discharge patterns and to discuss its implications on capacity estimation in the context of China's traffic. At five typical large intersections in Shanghai and Tianjin, 11 through lanes were observed, and 9251 saturation headways were obtained as valid samples. Statistical analyses indicate that the discharge process of queuing vehicles can be divided into three distinct stages according to the discharge flow rate: a start‐up stage, a steady stage, and a rush stage. The average time for queuing vehicles to reach a stationary saturation flow rate, that is, the start‐up stage, was found to be approximately 20–30 seconds; the rush stage usually occurs during the phase transition period. The finding is contrary to the conventional assumption that the discharge rate reaches a maximum value after the fourth vehicle is discharged and then remains constant during the green time until the queue is completely dissolved. The capacity estimation errors that might arise from the conventional methods are discussed through a comparative study and a sensitivity analysis that are based on the identified queue discharge patterns. In addition, a piecewise linear regression method was proposed in order to reduce such errors. The proposed method can be used for capacity estimation at signalized intersections with the identified queue discharge patterns. Copyright © 2017 John Wiley & Sons, Ltd.     

Theoretical studies of active power/angle sub-matrix in power flow Jacobian for power system analysis

Properties of the active power/angle sub-matrix in the power flow Jacobian for power system analysis are studied. The sub-matrix is a dominant and irreducible matrix under very general conditions of power systems, so that it is invertible. Also the necessary conditions for its singularity are given. These theoretical results can be used to clarify the ambiguous understanding of the sub-matrix in current literature, and also provide the theoretical foundations for the applications based on reduced power flow Jacobian. Numerical simulation on the IEEE 118-bus power system is used to illustrate our results.     

Characterization of incidents on an urban arterial road

The early warning of incidents on urban arterial roads in a congested city can reduce delay, accidents and pollutant emission. Freeway incident detection systems implemented in recent years may not be suitable for arterial incidents. Arterial incident detection is more difficult. The traffic flow on an arterial road is not conserved from the upstream end of a road link to the downstream end because urban traffic does turn in and out of side‐streets, car‐parks and local residences. Roadside friction such as kerbside parking and shopping traffic also tends to create apparent incidents which are in fact frequent and normal events. This paper develops a definition for an arterial incident and describes a case study on an arterial road in Melbourne, Australia. The study shows that detectors upstream of an incident are more useful for incident detection than downstream detectors. It also identifies occupancy and speed as the appropriate parameters to characterise and detect arterial incidents.     

Cross-sector Analysis of Four Renegotiated Transport PPPs in Portugal

Abstract

This paper uses the Fertagus renegotiation results as a reference and explores the features that made it such a widely commended case, aiming to identify the best practice to be followed in other cases. The two main questions that this paper aimed to respond were: Was the success of the renegotiation process in the Fertagus contract due to mode-specific factors? Are those factors (mode specific or not) transferable to other modes under public private partnership (PPP) contracts and if so, to what extent? Regarding the mode specificity and transferability analysis, it can be noticed that much of the features were not mode specific in theory, however for the successful transferability to other transport modes, some changes should be made to the PPP model taking into account modal specificities and national contexts.     

欠驱动ODINs的全局逆最优循迹控制（英文）

This paper presents a design of optimal controllers with respect to a meaningful cost function to force an underactuated omni-directional intelligent navigator(ODIN) under unknown constant environmental loads to track a reference trajectory in two-dimensional space. Motivated by the vehicle’s steering practice, the yaw angle regarded as a virtual control plus the surge thrust force are used to force the position of the vehicle to globally track its reference trajectory. The control design is based on several recent results developed for inverse optimal control and stability analysis of nonlinear systems, a new design of bounded disturbance observers, and backstepping and Lyapunov’s direct methods. Both state- and output-feedback control designs are addressed. Simulations are included to illustrate the effectiveness of the proposed results.     

A multiobjective planning model for intercity train seat allocation

This paper presents a multiobjective planning model for generating optimal train seat allocation plans on an intercity rail line serving passengers with many‐to‐many origin‐destination pairs. Two planning objectives of the model are to maximise the operator's total passenger revenue and to minimise the passenger's total discomfort level. For a given set of travel demand, train capacity, and train stop‐schedules, the model is solved by fuzzy mathematical programming to generate a best‐compromise train seat allocation plan. The plan determines how many reserved and non‐reserved seats are to be allocated at each origin station for all subsequent destination stations on each train run operated within a specified operating period. An empirical study on the to‐be‐built Taiwan's high‐speed rail system is conducted to demonstrate the effectiveness of the model. The model can be used for any setting of travel demand and stop‐schedules with various train seating capacities.     

An ERP approach for container terminal operating systems

The major characteristics of ERP (Enterprise Resource Planning) are an enterprise-wide system that covers all the business functions and information resources, integrated database, built-in best industry practice, packaged software and open architecture. ERP enables reduction of system development time, flexibility, standardization of workflow and effective business planning capability. ERP is mainly for the manufacturing industry. However, the principles of ERP can also be applied to container terminal operating systems. This paper presents an ERP system approach for a container terminal. It has clustered the workflow of a container terminal and analysed the business process to generate the best workflows. The integrated database is designed to eliminate redundancy and keep integration. The core of ERP for container terminal is the planning facility such as berth planning and yard planning. The planning capability is very tightly coupled with data flow from client entities such as shipping companies. The ERP can handle the existing problems of container terminal operation that are mainly caused by lack of integration of a whole information resource in a container terminal, ad-hoc and poor planning capability, disconnected and incorrect data from client companies. The ERP approach can not only resolve the problems of container terminals but also promote adoption of information systems for container terminals in the world that have not yet implemented terminal operating systems.