汽车零部件集中采购决策矩阵

对汽车制造商集中采购和资源分配中出现的问题进行了分析,提出了以价格—索赔率矩阵进行优选供应商、集中采购的方法,解决了如何与供应商实现双赢问题。     

Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Hub location with flow economies of scale

A characteristic feature of hub and spoke networks is the bundling of flows on the interhub links. This agglomeration of flows leads to reduced travel costs across the interhub links. Current models of hub location do not adequately model the scale economies of flow that accrue due to the agglomeration of flows. This paper shows that current hub location models, by assuming flow-independent costs, not only miscalculate total network cost, but may also erroneously select optimal hub locations and allocations. The model presented in this paper more explicitly models the scale economies that are generated on the interhub links and in doing so provides a more reliable model representation of the reality of hub and spoke networks.     

对无锡市高职教育培养目标与模式的探讨

文章在借鉴国内外有关高职教育培养目标与模式的理论成果和实践经验的基础上,紧密结合无锡市的实际情况,对构建具有无锡地区特色的高职教育培养目标和模式进行了较为深入的探讨。     

钢板桩围堰的设计与施工

本文就某桥基础施工采用的钢板桩围堰,按照理论计算方法进行了钢板桩围堰设计,并通过施工对设计结果进行了验证。     

Parametric Hull Form Optimization of Containerships for Minimum Resistance in Calm Water and in Waves

This paper described the process of generating the optimal parametric hull shape with a fully parametric modeling method for three containerships of different s...     

禹登高速公路下伏采空区注浆治理工程质量检测技术

根据禹登高速公路采空区治理工程的实践,总结完善在复杂地质条件下,高等级公路下伏采空区注浆治理工程质量和效果检测评价的综合方法与技术,可供国内同类工程借鉴.     

Book review

Onshore Planning for Offshore Oil—Lessons from Scotland by Pamela L. Baldwin and Malcolm F. Baldwin The Conservation Foundation, Washington, D.C., 1975     

Methodology for the accuracy improvement of FEM beam type T-junctions of buses and coaches structures

The analysis of structures with finite elements methods (FEM) represents a widely spread technique. For large tubular structures similar to the buses and coaches upper structures, beam type elements are utilized due to the fact that these elements provide satisfactory results at relatively reduced computational performances. However the beam type elements have a main disadvantage determined by the fact that the modeled joints have an infinite rigid behavior. This shortcoming determines a stiffer behavior of the modeled structures which translates into an error source for the structural simulations (up to 45%). To overcome this problem, a simple methodology was conceived and an alternative optimized equivalent beam model obtained. The methodology studies the behavioral characteristics of beam modeled T-junctions determining their limitations and comparing them to equivalent T-junctions modeled with shell and volume elements. This way an improved Tjunction has been obtained, in which the behavioral error was reduced to less than 5%. Furthermore the FEM obtained results were validated with real T-junctions.