Stress sensitivity analysis and optimization of automobile body frame consisting of rectangular tubes

At conceptual design stage, beam element is extensively used to create the frame structure of automobile body, which can not only archive the accurate stiffness but also reduce much computational cost. However, the stress definition of beam element is very complex so that the stress sensitivity and optimization are difficult to analytically derive and numerically program. This paper presents an solution to this problem and an application in the lightweight optimization design of automobile frame. Firstly, maximal Von Mises stress of rectangular tube is calculated by using the superposition of stress, which is together induced by the axial force, bending moments, torsional moment and shear force. Secondly, the sensitivity of Von Mises Stress with respect to size design variables: breadth, height and thickness are derived, respectively. Thirdly, an optimal criterion is constructed by Lagrangian multiplier method to solve the frame optimization with stress constraints. Lastly, numerical example of car frame proves that the proposed method can guarantee the stress of each beam element almost fully reaches at the yielding stress.     

A Novel Image Encryption Technique Based on Inter Block Difference

Data security plays a vital role in the current scenario due to the advanced and sophisticated data access techniques.Present development in data access is alwa...     

Dynamic Performance of a Bulkhead Flat Car

The dynamic performance of a flat car is studied herein. The performance indices include roll angles, lateral accelerations, center plate loads, side bearing loads, wheel loads and spring deflections. These variables are maximum when the car is running at its critical speed, corresponding to either the rock and roll, or the bounce mode. The Association of American Railroads' (AAR) Flexible Carbody Model was used. The input for vertical track irregularities used in the simulation was generated from published spectra for U.S. Federal Railroad Administration (FRA) Class 4 track. After studying the car's performance with various column loads and spring suspensions, it was found that the most commonly used column load of 4,000 lbs. (17.8 kN) should be used. The spring suspension used in the original car design should also be adopted, in order to avoid spring bottoming.     

Computer-Simulation of the Dynamical Curving Behaviour of a Railway-Bogie

This paper describes the modelling of a two axle railway-bogie with variable design configurations and its application in the investigation of the behaviour in transitional and circular curves. Several results indicate possibilities to improve the curving properties and recommend the usage of forced-steering bogies, which show better performance in narrow curves without unbearable sacrifices to high-speed-behaviour on straight track.     

Development of an LIF image processing technique for measuring drop sizes in a pre-swirl spray

Depth of field effects in laser sheet imaging were considered for droplet sizing of a pre-swirl spray. A pre-swirl spray is formed before the hollow-cone type main-swirl spray from a D.I. gasoline injector, and shows transient characteristics with high axial velocity. A microscopic imaging technique was applied to obtain high spatial resolution LIF tomograms of the pre-swirl spray. A 1 mm thick Nd:YAG laser sheet was used as a light source to make the LIF tomograms that were imaged using a high-resolution CCD camera. The droplet sizing of the pre-swirl spray was carried out using an image processing technique. In the image processing procedure, the laser sheet-straddling large-sized droplets were carefully taken into account to remove the errors caused by the depth of field effects from the limited thickness and the energy distribution of the laser sheet. The mean intensity of the individual droplets and the line profile of the LIF signal around the droplet edge were inspected to screen the laser sheet-straddling large-sized droplets. In order to consider the effects of the size-dependent LIF signal intensity, the size-classified or ensemble-averaged mean intensity of the individual droplets was introduced. The mean droplet sizes such as AMD and SMD were calculated using only screened droplets, and they slightly increase before considering the depth of field effects.     

Links between subjective and objective evaluations regarding the steering character of automobiles

This work presents an experiment on the relationships between subjective and objective evaluations of vehicle handling. Ten cars were examined objectively in several open-loop driving dynamics manoeuvres and subjectively by test persons in typical traffic situations. Results are extracted from a stationary test (the Slowly Increasing Steer Test), and a dynamical test (the Frequency Response Test). The subjective measurements are obtained from drivers on a rural road course via a questionnaire, which was developed to separately investigate the quantity level perception, the so-called “Niveau”, and the more qualitative “Liking”. These subjective “measurements” are embedded into a two-channel definition of “Steering Comfort” as a genus for “Steering Discomfort” and “Character”. The article concentrates on developing a statistical method for the consideration of correlations amongst the subjective/objective data. In doing so, the variance in example subjective Niveau ratings can be significantly explained by several objective quantities. Indicators for co-domains of validated discomfort characteristics and hints for endeavouring character Liking ranges are detected.     

Vehicle interior noise model based on a power law

Identifying the components of a vehicle’s interior noise is important in many phases of the noise, vibration, and harshness (NVH) development process. Many test methods that have been widely used in the automobile industry to separate noise sources are based on system identification methods in the frequency domain. However, none of the frequency response function-based methods can directly estimate the wind noise component. In this article, an analytical model for the interior noise level based on a simple power law was developed. It was assumed that the mean squared acoustic pressure for the interior noise could be obtained by summing up those of the wind noise, road noise, and background noise. The wind noise and road noise were further assumed to depend only on wind speed and the vehicle’s driving speed, respectively, and to follow a simple power law. The resulting analytical model includes five parameters that can be optimized for the vehicle and the road. The validity of the model was verified by using data obtained from cruise tests performed on a proving ground for cruise speeds ranging from 40 km/h to 130 km/h. The model is applied to the overall and 1/3-octave bands of interior noise and is shown to describe the data trends fairly well. For the test vehicle used in the present work, the overall mean squared pressures for the wind and road noise components are shown to be proportional to the wind speed to the 5.8 power and to the driving speed to the 3.4 power, respectively.     

Observations on colony formation by the cosmopolitan phytoplankton genus Phaeocystis

Few marine phytoplankton have heteromorphic life cycles and also often dominate the ecosystems in which they occur. The class Prymnesiophyceae contains a notable exception: the genus Phaeocystis includes three species that form gelatinous colonies but also occur within their ranges as solitary cells. Phaeocystis antarctica and P. pouchetii are exclusively high latitude taxa, and are notable for regionally tremendous blooms of the colony stage. P. globosa occurs circumglobally, yet its colony blooms primarily are confined to colder waters within its range. Three additional species are warm water forms that have been reported only as solitary cells or loose aggregations that bear little resemblance to the organized colonies of the other taxa. Interpretation of existing data indicates that resource availability (light, temperature and nutrients) by itself is not sufficient to explain this distinction between cold-water colony-forming taxa and warm water solitary cell taxa, nor why colony development in P. globosa is essentially a spatially restricted phenomenon within a much broader geographic range. Colony development by P. globosa in situ has been observed at temperatures ≥20 °C, but only rarely and generally under conditions of seasonally or anthropogenically elevated nutrient supply. Data presented here demonstrate colony development at 20–22 °C in natural plankton communities from oligotrophic waters that were pre-screened through 63 μm mesh (i.e. lacking mesozooplankton and large microzooplankton), but not in unscreened communities containing microzooplankton and >63 μm zooplankton. Reduction of colony proliferation at higher temperatures by mesozooplankton grazing remains as an intriguing possibility that is consistent with available evidence to help explain differences in latitudinal extent of in situ colony development. These data are interpreted within a theoretical framework regarding the potential advantages and disadvantages of the two life cycle stages.