Cycle-simulation turbulence modelling of IC engines

Numerical simulations of IC engines are of high interest for automotive engineers worldwide. The simulation models should be as fast as possible, low-computational effort and predictive tool. The correct prediction of turbulence level inside the combustion chamber of spark ignition engines is the most important factor influencing to the engine working cycle. This paper presents a development of the k-ε turbulence model applied to the commercial cycle-simulation software with the high emphasis on the intake part. The validation was performed on two engine geometries with the variation of engine speed and load comparing the cycle-simulation results of the turbulent kinetic energy and in-cylinder temperature with 3-D CFD results. In order to apply the cycle-simulation turbulence model for the simulation of entire engine map, the parameterization model of turbulence constants was proposed. The parameterized turbulence model was optimized using NLPQL optimization algorithm where the single set of turbulence model parameters for each engine was found. A good agreement of the turbulent kinetic energy during the expansion was achieved when the turbulence affects the flame front propagation and combustion rate as well.     

The EEZ and the progress of fisheries negotiations January to May 1977

This paper discusses negotiations, relative to sea fisheries, in terms of international arrangements—arrangements between the European Economic Community (EEC) and Third Countries; and those between member states of the EEC.     

Effective method for knock signal denoising in internal combustion engine

Uncontrolled expansion of combustion wave in spark ignited internal combustion engine causes knock effect which seriously degrades efficiency and lifetime of the engine. Thus, accurate knock detection and control are essential for obtaining a desired performance from the engine. Usually, knock sensor is used to detect this phenomenon but it has limited accuracy especially at engine high-speed rotations because of natural vibration and external noises. In this study an effective method based on Non-Local Mean (NLM) algorithm has been proposed to improve the knock detection accuracy. This method is evaluated based on four different indicators and four engine cylinders. The results show 52.9 % improvement in knock detection. Also feasibility of real time execution of this method based on embedded hardware has been studied.     

Estimation of the effects of aircraft noise on residential satisfaction

This study assesses the effects of aircraft noise on residential satisfaction, an important indicator of subjective well-being. A structural equation model is specified that estimates the relationships between objective variables, noise annoyance variables and residential satisfaction. Secondary data-analysis is used to estimate the model. The survey was conducted in 1996/1997 among the population living within a 25-km radius of Amsterdam Schiphol, the largest airport in the Netherlands. The effect of aircraft noise annoyance is found to be relatively small. In addition, the objective level of aircraft noise exposure is found to be a better predictor of residential satisfaction than its subjective counterpart. The most important determinants of residential satisfaction are found to be road traffic noise annoyance, age and neighbor noise annoyance.     

Wave propagation in head on bonnet impact: Material and design issues

Head on bonnet impact is becoming more and more important in automotive design as regulations on pedestrian safety become more demanding. Despite the relatively low amount of energy involved, these impacts are truly dynamic phenomena as the event duration is comparable with the traveling time of the different wavefronts generated by the impact. In this paper, we show that we can build up a simplified model for the impact based on wave propagation analysis. Using this model, we can analyze head acceleration on existing bonnets or predict it on new ones. Head acceleration in a bonnet impact can thus be estimated over the whole area of the bonnet with a few minutes of CPU.     

Review of flywheel based internal combustion engine hybrid vehicles

Hybrid vehicles of different configurations and utilizing different energy storage systems have existed in development for many decades and more recently in limited production. They can be grouped as parallel, series or complex hybrids. Another classification is micro, mild and full hybrids which makes the distinction on the basis of functionality. The common energy storage systems in hybrid vehicles are batteries, supercapacitors and high speed flywheels. This paper aims to review a specific type of hybrid vehicle which involves the internal combustion engine (ICE) as the prime mover and the high speed flywheel as an energy storage device. Such hybrids are now attracting considerable interest given their potential for low cost. It is hence timely to produce a review of research and development in this subject. The flywheel is coupled to the drive line with a continuous variable transmission (CVT). The CVT can be of various types such as electrical, hydraulic or mechanical but usually in this case it is a non-electrical one. Different configurations are possible and the paper provides a timeline of the development of such powertrains with various examples. These types of hybrid vehicles have existed as prototypes for many decades and the authors believe that their development has reached levels where they can be considered serious contenders for production vehicles.     

Finite element modeling of static tire enveloping characteristics

To investigate static tire enveloping characteristics, a three dimensional (3-D) finite element model is proposed. The vertical stiffness of the tire is studied on a flat surface with and without cleat. Tire rubber materials and cord layers are represented independently using “rebar” elements available in MSC Marc Mentat. Comparisons of numerical and experimental results are given to show the validity of the proposed model. It is shown that after a certain displacement, the results of the proposed model agree well with experimental results. In addition, the model results show that regardless of the type of the cleat placed under the rim center (hub center), all vertical force curves intersect after a certain displacement, which indicates typical static enveloping characteristics. Moreover, another typical characteristic of the radial tires that is unlike those of bias-ply constructions confirms that the contact patch does not expand laterally after a level vertical load is applied to the tire, which is directly related to fuel consumption and tire tread life.