Light rail transit in Canada

This paper describes current light rail transit planning and operation in Canada's major cities and smaller communities. There are ten urban areas in Canada with 250,000 or more people. Two of these have light rail systems in operation, three have lines under construction and nine others are planning LRT systems.     

西藏复杂地质环境下路基加宽拼接方案试验研究

针对西藏某公路的加宽改造,提出了5种新旧路基加宽拼接方案.按这5种方案,共修筑了3段试验路.对试验路的设计原则、施工要求和工艺进行了讨论.通过试验数据,对各种拼接方案的效果进行了比较分析.结果表明,用5层双向土工格栅自路基顶面向下,以层间距30 cm的加筋方式加强新旧路基间的结合是较好的路基加宽拼接方案.     

Les systèmes de vélos en libre-service expliquent-ils le retour du vélo en ville ?

Many French and European cities have developed a bike sharing system since 2005. This policy may be explained in a great part by the success of the Velo??v in Lyon, which contributed to improve the image of cycling in the city. If bicycles, however, appear to find a new place in the city, one can wonder whether this is really due to bike sharing systems? What are the real uses of bicycles in contemporary cities, with or without such a system? To answer these questions, the paper starts with a literature review on bicycle in the city, to draw lessons from recent experiences of bike sharing systems. It then discusses the two cases of Lyon and Lille, which never had a bike sharing system on its own. The evolution of bicycle use is measured with a comparison of household transportation surveys in Lyon (1995 and 1998) and Lille (1998 and 2006). In both cities, the analysis reveals a rise in the proportion of healthiest citizens among urban bikers, as well as a return of bikes in dense areas. Bike sharing systems are part of such tendencies. They support them, but should not become a panacea for policies supporting bike use in the city.     

Comparative analysis of vehicle brake data in the ministry of transport test on the roller brake tester and on flat ground

This study performs a comparison between what occurs when braking on a Ministry of Transport (MOT) brake tester and on flat ground. The tire pressure is changed, but the other parameters remain constant. The results from this research and from the in-depth comparative study conducted by the mechanical engineering staff in the mechanical laboratory at the Miguel Hernández University in Elche have led to the following main conclusions: By varying the tire pressure, false results can be obtained with the MOT brake tester, which means that, if the tires are inflated at a low pressure but the brakes are in good condition, the vehicle will not pass the MOT. Conversely, if the brakes are in poor condition but the tire pressure is higher than what is recommended by the manufacturer, a false pass is produced. This article shows that the MOT brake testing equipment is often wrong and inexact, and the data and graphs presented prove that the tire pressure is a determining factor when assessing the condition of brakes.     

Aerodynamic design optimization of rear body shapes of a sedan for drag reduction

This study proposes an aerodynamically optimized outer shape of a sedan by using an Artificial Neural Network (ANN), which focused on modifying the rear body shapes of the sedan. To determine the optimization variables, the unsteady flow field around the sedan driving at very fast speeds was analyzed by CFD simulation, and fluctuations of the drag coefficient (C _D ) and pressure around the car were calculated. After consideration of the baseline result of CFD, 6 local parts from the end of the sedan were chosen as the design variables for optimization. Moreover, an ANN approximation model was established with 64 experimental points generated by the D-optimal methodology. As a result, an aerodynamically optimized shape for the rear end of the sedan in which the aerodynamic performance is improved by about 5.64% when compared to the baseline vehicle is proposed. Finally, it is expected that within the accepted range of shape modifications for a rear body, the aerodynamic performance of a sedan can be enhanced so that the fuel efficiency of the sedan can be improved. The YF SONATA, a sedan manufactured by Hyundai Motors Corporate, played a major role in this research as the baseline vehicle.     

Study of an optimized gas strut layout to improve opening and closing quality

The most important factor in gas strut design is determining an optimized layout. If the layout is not optimized, vehicle operators will have a suboptimal experience when opening and closing the tailgate. A poor layout of the gas struts causes operators to work excessively when they open/close the tailgate, and vehicle owners will incur additional expenses due to deterioration in the body quality of the vehicle. Thus, an optimized gas strut layout is very important, even if it does not seem interesting. This paper describes the tailgate operation process and focuses on determining an optimized gas strut layout for opening/closing the tailgate easily.     

High-strain-rate fracture of adhesively bonded composite joints in DCB and TDCB specimens

Double-cantilever beam (DCB) and tapered double-cantilever beam (TDCB) specimens are the test configurations most commonly used to measure the fracture toughness of composites and adhesive joints. Strain rates of 1 to 18.47 m/s were applied to the test specimens via high-speed hydraulic test equipment. Because the fracture occurs through the adhesively bonded joints and the cracks grow rapidly, the crack length and beam displacement were recorded by a high-speed camera. An energy range from 0 to 10 J was often observed in the high-strain-rate fracture experiments for nonlinear plastic behavior of the dynamically loaded adhesively bonded DCB and TDCB specimens. The range of energy release rates (fracture energy) for TDCB specimen was 2 to 3 times higher than that of a DCB specimen for all high strain rates. The fracture energy of automotive adhesive joints can be estimated using the experimental results in this study for the fracture toughness (G_IC) under high rates of loading. The crack grows as the applied fracture energy exceeds the value of the critical energy release rate (G_IC) at the crack tip. The energy release rate was calculated using the fracture mechanics formula. The key fracture mechanics parameter, the fracture energy GIC, was ascertained as a function of the test rate and can be used to assess and model the overall joint performance.     

Evasive manoeuvres with a steering robot

In the pursuit of an objective rating on vehicle stability performance, it is always desirable to reduce disturbances and inconsistencies during experimental evaluations, especially the ones introduced by human drivers. This paper presents the development of a steering robot designed for closed-loop steering tasks during evasive manoeuvres. It describes the controller structure and discusses experimental results, in addition to simulation/vehicle model verifications and theoretical control analysis.     

Insights into vehicle trajectories at the handling limits: analysing open data from race car drivers

Race car drivers can offer insights into vehicle control during extreme manoeuvres; however, little data from race teams is publicly available for analysis. The Revs Program at Stanford has built a collection of vehicle dynamics data acquired from vintage race cars during live racing events with the intent of making this database publicly available for future analysis. This paper discusses the data acquisition, post-processing, and storage methods used to generate the database. An analysis of available data quantifies the repeatability of professional race car driver performance by examining the statistical dispersion of their driven paths. Certain map features, such as sections with high path curvature, consistently corresponded to local minima in path dispersion, quantifying the qualitative concept that drivers anchor their racing lines at specific locations around the track. A case study explores how two professional drivers employ distinct driving styles to achieve similar lap times, supporting the idea that driving at the limits allows a family of solutions in terms of paths and speed that can be adapted based on specific spatial, temporal, or other constraints and objectives.     

Experimental investigation using CFD for thermal performance of ventilated disc brake rotor

In the present work, different ventilated disc brake rotor configurations were analysed to enhance the heat transfer rate and obtain the uniform temperature distribution in the rotor. CFD code used in this work was validated at using experimental results obtained by conducting experiments on a test rig. The experimental analysis was performed to calculate the mass flow rate and heat dissipation through the rotor. Further, different types of rotor configurations viz. straight radial vane (SRV), tapered radial vane (TRV), alternate long and short vane (ALSV), variable diameter circular pillars (VDCP) were considered for the analysis. A rotor segment of 20° was considered for the numerical analysis due to its rotational symmetry. CFD results were in good agreement with the experiments. The maximum deviation of the numerical results were about 12 % from the experimental results. It is found from the analysis that among the different types of rotor configurations; variable diameter circular pillars (VDCP) rotor gives better rate of heat dissipation with more uniform temperature distribution in the flow passages. Hence for modern high speed vehicles VDCP rotor may be more appropriate.