Deflection test and transmission error measurement to identify hypoid gear whine noise

T-Hypoid gears are commonly used in rear-drive and 4WD (4 Wheel Drive) vehicle axles. Investigating their sensitivity to deflections is one of the most important aspects of their design and optimization procedures. Therefore, a deflection test was performed in this study in the actual gear mounting using completely processed gear. This test covered the full operating range of gear loads from “no load” to “peak load”. Under peak load, the contact pattern extended to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface. The transmission error was tested under an axle assembly triaxial-real-car-load condition.     

Off-set crack propagation analysis under mixed mode loadings

An assessment was carried out herein to study the eccentricity of cracks subjected to mixed-mode loadings. Several loading locations relative to a central line were selected to induce mixed-mode loadings, which were computed using a finite element method. An adaptive meshing technique was adopted during the simulation of crack propagation to ensure the singularity of stress at the tip of the crack. The stress intensity failure criterion was used and programmed, and the node splitting technique was used when the stress intensity factor reached the fracture toughness of the material to simulate crack propagations. It was found that large variations in the stress intensity factor were observed when off-set cracks were used, and that K _II decreased when loading distance increased, but increased when the off-set crack distance was increased. Both crack eccentricity and loading distance played important roles in producing mixed-mode loading, compared to the influence of central cracks. Correction factors were introduced to modify the calculation of stress intensity factors under mixed-mode loadings. Simulations of crack propagation were also conducted to study the effects of crack eccentricities and loading distances. It was found that the crack length, the loading distance relative to the central crack and the crack eccentricity dominated calculations of the integrity of cracked structures.     

Haptic steering support for driving near the vehicle’s handling limits; skid-pad case

Current vehicle dynamic control systems from simple yaw control to high-end active steering support systems are designed to primarily actuate on the vehicle itself, rather than stimulate the driver to adapt his/her inputs for better vehicle control. The driver though dictates the vehicle’s motion, and centralizing him/her in the control loop is hypothesized to promote safety and driving pleasure. Exploring the above statement, the goal of this study is to develop and evaluate a haptic steering support when driving near the vehicle’s handling limits (Haptic Support Near the Limits; HSNL). The support aims to promote the driver’s perception of the vehicle’s behaviour and handling capacity (the vehicle’s internal model) by providing haptic (torque) cues on the steering wheel. The HSNL has been evaluated in (a) driving simulator tests and (b) tests with a vehicle (Opel Astra G/B) equipped with a variable steering feedback torque system. Drivers attempted to achieve maximum velocity while trying to retain control in a circular skid-pad. In the simulator (a) 25 subjects drove a vehicle model parameterised as the Astra on a dry skid-pad while in (b) 17 subjects drove the real Astra on a wet skid-pad. Both the driving simulator and the real vehicle tests led to the conclusion that the HSNL assisted subjects to drive closer to the designated path while achieving effectively the same speed. With the HSNL the drivers operated the tires in smaller slip angles and hence avoided saturation of the front wheels’ lateral forces and excessive understeer. Finally, the HSNL reduced their mental and physical demand.     

Methodology for bus structure torsion stiffness and natural vibration frequency prediction based on a dimensional analysis approach

Engineering bus design requires testing of bus structures prototypes in order to guarantee a certain level of strength and an appropriate static and dynamic behavior of the bus superstructure when exposed to road loads. However, experimental testing of real bus structures is very expensive as it requires expensive resources and space. If testing is done on a scale bus model the previous required expenses are considerably reduced. Therefore, a novel methodology based on dimensional analysis applied to bus structure prediction to evaluate the bus structure static and dynamic performance is proposed. The static performance is evaluated attending to torsion stiffness and the dynamic in terms of the natural vibration frequencies and rollover threshold. A scale bus has been manufactured and dimensionless parameters have been defined in order to project the results obtained in the scale bus model to a larger model. Validation of the proposed methodology has been carried out under experimental and finite element analysis.     

Impact technique for measuring global dynamic stiffness of engine mounts

Engine mounts are used for engine vibration isolation. The dynamic performance of the mount depends on the orientation. Measurements of the dynamic properties of engine mounts are usually performed in the axial direction because of the problem related to actuator loading direction and set up costs. Impact technique is developed here to measure the dynamic driving point stiffness and driving point shear stiffness of engine mount in a single setup. The compressive and shear frequency-dependent stiffnesses are obtained in the vertical orientation. A transformation matrix is used to calculate the frequency-dependent stiffnesses and loss factors in other orientations. Three different designs of engine mounts are used to verify the accuracy of the transformation model. The correlation coefficient between calculation and measurement results show R²≥ 0.995 along the X- and Y-axes. For the Z-axis, mounts B and C showed R²≥ 0.95 and mount A 0.687 ≤ R²≤ 0.791.     

柴油机故障诊断专家系统知识库设计

在分析柴油机故障诊断知识特点的基础上,采用模糊化方法对柴油机运行状态参数进行处理,采用综合型知识方式来表达柴油机故障诊断知识,采用多库多层次的方式组织知识库,并对知识库采取一系列方式进行管理与维护。应用表明,柴油机故障诊断专家系统的预报准确率较高,具有较强的实用性。     

Spatial fisheries ecology: Recent progress and future prospects

We review recent progresses made in the study of fish distribution and survival over space — i.e., fisheries spatial ecology. This is achieved by first surveying the most common statistical approaches and relative challenges associated with the analysis of fisheries spatial data, loosely grouped in geostatistical and regression approaches. Then we review a selected number of case-studies implementing the discussed techniques. We conclude by proposing new areas of statistical and ecological research to further our understanding of how fish distribute and survive in space. This review serves a dual purpose by emphasizing the scientific importance of studying spatial interactions to better understand the temporal dynamics of fish abundance, and by promoting the development of new analytical and ecological approaches for the analysis of spatial data. Through our survey we cover different statistical techniques, marine ecosystems and life stages. This analytical, geographic and ontogenetic variety is also purposely selected to highlight the importance of comparative and multidisciplinary studies across diverging ecological disciplines, ecosystems and life stages. Besides having a general ecological relevance this review also bears a more applied significance, owing to the increasing need for protecting renewable marine resources along with their primary habitat.     

6502站继电器采集故障原因分析

本文通过对6502站继电器采集故障原因进行分析，提出用增加复示继电器、缩短电缆长度或采集电缆单独敷设的方法，减少采集故障发生，确保列控中心识别进路信息采集的正确性。     

Net tax incidence for urban public transit subsidies in New Zealand

This paper examines the impact of policy changes in the funding of New Zealand public transit modes.These changes, introduced in 1983, are evaluated in terms of the net incidence of public transit subsidy assistance, taking into account its source of funding and the income class of those commuters benefiting from the subsidy. The general conclusion is that the net incidence of subsidy assistance remains progressive (i.e., a transfer from high to low income commuters) following the introduction of shared funding on the predominant public transit modes (rail and bus), sourced from income tax (central government) and property tax (regional/local government). However, because of the predominance of medium to high income commuters on rail vis-a-vis bus and the traditional source of funding on these modes in terms of income tax (a progressive tax source) and property tax (a regressive tax source), the degree of progressivity previously associated with public transit subsidies has now substantially reduced.The analysis and opinions expressed in this paper are the responsibility of the author alone and do not purport to represent the views of the Ministry of Transport.     

Interval estimation in the calibration of certain trip distribution models

This paper argues for interval, rather than point, estimation when calibrating some variants of the trip distribution “gravity” models. Analytic expressions are derived for the approximate asymptotic covariances of least squares and maximum likelihood estimates of the parameters in the impedance function under a variety of conditions. A comparative numerical example, and an application using migration flows, are also presented.