Overturning Stability of Three Wheeled Motorized Vehicles

Three wheeled motorized vehicles are a major mode of public transport in many countries. These vehicles are prone to overturning even during normal turning and obstacle avoidance maneuvers. This paper presents a parametric analysis of a mathematical model of the vehicle and evolves guidelines for improving the overturning stability in terms of vehicle geometry and suspension properties.

Differential equations governing the dynamic behavior of the vehicle are derived on the basis of a six degree of freedom model. The vehicle response to variations in steering, engine power and braking inputs is then numerically simulated. The effects of vehicle geometry and elasto-damping suspension coefficients on the vehicle stability are presented. The results indicate an optimum position of the center of gravity where the vehicle is most stable. While stiffer suspensions favour stability, there exists an optimum value of suspension damping for which the minimum wheel load is a maximum.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Fatigue design for plug/ring type gas welded joints of sts301l including welding residual stresses

This paper presents a fatigue design method for plug and ring type gas welded joints, which incorporates welding residual stress effects. A non-linear finite element analysis (FEA) was first performed to simulate the gas welding process. The numerically predicted residual stresses of the gas welds were then compared to experimental results measured using a hole drilling method. In order to evaluate the fatigue strength of the plug and ring type gas welded joints, a stress amplitude (σ _a ) _R taling the welding residual stress of the gas weld into account was introduced and is based on a modified Goodman equation incorporating the effect of the residual stress. Using the stress amplitude (σ _a ) _R , the ΔP-N _f relations obtained from fatigue tests for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged into (σ _a ) _R -N _f relations. It was found that the proposed stress amplitude (σ _a ) _R could provide a systematic and reasonable fatigue design criterion for the plug and ring type gas welded joints.     

Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.     

Transient characteristics of emissions during engine start/stop operation employing a conventional gasoline engine for HEV application

In this paper, we investigate the transient characteristics of combustion and emissions during engine start/stop operations in hybrid electric vehicle (HEV) applications. Hydrocarbon (HC) emissions during the initial 2^nd∼9^th cycles are found to be significantly greater when the engine is quickly started under the original engine calibration mode. Lower intake manifold absolute pressure (MAP) was also found to cause larger residual gas dilution and poor combustion, resulting in a higher HC concentration when the cranking speed was increased. The post-catalyst HC concentration was found in the way of initially decrease and then to increase again as the cranking speed was increased. A lowest concentration value was achieved at a cranking speed of 1000 r/min. Engine shut-down by fuel cut-off was shown to produce lower emissions than shut-down by ignition cut-off as one can avoid misfire of the last fuel injection cycle. The fuel deposited during the stop process seems to impact engine restart enrichment mostly during the initial 0.7 s for this engine, whose performance is dominated by the MAP transition characteristic and the time coefficient for fuel vaporization in this time period     

Automotive structure vibration with component mode synthesis on a multi-level

The recursive component mode synthesis method (RCMS) has been implemented for the finite element analysis model of an automobile structure as an efficient free vibration analysis tool. The RCMS method is intended to obtain a better performance relative to the block Lanczos method, which is a traditional method in the industry of obtaining eigenvalues, while obtaining the acceptable accuracy. A numerical example of the automobile finite element model demonstrates the outstanding performance of RCMS compared to the block Lanczos method.     

不同稳定剂对SBS改性沥青稳定效果的对比研究

通过试验测试不同老化时间样品的针入度、软化点和延度比较其相容性和路用流变学性能指标的变化,分析体系宏观稳定性和稳定剂性能特征,并通过形态结构照片分析稳定剂改善的效果。结果表明,加入稳定剂后改性沥青的高温储存稳定性明显改善,同时加入FD-06无硫稳定剂的改性沥青在热储存过程中性能更加稳定,不易离析。沥青中的部分组份具有化学活性,利用其活性点,引入带有活性基团的反应物,并通过被引入分子的化学结构的调节改善SBS与沥青的相容性,从而制备储存稳定性良好的SBS改性沥青。化学改性技术的应用提高了路用改性沥青的性能/价格比。     

A fundamental investigation of tilt control systems for narrow commuter vehicles

One way of addressing traffic congestion is by efficiently utilizing the existing highway infrastructure. Narrow tilting vehicles that need a reduced width lane can be part of the solution if they can be designed to be safe, stable, and easy to operate. In this paper, a control system that stabilizes the tilt mode of such a vehicle without affecting the handling of the vehicle is proposed. This control system is a combination of two different types of control schemes known as steering tilt control (STC) and direct tilt control (DTC) systems. First, different existing variations of both STC and DTC systems are considered and their shortcomings analysed. Modified control schemes are then suggested to overcome the deficiencies. Then a new method of integrating these two control schemes that guarantees smooth switchover between the controllers as a function of vehicle velocity is proposed. The performance of the proposed STC, DTC, and integrated systems is evaluated by carrying out simulations for different operating conditions and some experimental work. The design of a second-generation narrow tilting vehicle on which the developed control system has been implemented is presented.     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.