Vehicle velocity estimation using effective inertia for an in-wheel electric vehicle

In this study, a vehicle velocity estimation algorithm for an in-wheel electric vehicle is proposed. This algorithm estimates the vehicle velocity using the concept of effective inertia, which is based on the motor torque, the angular velocity of each wheel and vehicle acceleration. Effective inertia is a virtual mass that changes according to the state of a vehicle, such as acceleration, deceleration, turning or driving on a low friction road. The performance of the proposed vehicle velocity estimation algorithm was verified in various conditions that included straight driving, circle driving and low friction road driving using the in-wheel electric vehicle that was equipped with an in-wheel system in each of its rear wheels.     

Fatigue strength assessment including welding residual stress of spot welded joints subjected to cross-tension loads

This paper presents a method to assess of fatigue strength for resistance spot welded joints, which incorporates welding residual stress effects. To achieve this, first, a non-linear finite element analysis (FEA) was performed to simulate the spot-welding process. To validate the FEA results, the numerically calculated welding residual stresses of spot welds were then compared with experimental results measured by X-ray diffraction method. The residual stress distributions showed good agreement between calculations and experiments. To evaluate the effects of welding residual stress on the fatigue design criterion of resistance spot welded joints subjected to cross-tension load, the stress amplitude (σ_a-res) taking into account welding residual stress at a spot weld was proposed based on a modified Goodman equation incorporating the residual stress effect. Using the stress amplitude σ_a-res at the nugget edge of a spot weld, the ΔP ? N_f relations obtained as the fatigue test results for spot welded joints were systematically rearranged to the σ_a-res ? N_f relation. It was found that the proposed stress amplitude (σ_a-res) provides more reasonable and accurate fatigue design criterion of spot welded joints subjected to cross-tension load.     

Evaluation and visualization of stratified ultra-lean combustion characteristics in a spray-guided type gasoline direct-injection engine

To comply with reinforced emission regulations for harmful exhaust gases, including carbon dioxide (CO₂) emitted as a greenhouse gas, improved technologies for reducing CO₂ and fuel consumption are being developed. Stable lean combustion, which has the advantage of improved fuel economy and reduced emission levels, can be achieved using a sprayguided-type direct-injection (DI) combustion system. The system comprises a centrally mounted injector and closely positioned spark plugs, which ensure the combustion reliability of a stratified mixture under ultra-lean conditions. The aim of this study is to investigate the combustion and emission characteristics of a lean-burn gasoline DI engine. At an excess air ratio of 4.0, approximately 23% improvement in fuel economy was achieved through optimal event timing, which was delayed for injection and advanced for ignition, compared to that under stoichiometric conditions, while NO_x and HC emissions increased. The combustion characteristics of a stratified mixture in a spray-guided-type DI system were similar to those in DI diesel engines, resulting in smoke generation and difficulty in three-way catalystutilization. Although a different operating strategy might decrease fuel consumption, it will not be helpful in reducing NO_x and smoke emissions; therefore, alternatives should be pursued to achieve compliance with emission regulations.     

Preview suspension control for a full tracked vehicle

In this study, preview control algorithms for the active and semi-active suspension systems of a full tracked vehicle (FTV) are designed based on a 3-D.O.F model and evaluated. The main issue of this study is to make the ride comfort characteristics of a fast moving tracked vehicle better to keep an operator’s driving capability. Since road wheels almost trace the profiles of the road surface as long as the track doesn’t depart from the ground, the preview information can be obtained by measuring only the absolute position or velocity of the first road wheel. Simulation results show that the performance of the sky-hook suspension system almost follows that of full state feedback suspension system and the on-off semi-active system carries out remarkable performance with the combination of 12 on-off semi-active suspension units. The results simulated with 1^st and 2^nd weighting sets mean that the suspension system combined with the soft type of inner suspension and hard type of outer suspension can carry out better ride comfort characteristics than that with identical suspensions. The full tracked vehicle (FTV) system is uncontrollable and the system is split into controllable and uncontrollable subspace using singular value decomposition transformation. Frequency response curves to four types of inputs, such as heaving, pitching, rolling, and warping inputs, also demonstrate the merits of preview control in ride comfort. All the frequency characteristic responses confirm the continuous time results.     

Simulation of flow in diesel particulate filter system using metal fiber filter media

Metal fiber is introduced as a new filter media in wall-flow Diesel Particulate Filter (DPF) system. This technology has high temperature durability which is required for filter regeneration, and can maintain the mechanical strength even in the extreme exhaust-related vibrations of vehicles. However, the regeneration near the wall (outer layer) is more difficult because of the heat loss and reduced gas flow near the wall. In this study, a flow is simulated to determine the flow control method for the more uniform flow in all filter layer. By using Star CCM+ commercial software, we obtain local velocity, streamline, and pressure distributions in the filter, which are typically difficult to obtain from measurements. The major control factors are the filter porosity, size and location of the distribution plate, and the number of blades of the swirler. By placing the distribution plate in front of the filter, the flow velocity near the wall was increased. The optimum location and size of the flat plate were chosen. By attaching the blade on the plate the flow velocity near the wall was increased more. Therefore, the regeneration efficiency is increased by using the swirler-type metal fiber DPF system.     

Realization of pmp-based control for hybrid electric vehicles in a backward-looking simulation

Optimal control is generally not possible without information about the future coming up, and it is not easy to obtain an optimal solution even though the information is given a priori. In this paper, a control concept based on Pontryagin’s Minimum Principle (PMP) is introduced as an efficient solution to generate an optimal control trajectory for Hybrid Electric Vehicles (HVEs) when the performance of the vehicles is evaluated on scheduled driving cycles at a simulation level. The main idea of the control concept is to minimize Hamiltonian, which is interpreted as equivalent fuel consumption, and the Hamiltonian is characterized by a co-state, which is interpreted as a weighting factor for the electrical usage. A key aspect of the control problem is that an appropriate initial condition of the co-state is required to satisfy the boundary condition of the problem. In this study, techniques to calculate the Hamiltonian in different hybrid configurations are introduced, and a methodology to look for the initial condition of the co-state is studied, so that the controller is able to realize a desired State Of Charge (SOC) trajectory. To address the issue, we utilize a shooting method with multiple initial conditions based on the concept of the Newton-Raphson method, and all these techniques are realized in a backward looking simulator. The simulation results show that the PMP-based control is a very efficient approach to produce the optimal control trajectory, and the performance is compared to the optimal solution solved by Dynamic Programming (DP).     

Durability prediction for automobile aluminum front subframe using nonlinear models in virtual test simulations

This research work presents fatigue life evaluation techniques for an automotive vehicle aluminum front subframe using virtual test simulation technology with nonlinear suspension components model. The technology was used for improving the accuracy of the polynomial model used in conventional analysis. The proposed nonlinear suspension components models were developed using direct approach. The effects of the nonlinear elements on the prediction of the fatigue life were also analyzed. Actual aluminum front subframe was tested using half-car road test simulator to verify the accuracy of the models. It was found that the proposed nonlinear models yield more accurate results than conventional polynomial models. The proposed virtual test simulation technology with nonlinear suspension components model can be used to predict fatigue life for vehicle chassis structures more accurately.     

Improvement of long-term lives of rubber gaskets of polyacrylate (ACM) by employing carboxyl cure sites

Rubber gaskets are used widely in many industries. An evaluation of the material properties and an accurate lifetime prediction of rubber are very important in the design process to ensure the durability and reliability of rubber components. The properties of rubber-like materials are sensitive to ambient conditions, such as temperature, environment and mechanical load. Moreover, the initial properties of rubber gaskets must be sustained under working conditions to maintain its sealing function. To perform tests within a reasonable time, the highly accelerated life test (HALT) is generally used to predict the long-term lifetime of rubber materials. Polyacrylate (ACM) with chlorine cure sites is generally used for engine head gaskets. An ACM with carboxyl cure sites was developed to improve the lifetime of the gaskets. A four-parameter method representing the recovery behavior of the gaskets was published recently, and two revised methods for obtaining the recovery were proposed. The mean squared errors (MSEs) of the regression methods and experimental data were compared. The life of a gasket for the target recovery (60%) of a compressed gasket was calculated somewhat differently depending on the selected regression model to predict a considerably different long-term life. The parameters in the regression models were obtained using the successive zooming genetic algorithm (SZGA), and the lives of ACM with a carboxyl cure site and ACM with a chlorine cure site were compared.     

Regularity analysis on transient over-voltage of grounding grid by lighting strokes in substationsEI北大核心

Research purposes: Lightning has been one of the important factors endangering safe and reliable operation of the railway. The grounding grid performance plays a particularly important role in lightning protection. In this paper, the author has established a grounding grid transient model by the electromagnetic transient analysis software and intended for quantitative analysis of typically grounding grid layout in engineering practice, to lay important theoretical basis for future lightning protection and grounding. Research conclusions: (1) The results show that the ground potential is significantly affected by the soil resistivity, lightning current amplitude and the mesh size. With increase of the soil resistivity and lightning current amplitude, the ground potential at the point of the lightning current injection will significantly improve, but due to the spark discharge of the soil. The ground potential does not increase exponentially with potential lightning current amplitude. The smaller the mesh size, the better the ground potential attenuation. For example of the lightning current 20 kA and the soil resistivity 100 Ω·m, the ground potential of the 5 m×5 m mesh decreases 22.3% compared with the 10 m×10 m mesh. (2) The study finds that the ground potential attenuation away from the lightning strike point at 15 m basically reaches the maximum, which is about 89%. And the degree of attenuation is independent of lightning current amplitude. (3) The results are mainly used for optimization program and design fields on substation lightning protection and grounding.     

The influence of personality on acceptability of sustainable transport policies

Previous research has shown that fairness, infringement on freedom, and perceived effectiveness are determinants of transport pricing acceptability. In the present study we investigate determinants of acceptability of environmental (carbon) taxation for which trust in government and environmental concern are additional determinants. Carbon taxation is an extension of fuel taxes and may thus be viewed as transport pricing. Our main focus is on the role played by personality traits. Structural equation modeling reveals that acceptability is related to the personality traits extraversion, agreeableness, and conscientiousness. Extraverted individuals have higher levels of trust in government which leads to higher acceptability. Also correlations between agreeableness and conscientiousness as well as environmental problem awareness and personal norm are observed. We discuss strategies for effective marketing of transportation policies considering how acceptability is related to personality traits.