Travel behaviour and the total activity pattern

In the past years the behavioural basis of travel demand models has been considerably extended. In many cases individual behaviour is taken as the starting point of the analysis. Conventional aggregate models have been complemented by disaggregate models. However, even in most disaggregate models there is still the well-known sequence of generation, distribution, mode split, and assignment. In fact, travel behaviour is isolated from other human activities, and analyzed separately. The alternative is to take the general activity pattern of individuals as the departure point, and to consider travel as a derived demand. The basis of this study are diaries, kept during a full week on the basis of quarter hours by a sample of approximately 1100 persons.First, results with respect to travel frequency and travel time are given. Secondly, the influence of car availability and degree of urbanisation on travel behaviour is studied. Next, the population is divided into five person categories, and the travel pattern and activity pattern are studied separately per person group. Finally, links between travel and other activities are tentatively established.     

Modeling intrametropolitan industrial location realistically

This paper compares intrametropolitan industrial location models to the process of intrametropolitan industrial location as described in the real estate and urban economic literature. It identifies seven areas where industrial location models are at odds with reality, and suggests ways to make them realistic. Specifically, it makes a case for microanalytic/stochastic/recursive/dynamic/economic industrial location models. It goes on to describe an operational model that is realistic in most respects.     

多功能摊铺机作业参数对道路施工质量的影响

多功能摊铺机熨平工作装置的振捣频率和振幅对摊铺层的平整度和密实度的影响是非常大的。通过对多功能摊铺机实验，针对不同的摊铺材料，调节振捣装置的振捣频率和振幅，实验获取最佳的摊铺作业参数，为多功能摊铺机工作参数设计提供重要的依据。     

间歇式沥青混凝土搅拌设备验收方法的确定

沥青搅拌设备整机验收一般应针对主要作业性能指标进行。科学合理地确定验收项目及验收依据是验收工作的关键，根据实践经验，提出了一套切实有效的验收方法。     

平地机施工时平整度的控制与施工工艺

以“二级公路”施工为分析点，对平地机的特点进行分析，对施工工艺加以总结，就如何提高平地机的使用效率，如何提高其施工过程的平整度，如何达到所规定的质量技术指标进行探讨。     

汽车车身复杂钣金件的拓扑优化设计

利用有限元方法，结合零件的造型、约束、受力和模态等特点，对汽车车身复杂钣金件进行了拓扑分析和设计。利用激光模态分析仪对实物进行了模态测量，分析结果和测量结果基本一致。从而验证了拓扑优化方法可以用于复杂钣金件的设计，并可以获得最佳的结构和力学特性。     

柴油-酒精混合燃料发动机的性能研究

在分析柴油—酒精混合燃料物理化学特性的基础上，研究了不同混合比例的柴油—酒精混合燃料发动机的性能。研究表明：柴油醇燃料发动机的有效燃油消耗率较柴油机的升高，而有效能耗率有一定程度的降低；发动机的碳烟排放明显降低，在保持同样排温的前提下，其功率有一定程度的升高，尾气排放明显降低；柴油机使用混合燃料后，滞燃期延长，燃烧持续期缩短。在采用推迟供油的条件下，柴油—酒精混合燃料发动机的尾气排放性能可以得到较大幅度的提高。     

微型电动轿车车身骨架结构分析

利用ANSYS软件对某进口微型电动轿车车身骨架进行了强度、刚度和模态计算：分析了电动轿车车身骨架的结构特点和电瓶盒等钣金件的影响，提出了独立悬架边界条件的模拟方法。