Precise and reliable positioning based on the integration of navigation satellite system and vision system

In this paper, we propose a precise and reliable positioning method for solving common problems, such as a navigation satellite’s signal occlusion in an urban canyon and the positioning error due to a limited number of visible navigation satellites. This is an integrated system of the navigation satellites system and a vision system. In general, the navigation satellite positioning system has a fatal weakness in that it can not calculate a position coordinate when its signal is occluded by some obstacle. For this reason, positioning by using the navigation satellites system can not be used for a variety of applications. Therefore, we propose as a method to integrate both the navigation satellites system and the vision system. Some target objects that have accurate position coordinates, for example, in an outdoor shaded area like an urban canyon, are installed into the vision system. When the vision system recognizes a target object it loads the accurate coordinate of that target object. Then, it measures the distance by using the disparity from the camera sensor to the target object. These distance and object coordinate data are used for positioning with the navigation satellites system’s data. This integrated system can be used for the positioning solution where the user is in unfavorable conditions. This paper shows that the algorithm of integrated system and the numerical test performed. The results indicate that the reliable and stable positioning can be obtained by introducing the vision system to the satellite navigation system.     

Micro deformation of automobile hood in dipping process using stiffness

Technicians have been going through trial-and-error processes to solve very small or micro deformation on automobile hood during the painting process. In order to establish a systematic improvement procedure which can replace the time-consuming trial-and-error method to reduce defects, an accurate analysis of how micro deformation occurs during the painting process is needed. We have utilized a stiffness scanning method in automobile hood and reverse engineering to build up a reliable and accurate structural analysis and measurement procedures. We measured the load-stroke data at critical locations on automobile hood through stiffness scanning to determine material constants closest to the measurement by assuming several critical hood parts, such as sealer inside the hood, hemming part, spot weld part, and other uncertain joints, as virtual elastic materials. After setting the difference between analytical and measured load-stroke data as an objective function, we computed and minimized it by using the response surface method and partial differentiation of the object function. As a result, by obtaining the reliability was over 91%, which showed a strong correlation between analysis and measured results. By comparing the actual strain measured in real painting lines with calculated strain, we confirmed the validity of our structural analysis method. It was concluded that the proper analysis tool could be utilized in determination of optimal locations of supports during the painting process.     

Characteristics on NOx adsorption and intermediates of LNT catalyst

Several NOx reduction technologies under development in recent years have now been commercialized, including selective catalytic reduction (SCR) with NH₃ or hydrocarbons, and Lean NOx Trap. The aim of the present study is to investigate characteristics on NOx adsorption according to the oxygen concentration, de-NOx performance according to lean/rich injection cycle and toxic intermediates at LNT downstram for lean-burn gasoline engine. Under oxygen of 6%, NOx storage capacity was the highest, showed the highest NOx conversion of 98%. The reason for this phenomena is because the excited oxygen atoms at high oxygen concentration increased oxidizing power of NO. Under low temperature of 205°C, LNT catalyst showed the least NOx conversion of 14% because its activity became lower, while the generation rate of toxic HNCO was highest as CO which is generated during the rich condition, reacts with NOx stored on Ba site.     

Using BDI agents to improve driver modelling in a commuter scenario

The use of multi-agent systems to model and to simulate real systems consisting of intelligent entities capable of autonomously co-operating with each other has emerged as an important field of research. This has been applied to a variety of areas, such as social sciences, engineering, and mathematical and physical theories. In this work, we address the complex task of modelling drivers’ behaviour through the use of agent-based techniques. Contemporary traffic systems have experienced considerable changes in the last few years, and the rapid growth of urban areas has challenged scientific and technical communities. Influencing drivers’ behaviour appears as an alternative to traditional approaches to cope with the potential problem of traffic congestion, such as the physical modification of road infrastructures and the improvement of control systems. It arises as one of the underlying ideas of intelligent transportation systems. In order to offer a good means to evaluate the impact that exogenous information may exert on drivers’ decision making, we propose an extension to an existing microscopic simulation model called Dynamic Route Assignment Combining User Learning and microsimulAtion (DRACULA). In this extension, the traffic domain is viewed as a multi-agent world and drivers are endowed with mental attitudes, which allow rational decisions about route choice and departure time. This work is divided into two main parts. The first part describes the original DRACULA framework and the extension proposed to support our agent-based traffic model. The second part is concerned with the reasoning mechanism of drivers modelled by means of a Beliefs, Desires, and Intentions (BDI) architecture. In this part, we use AgentSpeak(L) to specify commuter scenarios and special emphasis is given to departure time and route choices. This paper contributes in that respect by showing a practical way of representing and assessing drivers’ behaviour and the adequacy of using AgentSpeak(L) as a modelling language, as it provides clear and elegant specifications of BDI agents.     

Computational model for analyzing the kinematics and compliance characteristics of a commercial vehicle’s front suspension system

This paper develops a computational model that can analyze the kinematics and compliance characteristics of the front suspension of a commercial vehicle. This computational model is called the flexible multi-body dynamic model because it is developed by interfacing the finite element model of the multi-leaf spring with the dynamic model of the front suspension. In this paper, the bump mode and roll mode tests are performed with a suspension parameter measuring device (SPMD). An excitation load for creating the bump mode and roll mode motion is applied on the left and right tires slowly in in-phase and out-of-phase modes. In the test, wheel rate, toe angle change, caster angle change, and camber angle change, which together represent the wheel alignment, are measured along with the longitudinal and lateral wheel center loci which together represent the wheel center trajectory change. The reliability of the developed computational model is verified by comparing the simulation results with the SPMD test results. The developed flexible multi-body computational model will provide useful information on kinematics and compliance characteristics in the earliest stages of the commercial vehicle design process.     

Modeling and control of an anti-lock brake and steering system for cooperative control on split-mu surfaces

The brake and steering systems in vehicles are the most effective actuators that directly affect the vehicle dynamics. In general, the brake system affects the longitudinal dynamics and the steering system affects the lateral dynamics; however, their effects are coupled when the vehicle is braking on a non-homogenous surface, such as a split-mu road. The yaw moment compensation of the steering control on a split-mu road is one of the basic functions of integrated or coordinated chassis control systems and has been demonstrated by several chassis suppliers. However, the disturbance yaw moment is generally compensated for using the yaw rate feedback or using wheel brake pressure measurement. Access to the wheel brake pressure through physical sensors is not cost effective; therefore, we modeled the hydraulic brake system to avoid using physical sensors and to estimate the brake pressure. The steering angle controller was designed to mitigate the non-symmetric braking force effect and to stabilize the yaw rate dynamics of the vehicle. An H-infinity design synthesis was used to take the system model and the estimation errors into account, and the designed controller was evaluated using vehicle tests.     

Lateral controller design for an unmanned vehicle via Kalman filtering

This paper proposes a lateral control system for an unmanned vehicle that is designed to improve the responsiveness of the system with the use of a PD control. The vehicle heading error can be stabilized, and the transient response characteristics can be improved using the proposed controller. A mathematical model of the vehicle dynamics using two degrees of freedom was developed for the controller design. The waypoint tracking method for autonomous navigation was tested with incorporation of the Point-to-Point algorithm with position and heading measurements received from GPS receivers via Kalman filtering. The performance of the designed controller was verified through experiments with a real vehicle.     

Design optimization of an injection mold for minimizing temperature deviation

The quality of an injection molded part is largely affected by the mold cooling. Consequently, this makes it necessary to optimize the mold cooling circuit when designing the part but prior to designing the mold. Various approaches of optimizing the mold cooling circuit have been proposed previously. In this work, optimization of the mold cooling circuit was automated by a commercial process integration and design optimization tool called Process Integration, Automation and Optimization (PIAnO), which is often used for large automotive parts such as bumpers and instrument panels. The cooling channels and baffle tubes were located on the offset profile equidistant from the part surface. The locations of the cooling channels and the baffle tubes were automatically generated and input into the mold cooling computer-aided engineering program, Autodesk Moldflow Insight 2010. The objective function was the deviation of the mold surface temperature from a given design temperature. Design variables in the optimization were the depths, distances and diameters of the cooling channels and the baffle tubes. For a more practical analysis, the pressure drop and temperature drop were considered the limited values. Optimization was performed using the progressive quadratic response surface method. The optimization resulted in a more uniform temperature distribution when compared to the initial design, and utilizing the proposed optimization method, a satisfactory solution could be made at a lower cost.     

Research on the Brayton cycle design conditions for reliquefaction cooling of LNG boil off

This paper analyses the Brayton cooling cycle for the reliquefaction of the boil off on liquefied natural gas (LNG) vessels. By performing a thermodynamic study, we analysed and evaluated the conditions, parameters and energy consumption required in the process, including the influence of the choice and variation of diverse factors on the operating conditions and power.     

Dynamic Stability of Vehicle Systems via Poincaré Maps

Computer simulations of a driven vehicle are performed to assess and quantify the automobile stability. The analytical methodology is based on PoincarS maps and Floquet theory, which are commonly used to investigate the stability of periodic systems. The approach accommodates the study of the complex dynamics of vehicle locomotion under various configurations of the system. The proposed method does not require any knowledge regarding the inner structure of the vehicle model. Kinematic data is simply collected at the specific instants to conduct the analysis. It is found that this method has the potential for real time warning and control of vehicle instabilities.