A Multi-Spoke, Three Plane Tyre Model for Simulation of Transient Behaviour

Based on the multi-spoke, single-plane, steady-state tyre model, a transient multi-spoke, three-plane tyre model is presented. This model involves updating the states of all the spokes under consideration to t+dt from the corresponding states at t. Also, a spoke base, which has lateral and longitudinal flexibilities relative to wheel hub, is included. By adding two extra planes of spokes to the original one, the effect of tyre width is built into the model. The three planes are equally spaced across the width of the tyre. The interaction with the ground of the spokes on these three planes is used to represent that of tyre elements at different locations across the width. Analytical results show good qualitative agreement with published experimental data. This model can be used to illustrate transient tyre behaviour and in simulations in which a generic tyre will suffice.     

Flexible long range planning using low cost information

Contemporary transport planning requires a flexible modelling approach which can be used to monitor the implementation of a long term plan checking regularly its short term performance with easily available data; the original model is periodically updated using low cost information and this allows the evaluation of the changes to the plan which may be required. Such an approach requires models suited to regular updating and to the use of data from different sources. Models to update trip matrices from traffic counts have been available for some time; however, the estimation and/or updating of other model stages with low cost data has escaped analytical treatment. The paper discusses this idea and formulates the updating problem for an example involving a joint destination/mode choice model under various assumptions about the nature of the available data. Analytical solutions are proposed as well as some general conclusions.requests for offprints     

Assessment of the volume of fluid method for free-surface wave flow

This study was concerned with the free-surface wave flow around a surface-piercing foil. The volume of fluid method implemented in a Navier–Stokes computational fluid dynamics code was employed. Three widely used discretization schemes for the volume of fluid method were assessed for a test case that involved general ship waves, spilling breaking waves in front of the leading edge, and bubbly free surfaces in separated regions. A single computational approach was selected for the comparison, and a grid-dependence study was carried out. The computational results were validated against existing experimental data, showing good agreement. The validation results suggest that all three discretization schemes perform well, but the best and most efficient results were obtained using the high-resolution interface capturing scheme.     

Airline emission charges: Effects on airfares,service quality,and aircraft design

This paper explores the effect of airline emissions charges on airfares, airline service quality, aircraft design features, and network structure, using a detailed and realistic theoretical model of competing duopoly airlines. These impacts are derived by analyzing the effects of an increase in the effective price of fuel, which is the path by which emissions charges will alter airline choices. The results show that emission charges will raise fares, reduce flight frequency, increase load factors, and raise aircraft fuel efficiency, while having no effect on aircraft size. Given that these adjustments occur in response to the treatment of an emissions externality that is currently unaddressed, they represent efficient changes that move society closer to a social optimum.     

Circumventing the weight-versus-footprint tradeoffs in vehicle fuel economy regulation

China, Japan, and the European Union use weight-based fuel economy standards, whereas the US Department of Transportation favors footprint-based standards. In this paper we offer a way of reconciling these approaches. Weight-based standards tend to focus regulatory incentives on technology rather than downsizing, but they provide no incentive for weight reduction. Footprint-based standards, by contrast, motivate vehicle manufacturers to reduce weight without reducing footprint, but only to the extent that they are also motivated to increase footprint without increasing weight. Neither approach discriminates between beneficial and detrimental weight-changing strategies. However, the tradeoffs between weight and footprint can be circumvented by employing a weight-based standard, which does not create weight-changing incentives, in combination with complementary regulatory measures that would be focused specifically and exclusively on motivating beneficial weight reduction strategies.     

Location of bus garages

The location of bus garages is a complex issue that has received recent attention in the literature. Given a bus system, the number of bus garages and their locations depend on garage cost, deadheading cost and environmental impacts. An approximate analytical model is used to determine the number of bus garages that minimizes the above costs. The concept of a slowly varying density of bus-route origins (hence deadheads) per unit area is used to model deadheading costs. The increased deadheading caused by breakdowns and accidents is also considered. The garage cost is modeled as a function of the number of buses stored. A closed-form solution is obtained for the optimal density of garages, when the garage cost function is linear. The actual locations of garages and the allocations of buses to the garages are found using a discrete space location-allocation model formulated so as to consider the environmental impact associated with buses deadheading through populated neighborhoods.     

Influence of vehicular traffic on urban air quality – A case study of Hyderabad,India

In the present study, impact of vehicular traffic emissions on black carbon aerosol mass concentration, trace gases and ground reaching solar radiation were analyzed during nationwide truck strike of 5–12 January, 2009 over urban environment of Hyderabad, India. A significant reduction of about 57%, 60%, 40% and 50% was observed in black carbon, particulate matter, carbon monoxide and ozone respectively during nationwide truck strike period. Results of the study are important for source apportionment of pollutants as the strike created natural laboratory for studying the impact of diesel operated trucks on urban air quality.     

Alternative Modeling Approaches Used for Examining Automobile Ownership: A Comprehensive Review

Abstract

Household vehicle ownership, and the associated dimensions including fleet size, vehicle type and usage, has been one of the most researched transport topics. This paper endeavors to provide a critical overview of the wide-ranging methodological approaches employed in vehicle ownership modeling depending on the ownership representation over the past two decades. The studies in the existing literature based on the vehicle ownership representation are classified as: exogenous static, exogenous dynamic, endogenous static and endogenous dynamic models. The methodological approaches applied range from simple linear regressions to complex econometrics formulations taking into account a rich set of covariates. In spite of the steady advancement and impressive evolution in terms of methodological approaches to examine the decision process, we identify complex issues that pose a formidable challenge to address the evolution of vehicle ownership in the coming years. Specifically, we discuss challenges with data availability and methodological framework selection. In light of these discussions, we provide a decision matrix for aiding researchers/practitioners in determining appropriate model frameworks for conducting vehicle ownership analysis.     

Application of genetic algorithms for joint optimization of signal setting parameters and dynamic traffic assignment for the real network data

This paper presents the joint optimization of signal setting parameters and dynamic user equilibrium (DUE) traffic assignment for the congested urban road network. The simulation-based approach is employed to obtain the DUE condition for the case of multiple-origin multiple-destination traffic flows. The dynamic traffic assignment simulation program (DTASP), developed in C language is used to assign the traffic dynamically on the road network, whereas method of successive averages (MSA) is modified and used to arrive at the DUE condition. The artificial intelligence technique of genetic algorithms (GAs) is applied to obtain the optimal signal setting parameters and path flow distribution factor for DUE condition. The methodology developed in such a way that joint optimization of signal setting parameters with DUE is obtained. The proposed method is applied to the real network data of Fort Area of Mumbai city comprising of 17 nodes and 56 unidirectional links with 72 Origin–Destination pairs, where all the 17 nodes are signalized intersections. The traffic flow condition for the optimized signal setting parameters is considerably improved compared to the existing signal settings. The results prove that the GA is an effective technique to solve the joint optimization problem for the real network data.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.