Pragmatic Tyre Model for Short Wavelength Side Slip Variations

The first-order relaxation length concept is often used to model transient tyre behaviour. It gives a rather good representation of the lateral force response, also at shorter wavelengths. The self aligning moment appears to behave rather differently and its responses cannot be represented by a relaxation length system only. Based on the analytical frequency response functions of the pneumatic trail of the brush type tyre model, a new pragmatic approach is developed. The model consists of a phase leading system in series with the first-order model for the lateral force. The results are compared to the responses of a discrete brush type simulation model. It appears that the aligning moment can be represented by this new pragmatic model very well.     

Braking Force Distribution Control for Improved Vehicle Dynamics and Brake Performance

This paper describes the feasibility of improving the braking performance of a commercial vehicle by using an electronic braking system. An electronic braking system enables the braking force at each wheel to be independently controlled. Braking force distribution control makes the braking force at each wheel proportional to each wheel's load. Results of computer simulation and vehicle test showed that the proposed control laws can eliminate the effects of a laden condition on the braking distance and can increase the degree of deceleration at which wheel lock occurs, resulting in improved vehicle attitude stability during a critical maneuver.     

Two alternative definitions of traffic equilibrium

The paper shows that, under reasonable conditions, if there are junction or modal interactions then a Wardrop equilibrium exists but a user—optimised flow may well not.     

Fatigue analysis for a multi-lap spot welded joint of high strength steel using quasi static tensile-shear test

The welding quality of spot weldment is an important factor that significantly affects the strength, stiffness, safety, and other performance characteristics of vehicles. Therefore, quality control and fatigue life evaluation of spot weldment are necessary processes. This paper presents a method for determining the fatigue life of multi-lap spot weldment of a high strength steel sheet. In this method, the fatigue life is estimated using the lethargy coefficient, which is the total defect coefficient according to rupture stress and time obtained by the quasi static tensile-shear test. The DC potential drop method was used to check initiation and propagation of cracks in addition to the test. Also, in this study, we modified the lethargy coefficient by using the welding current. Furthermore, we define a specific lapping constant, which is a characteristic constant of 2 or 3 lap weldments. The fatigue life obtained by the fatigue estimate equation, which contains a specific lapping constant was compared and verified with an experimental value. Finally we analyzed the relation of lap number, welding current and fatigue life. This method can save processing time and cost for predicting the life cycle of a structure.     

Experimental investigation and comparison of nanoparticle emission characteristics in light-duty vehicles for two different fuels

In recent years, particle number emissions rather than particulate mass emissions in automotive engines have become the subject with controversial discussions. Recent results from studies of health effects imply that it is possible that particulate mass does not properly correlate with the variety of health effects attributed to engine exhaust. The concern is now focusing on nano-sized particles emitted from I. C. engines. In this study, particulate mass and particle number concentration emitted from light-duty vehicles were investigated for a better understanding of the characteristics of the engine PM from different types of fuels, such as gasoline and diesel fuel. Engine nano-particle mass and size distributions of four test vehicles were measured by a condensation particle counter system, which is recommended by the particle measurement program in Europe (PMP), at the end of a dilution tunnel along a NEDC test mode on a chassis dynamometer. We found that particle number concentrations of diesel passenger vehicles with DPF system are lower than gasoline passenger vehicles, but PM mass has some similar values. However, in diesel vehicles with DPF system, PM mass and particle number concentrations were greatly influenced by PM regeneration. Particle emissions in light-duty vehicles emitted about 90% at the ECE15 cycle in NEDC test mode, regardless of vehicle fuel type. Particle emissions at the early cold condition of engine were highly emitted in the test mode.     

Range Extender Module Transmission Topology Study

Range extender modules are one option to compensate for short drive ranges of electric vehicles. The close interaction of combustion engine and generator poses new challenges in development. A key requirement for range extender systems is to be light and virtually imperceptible in operation. High-speed electrical machines aim at increasing power density. However, their introduction in a range extender requires a gearbox. The combustion engine torque fluctuations can lead to rattle in the gearbox. The rattle can be overcome by a dual mass flywheel. An interdisciplinary model is developed and used to analyse three different range extender systems: one with a low speed generator without gearbox, one with a high-speed generator, and one with a high-speed generator and a dual mass flywheel. The efficiency was found to be higher for the system with a low speed generator, whereas the power density and the costs are beneficial for the high-speed concept. A dual mass flywheel eliminates the changes of torque direction in the gearbox. It reduces the speed fluctuations of the gearbox and generator by over 90 % compared to the low speed setup. But it increases rolling moment and subsequently chassis excitation compared to a setup with only a gearbox.     

缓和曲线对交通安全的影响分析

对比分析文献表明,不合理的缓和曲线长度会影响驾驶行为和交通安全。调查分析了上三高速公路的39个弯道和2001年—2004年事故资料、沪杭高速公路浙江段的5个弯道和1999年—2004年事故资料、杭宁高速公路浙江段的6个弯道和2001年—2004年事故资料,其中缓和曲线交通事故并没有出现异常现象,表明其缓和曲线长度设计是合理的、可行的,没有对交通安全造成明显影响。在所调查的半径范围[400 m,3819.516 m],缓和曲线参数A与圆曲线半径R之比(A/R)随半径增大而呈现较好的负次幂递减规律,而且其变化范围基本上在1/3~1/2,这与传统认识及最近文献调查相一致。这一基本规律可为设计提供更明确的量化参考依据。     

Breaking car use habits: The effectiveness of a free one-month travelcard

Based on calls for innovative ways of reducing car traffic and research indicating that car driving is often the result of habitual decision-making and choice processes, this paper reports on a field experiment designed to test a tool aimed to entice drivers to skip the habitual choice of the car and consider using—or at least trying—public transport instead. About 1,000 car drivers participated in the experiment either as experimental subjects, receiving a free one-month travelcard, or as control subjects. As predicted, the intervention had a significant impact on drivers’ use of public transport and it also neutralized the impact of car driving habits on mode choice. However, in the longer run (i.e., four months after the experiment) experimental subjects did not use public transport more than control subjects. Hence, it seems that although many car drivers choose travel mode habitually, their final choice is consistent with their informed preferences, given the current price–quality relationships of the various options.