修理用统一型薄轮缘车轮踏面外形

针对运用中因轨距减小而导致轮缘磨加剧的问题，设计并试验了统一型减薄轮缘厚度的修理用车轮踏面外形，试验表明，对减少轮缘磨耗，延长车轮使用寿命均有明显效果。     

A probabilistic damage tolerance concept for welded joints Part 2: a supplement to the rule based S–N approach

The first part of this paper presented the required statistics and stochastic models for reliability analysis of the fatigue fracture of welded plate joints. This present Part 2 suggests a probabilistic damage tolerance supplement to the design S–N curves for welded joints. The goal is to provide the practising engineer with simple tools that predict the reliability against fatigue fracture during service life. The impact of the chosen fatigue design factors (FDF) and the uncertainty in the applied stresses is revealed. The effect of an in-service inspection programme is also predicted. The results are presented as dimensionless matrices and suggested for use in support of decision-making at the design stage, without any advanced fracture mechanics modelling and stochastic simulation. One important advantage of this format is that the probability levels are presented regardless of actual weld class and target service life (TSL). This is obtained by introducing the FDF as a key parameter to the results. This parameter is defined as the ratio of predicted fatigue life over TSL. FDF is always calculated in the S–N approach which is mandatory in fatigue life prediction. Various welded details (classes) will have the same reliability level for the same FDF. This is true at the end of TSL and at earlier stages, i.e. fractions of TSL. The absolute value of TSL is immaterial for a given FDF. In the case of in-service inspection, the inspection interval is also given without dimensions as a fraction of TSL.

Only the influence of future scheduled inspections is treated. Updating based on actual inspection results is not included as the scope of work is inspection planning at the design stage. Results for some frequent cases occurring in practice are readily derived and presented.     

Design and shared use of a terminal departure lounge for new large aircraft operations

New Large Aircraft (NLA) are new aircraft developments larger than any existing aircraft. The NLA's higher seat capacity will significantly impact passenger terminal design and operations. This paper focuses on the issues regarding the departure lounge. Deterministic queuing theory is used to determine the size and seating configuration of the lounge, as well as to decide whether a second level should be built to accommodate the increase in the number of passengers. The paper also discusses the use of the satellite section of a pier‐satellite terminal as a single lounge for the NLA. Spreadsheets are used to implement the analyses.     

Urban form,travel time,and cost relationships with tour complexity and mode choice

The primary purpose of this study was to investigate how relative associations between travel time, costs, and land use patterns where people live and work impact modal choice and trip chaining patterns in the Central Puget Sound (Seattle) region. By using a tour-based modeling framework and highly detailed land use and travel data, this study attempts to add detail on the specific land use changes necessary to address different types of travel, and to develop a comparative framework by which the relative impact of travel time and urban form changes can be assessed. A discrete choice modeling framework adjusted for demographic factors and assessed the relative effect of travel time, costs, and urban form on mode choice and trip chaining characteristics for the three tour types. The tour based modeling approach increased the ability to understand the relative contribution of urban form, time, and costs in explaining mode choice and tour complexity for home and work related travel. Urban form at residential and employment locations, and travel time and cost were significant predictors of travel choice. Travel time was the strongest predictor of mode choice while urban form the strongest predictor of the number of stops within a tour. Results show that reductions in highway travel time are associated with less transit use and walking. Land use patterns where respondents work predicted mode choice for mid day and journey to work travel.

Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.     

Auto-ignition and micro-explosion behaviors of droplet arrays of water-in-fuel emulsion

The characteristics of auto-ignition and micro-explosion behaviors of one-dimensional arrays of fuel droplets suspended in a chamber with high surrounding temperature were investigated experimentally with various droplet spacings, numbers of droplet and surrounding temperatures. The fuels used were pure n-decane and emulsified n-decane with varied water contents ranging from 10 to 30%. All experiments were performed under atmospheric conditions with high surrounding temperatures. An imaging technique using a high-speed camera was adopted to measure ignition delay, flame lifetime, and flame spread speed. The camera was also used to observe micro-explosion behaviors. As the droplet array spacing increased, the ignition delay also increased, regardless of water content. However, the lifetime of the droplet array decreased as the droplet spacing increased. The micro-explosion starting time remained unchanged regardless of the number of the droplets or the droplet spacing; however, it tended to be delayed slightly as the water percentage and droplet spacing increased.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

Links between subjective and objective evaluations regarding the steering character of automobiles

This work presents an experiment on the relationships between subjective and objective evaluations of vehicle handling. Ten cars were examined objectively in several open-loop driving dynamics manoeuvres and subjectively by test persons in typical traffic situations. Results are extracted from a stationary test (the Slowly Increasing Steer Test), and a dynamical test (the Frequency Response Test). The subjective measurements are obtained from drivers on a rural road course via a questionnaire, which was developed to separately investigate the quantity level perception, the so-called “Niveau”, and the more qualitative “Liking”. These subjective “measurements” are embedded into a two-channel definition of “Steering Comfort” as a genus for “Steering Discomfort” and “Character”. The article concentrates on developing a statistical method for the consideration of correlations amongst the subjective/objective data. In doing so, the variance in example subjective Niveau ratings can be significantly explained by several objective quantities. Indicators for co-domains of validated discomfort characteristics and hints for endeavouring character Liking ranges are detected.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Effect on friction of engine oil seal with engine oil viscosity

Low viscosity engine oil can improve a vehicle’s fuel economy by decreasing the friction between the engine components. Frictional torque varies with the velocity change due to different viscosity characteristics of SAE grade 5W-20, 5W-30 and 5W-40 engine oils. The viscosity for each of these grades was measured to outline the effect low viscosity engine oils have on engine friction, which may lead to improved fuel economy. Engine oil seal frictional torque increases with the shaft rotational speed for all three engine oil grades. A decrease in engine oil seal frictional torque was confirmed when low viscosity engine oil was used. Also, the leak-free performance of the engine oil with the seal satisfied the life limit durability test criteria. Thus, low viscosity engine oil may be used to improve fuel economy by decreasing the frictional loss of the engine oil seal while having no negative impact on performance due to leak-free functioning.