地铁车站建筑形态的自明性与差异性

从地铁车站建筑的特性出发,结合目前国内地铁车站建筑现状,分析车站建筑形态的自明性表现,总结分析营造车站建筑的差异性的三种典型处理手法,探讨以可持续设计观念来实现车站建筑技术与人文精神的结合。     

Determining the hydrodynamic forces on a planing hull in steady motion

A combination of methods was developed that can determine hydrodynamic forces on a planing hull in steady motion. Firstly, a potential-based boundary-element method was used to calculate the hydrodynamic pressure, induced resistance and lift. Then the frictional resistance component was determined by the viscous boundary layer theory. Finally, a particular empirical technique was applied, to determine the region of upwash geometry and determine spray resistance. Case studies involving four models of Series 62 planing craft were run. These showed that the suggested method is efficient and capable, with results that are in good agreement with experimental measurements over a wide range of volumetric Froude numbers.     

SMA改良油田公路路面材料的试验研究

随着克拉玛依经济飞速发展，交通量日趋加大，道路面临的压力越来越大，交通的迅猛发展对路面材料的性能提出了更高的要求。沥青玛蹄脂碎石混合料（StoneMatrixAsphalt，缩写为SMA）是近年来在国际上出现的一种非常引人注目的新型沥青混合料，从SMA混合料配合比设计的角度论述了如何确保SMA优异路面使用性能的发挥。     

Discomfort of vertical whole-body shock-type vibration in the frequency range of 0.5 to 16 Hz

Shock-type vibrations are frequently experienced in vehicles excited by impulsive input, such as bumps in the road, and cause discomfort. Current national and international standard weightings were primarily developed for assessing exposure to sinusoidal or random vibrations and not impulsive excitations or shocks. In this experimental study, various shock signals were systematically produced using the response of a one degree-of-freedom vibration model to hanning-windowed half-sine force input. The fundamental frequency of the shock was varied from 0.5 to 16 Hz at a step of 1/3 of an octave. The magnitude estimation method was used for fifteen subjects to compare the discomfort of shocks with various unweighted vibration dose values between 0.35 ms^−1.75 and 2.89 ms^−1.75 at each frequency. The equivalent comfort magnitude of shock showed greater sensitivity at frequencies less than 0.63 Hz and at the resonance frequency of the human body between 5.0 Hz and 6.3 Hz. The frequency weighting constructed by using both the equivalent comfort magnitude and the growth rate of discomfort obtained in this study was compared with the current standard weightings, W_b of BS 6841 and W_k of ISO 2631. The derived weightings for shock were applied to the acceleration of the shocks, and an enhanced correlation was proved between the magnitude estimations and the weighted physical magnitude of shock.     

Study on Tire Dynamic Cornering Properties Using Experimental Modal Parameters

Based on the modeling of tire vertical characteristics and steady cornering properties, the model of tire nonsteady cornering is established in this paper using tire modal parameters extracted experimentally. In order to consider the influence of tire rolling effect on its cornering properties, the induced transfer function is introduced. The analytical formulae for calculation of transfer-function of lateral force and self-aligning torque with respect to lateral displacement and yaw angle are derived. The nonsteady cornering characteristics of tire under different loads can be calculated. The results of calculation are consistent with the experimental ones in the literature. The influence of rolling speed on tire cornering properties including the static case is analyzed. The nonsteady cornering properties in high frequency range are given by the model. The study demonstrates the consistency between steady and nonsteady tire modeling by using modal parameters.     

Pole location control design of an active suspension system with uncertain parameters

This paper addresses the problem of robust control design for an active suspension quarter-car model by means of state feedback gains. Specifically, the design of controllers that assure robust pole location of the closed-loop system inside a circular region on the left-hand side of complex plane is investigated. Three sufficient conditions for the existence of a robust stabilizing state feedback gain are presented as linear matrix inequalities: (i) the quadratic stability based gain; (ii) a recently published condition that uses an augmented space and has been here modified to cope with the pole location specification; (iii) a condition that uses an extended number of equations and yields a parameter-dependent state feedback gain. Unlike other parameter-dependent strategies, neither extensive gridding nor approximations are needed. In the suspension model, the sprung mass, the damper coefficient and the spring constant are considered as uncertain parameters belonging to a known interval (polytope type uncertainty). It is shown that the parameter-dependent gain proposed allows one to impose the closed-loop system pole locations that in some situations cannot be obtained with constant feedback gains.     

Hierarchical optimisation of the design parameters of a vehicle suspension system

This paper presents a design methodology for the mechanical systems entitled First Design. It is based on a hierarchical organisation of the design, taking into account the notion of robustness at an early phase of the project. The aim is to improve the quality of the system in order to make it robust, less sensitive to the variability of the external parameters and design parameters. We distinguish two main stages of the design cycle: one concerning functional parameters and another concerning physical parameters. The methodology is based on simplified models, on sensitivity analysis and on robust multi-objective optimisation. As an example, the methodology will be applied to the optimisation of vehicle suspension system design parameters. For each stage of the hierarchical design, adapted simplified models, sensitivity analyses and optimisation processes will be studied and applied to our vehicle suspension system.     

A General Method for the Evaluation of Vehicle Manoeuvrability with Special Emphasis on Motorcycles

This paper presents a novel approach to the assessment of the manoeuvrability of vehicles which is not based on the simulation of open-loop manoeuvres, nor does it rely on the modelling of the driver as a control system. Instead, the essence of the method is the solution of a two-point optimal control boundary value problem, in which a vehicle, subject to physical constraints like tyre adherence and road borders, among others, is required to go between given initial and final positions as fast as possible. The control inputs - i.e., the driver's actions - that make the vehicle move between the two states in the most efficient way are found as a part of the solution procedure and represent the actions of a sort of ideal, perfect driver . The resulting motion is called the optimal manoeuvre and, besides being the most efficient way that the given vehicle has for travelling between the two points according to the chosen optimal criterion, may be taken as a reference for meaningful comparisons with other vehicles. The value of the penalty function, used to define the optimal condition occurring at the optimal manoeuvre, may be taken as a measure of manoeuvrability or handling. With this approach the manoeuvrability properties are established as intrinsic to the vehicle, being defined with respect to an ideal perfect driver. Some possible forms of the penalty function, which means slightly different concepts of manoeuvrability and handling, are discussed. In the end, the case of motorcycles and some examples of optimal manoeuvres are given.     

泡沫沥青混合料物理力学特性的试验研究

泡沫沥青混合料是一种全新的道路材料，其有关特性尚不完全清楚。本文以泡沫沥青稳定2种骨料(新砂石料和回收料)为基础，从材料的选取与级配的组成、沥青的最佳发泡条件、混合料拌和方法及养护方案等几个方面提出一种泡沫沥青混合料的研究方法，并对该材料的物理性质和强度特性进行了研究。结果表明泡沫沥青混合料密度较小，空隙率较大，其强度能够满足路面设计规范关于基层设计参数的要求。水泥作为填料对泡沫沥青混合料强度影响不大，其主要作用是能显著改善水稳性。