广东LNG干线接收站取水口的设计

结合LNG接收站取水口的使用功能特点和预设施工过程,进行有针对性的结构方案设计.较好地克服了施工过程中遇到的困难,达到了节约成本和缩短工期的目的.     

循环泵叶轮设计问题的探讨

本文针对某产品配套循环泵叶轮的设计过程中出现的问题,在水力设计过程中增加叶轮出口宽度,在叶片绘型中保证流道过流面积随流道中线线性变化,对轴面图中的前盖板轮廓线形状进行修改。重新设计的叶轮使循环泵的水力性能完全达到设计要求。     

快速测定铝／氧化银电池电解液中碱浓度的方法

用传统化学分析方法测量铝／氧化银电池电解质溶液组分浓度耗时长。针对这一弊端,本文提出通过测量电解质溶液密度、温度,然后结合计算出的铝酸盐浓度,再对照在不同温度下电解质溶液密度与铝酸盐浓度关系曲线图,快速确定电解质溶液中碱的浓度的方法。在电池实际放电过程中证明该方法行之有效。     

风浪流联合作用下RMFC码头运动性能试验研究

RMFC码头作为连岸设施,周围布置有锚泊系统,其工作海域水深很浅,深度随距海岸线距离而变化。由于利用多刚体水动力学的计算分析难以保证结果的正确性,因此,采用试验方法研究RMFC码头的运动性能。假定单元间的接头和系泊系统可有效承担风、浪、流诱导产生的载荷,通过试验研究RMFC码头典型单元六自由度运动,以验证此种RMFC码头布置形式的有效性。     

竖向接缝对连续刚构桥长期变形的影响分析

结合施工因素讨论连续刚构桥竖向接缝对成桥后期挠度的影响,同时分析不同施工质量下竖向接缝剪切徐变对后期挠度的贡献．对提高接缝质量具有重要意义。     

基于扩展卡尔曼滤波的GPS信号跟踪技术

提出一种基于扩展卡尔曼滤波的GPS信号跟踪方法,通过扩展卡尔曼滤波器,得到基于相干积分支路的滤波模型,有效地削弱常规GPS跟踪环路中的跟踪误差,增强接收机的抗干扰性能,提升其在信号较弱位置下环路的跟踪性能,对加入惯性信息条件下惯性信息对系统所产生的影响做了相应的分析研究。通过仿真对比结果可以知道:当处于弱信号条件时,与通常用到的GPS信号跟踪方式相比,基于扩展卡尔曼滤波的信号跟踪算法可以有效提升跟踪的精度。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Effect of Explosion in a Gas Pipeline Compartment of a Utility Tunnel on Neighboring Metro Tunnels北大核心CSCD

In this paper the numerical simulation analysis of the effect of explosion in the gas pipeline compartment of a utility tunnel on neighboring metro tunnels was conducted using the software AUTODYN. The results show that the TNT equivalent in a fireproof partition with length of 200 m is 41.6 kg when the gas concentration in the gas pipeline compartment reaches 10%; the blast wave has much effect on the crown and arch waist of the round metro tunnel and it’s necessary to take some protective measures in both areas; when the surrounding soil is sand, the utili- ty tunnel is above the round metro tunnel and their alignments are in the same direction, the greater the vertical spacing between the utility tunnel and the metro tunnel, the smaller the effect of the blast wave on the metro tunnel; when the vertical spacing is 7.2 m, the maximum dynamic tensile stress is 1.86 MPa (including the static stress value of 1 MPa in the tunnel segment) and it is slightly smaller than the designed tensile strength of metro tunnel (about 1.89 MPa). The maximum vibration velocity and the maximum displacement meet the structural stability require- ments, so it is suggested the vertical spacing between the utility tunnel and metro tunnel shall not be less than 7.2 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Mathematically calculating the transit time of cargo through a liner shipping network with various trans-shipment policies

This paper derives the mathematical expressions for the transit time of cargo through a liner shipping network. Main efforts are devoted to deriving the calculation expressions of the connection time of cargo during trans-shipment. For the forward and many-to-one trans-shipment policies, we conduct a minor correction towards the expressions in existing studies to improve the completeness. Meanwhile, we propose an alternative but more straightforward calculation method for connection time which bypasses the complicated inductive argument in existing studies. Then we introduce two new trans-shipment policies: backward trans-shipment and one-to-many trans-shipment, and mathematically calculate the corresponding connection times. Numerical experiments also deliver some managerial insights into the effectiveness of backward trans-shipment in transit time control.     

提高应变梁加工合格率

本文分析了应变梁因平面度超差而出现的质量问题,通过刀具、加工参数等方面改进来提高其加工质量。