Rule-based control of a semi-active suspension for minimal sprung mass acceleration: design and measurement

In this paper, a rule-based controller is developed for the control of a semi-active suspension to achieve minimal vertical acceleration. The rules are derived from the results obtained with a model predictive controller. It is shown that a rule-based controller can be derived that mimics the results of the model predictive controller and minimises vertical acceleration. Besides this, measurements on a test vehicle show that the developed rule-based controller achieves a real-world reduction of the vertical acceleration, which is in agreement with the simulations.     

One-dimensional model on fuel penetration in diesel sprays with gas flow

In diesel engine, spray penetration is usually changed by in-cylinder gas flow. Accurate prediction on diesel spray with gas flow is important to the optimal design of diesel fuel injection system. This paper presents a theory investigation focusing on the penetration of diesel spray with gas flow. In order to understand the effect of gas flow on the penetration of diesel spray, a one-dimensional spray model is developed from an idealized diesel spray, which is able to predict the spray behavior under different gas flow conditions. The ambient gas flow is simplified as ideal flow that has only constant flow velocity along x-axial and y-axial directions of spray. The x-axial and y-axial directions are respectively defined as along and vertical spray directions. The main assumption is that the y-axial direction gas flow has no effect on the penetration of spray along x-axial direction. The principles of conservation of mass and momentum are used in the derivation. Momentum of in-cylinder air flow is also taken into consideration. Validation of the model at stable condition is achieved by comparing model predictions with experimental measurements of diesel spray without gas flow from Naber's experiments. Furthermore, CFD simulations on penetration of diesel spray with gas flow were performed with the commercial code AVL-fire. The onedimensional model is validated by the penetration results with gas flow from CFD calculation. Results show that a reasonable estimation of the spray evolution can be obtained for both with and without ambient gas flow conditions.     

Robust inspection technique for detection of flatness defects of oil pans

This paper discusses two different methods for the detection of flatness defects present on the mounting surfaces of oil pans using laser-scanned point clouds. The first method involves registration, which is a widely used method in the field of 3D data inspection: scanned point clouds are registered with CAD data and the iterative closest point (ICP) algorithm is used for further comparison. The second method is our proposed method, a simple yet effective method for measuring the flatness of an oil pan mounting surface. The process is based on the construction of a reference plane on the scanned surface. The oil pan mounting surface is scanned by a 3D laser scanner, obtaining point cloud data that is then further processed to reduce noise. Using this processed data, a reference plane parallel to the direction of the mounting surface is defined at the mean position of the mounting surface. The direction of the reference plane is determined by the normal vector of the mounting surface. Construction of the reference plane is carried out by the singular value decomposition (SVD) technique. The deviation of the surface from the reference plane is measured by calculating the error distance between the points of the surface to the reference plane using the least-squares method.     

Real-time empirical NO<Subscript>x</Subscript> model based on In-cylinder pressure measurements for light-duty diesel engines

This paper proposes a real-time empirical model of NO_x emissions for diesel engines. The proposed model predicts the level of NO_x emissions using an empirical model developed based on the thermal NO formation mechanism, the extended Zeldovich mechanism. Since it is difficult to consider the exact physical NO formation phenomena in real-time applications, the proposed algorithm adapts the key factors of the NO formation mechanism from the extended Zeldovich mechanism: temperature of the burned gas, concentration of the gas species, and combustion duration where NO is generated. These factors are considered in a prediction model as four parameters: exhaust gas recirculation rate (EGR rate), crank angle location of 50 % of mass fraction burned (MFB50), exhaust lambda value, and combustion acceleration. The proposed prediction model is validated with various steady engine experiments that showed a high linear correlation with the NO_x emission measured by a NO_x sensor. Furthermore, it is also validated for transient experiments.     

Resource-aware integration of AUTOSAR-compliant ECUs with an empirical wcet prediction model

This paper presents an integration method of AUTOSAR-compliant ECUs which can evaluate resource constraints in an early-stage of development. There are three types of resources for an ECU (timing, memory, and interface) which should be carefully managed for successful ECU integration. The proposed method consists of three steps: measurement, prediction, and evaluation. In the first step, a method to measure resource factors for AUTOSAR-compliant software architecture is introduced. Based on the method, a worst-case execution cycle of a runnable, memory section usages of a software component, and interface of legacy ECUs can be obtained. In the second step, the obtained factors are quantitatively predicted according to the architectural designs of the integration ECU. In the case of the timing resource, the worst-case execution time of the integration ECU can be precisely predicted by a proposed empirical model. In the last step, the resource constraints such as CPU, memory, network utilizations can be evaluated with predicted resource factors before implementation. The proposed method was applied to the integration of an in-house engine management system composed of two ECUs. The method successfully provided quantitative measures to evaluate architectural designs of three different integration scenarios.     

不同稳定剂对SBS改性沥青稳定效果的对比研究

通过试验测试不同老化时间样品的针入度、软化点和延度比较其相容性和路用流变学性能指标的变化,分析体系宏观稳定性和稳定剂性能特征,并通过形态结构照片分析稳定剂改善的效果。结果表明,加入稳定剂后改性沥青的高温储存稳定性明显改善,同时加入FD-06无硫稳定剂的改性沥青在热储存过程中性能更加稳定,不易离析。沥青中的部分组份具有化学活性,利用其活性点,引入带有活性基团的反应物,并通过被引入分子的化学结构的调节改善SBS与沥青的相容性,从而制备储存稳定性良好的SBS改性沥青。化学改性技术的应用提高了路用改性沥青的性能/价格比。     

The chatter of racing motorcycles

The chatter of motorcycles appears during braking and consists of a vibration of the rear and front unsprung masses at a frequency in the range of 17-22 Hz depending on the motorcycle. This vibration could be very strong and acceleration of the unsprung masses can reach 5-10 g. The chatter is an auto-excited vibration and this fact explains why it appears suddenly when the mechanism of auto-excitation is generated. This paper presents the chatter phenomenon both from an experimental and a numerical point of view. First, the chatter is defined on the basis of some experimental data from racing motorcycles and from the comments of some racing teams technicians. Then, chatter is analysed in different motion conditions and for different braking styles by means of linear and non-linear simulations of the motorcycle dynamics. A physical interpretation of the phenomenon is also proposed.     

A fundamental investigation of tilt control systems for narrow commuter vehicles

One way of addressing traffic congestion is by efficiently utilizing the existing highway infrastructure. Narrow tilting vehicles that need a reduced width lane can be part of the solution if they can be designed to be safe, stable, and easy to operate. In this paper, a control system that stabilizes the tilt mode of such a vehicle without affecting the handling of the vehicle is proposed. This control system is a combination of two different types of control schemes known as steering tilt control (STC) and direct tilt control (DTC) systems. First, different existing variations of both STC and DTC systems are considered and their shortcomings analysed. Modified control schemes are then suggested to overcome the deficiencies. Then a new method of integrating these two control schemes that guarantees smooth switchover between the controllers as a function of vehicle velocity is proposed. The performance of the proposed STC, DTC, and integrated systems is evaluated by carrying out simulations for different operating conditions and some experimental work. The design of a second-generation narrow tilting vehicle on which the developed control system has been implemented is presented.