Dynamics of inorganic nutrient species in the Bohai seawaters

Within the frame of a Sino-German Joint Research Program, two cruises of “R/V Dong Fang Hong 2” were carried out in September–October 1998 and April–May 1999, respectively, to understand the dynamics of nutrients in the Bohai. Nutrient species (NO₃⁻, NO₂⁻, NH₄⁺, PO₄³⁻ and SiO₃²⁻) are determined colorimetrically on board for five anchor and 30 grid stations. In situ incubation experiments are performed to determine planktonic nutrient uptake and benthic exchange flux. Nutrient concentrations display short-term variability and seasonal change in the Bohai, with higher levels in shallow coastal waters than in the Central Bohai. The influence of riverine discharge on nutrient levels can be seen from salinity isopleths, nutrient distribution and species ratios. Near-bottom (nb) waters have similar nutrient concentrations as to the surface waters in the Central Bohai, whereas stratification takes place in the Bohai Strait and North Yellow Sea. In situ incubation experiments provide evidence that the uptake ratio (i.e. N, P) by phytoplankton is proportional to the ratios among nutrient species in ambient waters. Based on the data of this study and previously publications, a preliminary estimate of nutrient budgets via riverine input and atmospheric deposition is established. The results indicate that atmospheric deposition gains importance over rivers in delivering nutrients into the Bohai and sustain the new production, following recent decrease in riverine inflow caused by drought periods in North China and damming practices. A historical review of nutrient data indicates that concentrations of nitrogen increase and phosphorus and silica decrease in the Central Bohai over last 40 years. This potentially has an important influence on the health of ecosystem in Bohai (e.g. food web and community structure), though further study is needed to examine the scenario in more detail.     

Nanoparticle emission characteristics and reduction strategies by boost pressure control and injection strategies in a passenger diesel engine

This research attempted to analyze nanoparticles and other harmful exhaust emissions in accordance with injection strategies and air-fuel ratio (AFR) changes for small diesel engines. The emission characteristics were analyzed in the medium-speed condition, which is the main driving range of a diesel engine. In the case of particulate matter (PM), the number of particles was measured, analyzed, and compared to identify the correlation and emission characteristics of nanoparticles by using a dilution device and condensation particle counter (CPC), which are international standards for particle measurement recommended by the Particulate Measurement Programme (PMP). The engine torque tended to be reduced as pilot injections were added, and the torque was increased by the increased boost pressure, but reduced by the exhaust pressure increase in a part of the low-load range. The number of nanoparticles was not influenced greatly by the change in AFR, but the reduction effect on the PM weight was great depending on the boost pressure increase. In addition, the number of nanoparticles tended to increase as the fuel injection timing became closer to TDC in all conditions, and its difference became larger with an increase in AFR. In addition, in the case of the pilot injection, nanoparticle emission showed similar characteristics depending on the main injection timing, but it was increased by advanced injection timing when performing the main injection only, and the number of the nanoparticles increased as pilot injections were added. Last, the optimal conditions for EMS calibration were analyzed by selecting the conditions of torque reduction and NOx increase within 5 % from all of the engine operating conditions; optimized conditions are presented.     

低阻通风船体的远程控制测试平台开发（英文）

This paper addresses the development and testing of a remotely controlled boat platform with an innovative air-ventilated hull. The application of air cavities on the underside of ship hulls is a promising means for reducing hydrodynamic drag and pollutant emissions and increasing marine transportation efficiency. Despite this concept’s potential, design optimization and high-performance operation of novel air-cavity ships remain a challenging problem. Hull construction and sensor instrumentation of the model-scale air-cavity boat is described in the paper. The modular structure of the hull allows for easy modifications, and an electric propulsion unit enables self-propelled operation. The boat is controlled remotely via a radio transmission system. Results of initial tests are reported, including thrust, speed, and airflow rate in several loading conditions. The constructed platform can be used for optimizing air-cavity systems and testing other innovative hull designs. This system can be also developed into a high-performance unmanned boat.     

The structure of dissipation in the western Irish Sea front

We report on an intensive campaign in the summer of 2006 to observe turbulent energy dissipation in the vicinity of a tidal mixing front which separates well mixed and seasonally stratified regimes in the western Irish Sea. The rate of turbulent dissipation ε was observed on a section across the front by a combination of vertical profiles with the FLY dissipation profiler and horizontal profiles by shear sensors mounted on an AUV (Autosub). Mean flow conditions and stratification were obtained from a bed mounted ADCP and a vertical chain of thermistors on a mooring. During an Autosub mission of 60 h, the vehicle, moving at a speed of ~ 1.2 m s^− 1, completed 10 useable frontal crossings between end points which were allowed to move with the mean flow. The results were combined with parallel measurements of the vertical profile of ε which were made using FLY for periods of up to 13 h at positions along the Autosub track. The two data sets, which show a satisfactory degree of consistency, were combined to elucidate the space–time variation of dissipation in the frontal zone. Using harmonic analysis, the spatial structure of dissipation was separated from the strong time dependent signal at the M₄ tidal frequency to yield a picture of the cross-frontal distribution of energy dissipation. A complementary picture of the frontal velocity field was obtained from a moored ADCP and estimates of the mean velocity derived from the thermal wind using the observed density distribution. which indicated the presence of a strong (0.2 m s^− 1) jet-like flow in the high gradient region of the front. Under neap tidal conditions, mean dissipation varied across the section by 3 orders of magnitude exceeding 10^− 2 W m^− 3 near the seabed in the mixed regime and decreasing to 10^− 5 W m^− 3. in the strongly stratified interior regime. The spatial pattern of dissipation is consistent in general form with the predictions of models of tidal mixing and does not reflect any strong influence by the frontal jet.     

Impact of macrozoobenthic structures on near-bed sediment fluxes

Sandy sediments in shallow coastal waters of the Baltic Sea are often characterised by large numbers of biogenic structures which are produced by macrozoobenthos species. A series of experiments was devised to quantify how the interaction of such structures with the near-bed flow regime affects the sediment flux. Most experiments were done with simplified replicates of structures generated by typical species commonly found in the Mecklenburg Bight, starting with solitary structures and regularly-spaced arrays in a range of characteristic population densities, followed by a complex benthic macrofauna community, both artificial and alive. A laboratory flume channel, equipped with an acoustic Doppler flow sensor and a topography scanning laser, was used for high-resolution measurements (2 mm horizontal step size and 0.3 mm vertical resolution) of sand erosion (220 µm median grain size, at 20 cm s^− 1) and fine particle deposition (8 µm grain size, at 5 cm s^− 1). Sediment transport threshold values were measured for each layout. As a rule-of-thumb, both the erosion fluxes and the deposition of suspended matter increased considerably at low population densities (below 2%, expressed as percent of the sediment surface covered, i.e. roughness density RD). Above densities of 4%, erosion almost stopped inside the test arrays, and deposition remained well below the level of unpopulated areas. An attempt to extrapolate these findings to field conditions (using field current velocity data from 2001) showed that the net flux switched from erosion to deposition for densities above 5%. These parameters can now be integrated into a numerical sediment transport model coupling waves, currents, sediment dynamics and biological processes, which is currently under construction at the Baltic Sea Research Institute (IOW), Rostock, Germany.     

Egg production and associated losses of carbon, nitrogen and fatty acids from maternal biomass in Calanus finmarchicus before the spring bloom

We present concurrent data on ingestion, egg production and the loss of maternal biomass in pre-spring bloom female Calanus finmarchicus incubated under conditions representative of those in situ in the North Atlantic. A balanced metabolic budget was constructed and used to examine the relative importance of ingestion and biomass for fuelling egg production during the incubations. Ingested carbon was not sufficient to meet the observed demands for egg production. More than 80% of the carbon utilised by the females was instead derived from their biomass. Fatty acid analysis demonstrated that the storage reserves, 20:1 (n−9) and 22:1 (n−11), were virtually absent before experimentation began, and therefore could not have been used to supply the carbon required for egg production during the incubations. The C:N mass-specific ratio of the biomass utilised was 4.1, suggesting that the females had instead catabolised protein in order to meet their metabolic demands. These results suggest that C. finmarchicus adopts a sacrificial reproductive strategy when food availability is low.     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Model Test on Grouting Law in Dynamic Water-Rich Sand Layers by the Electric Resistance Method北大核心CSCD

In order to study the diffusion law of grouting slurry in the water-rich sand layer under flowing water conditions, a grouting test model consisting of a main test system, a grouting system, and a measurement system was developed. And for detecting the diffusion scope of the grouts, a new resistivity method was proposed. It is found that the relationship between grouting pressure and grouting rate during the test is strong. Under hydrodynamic conditions, the grouting slurry diffuses elliptically. Due to gravity and the effect of the upper water flow, the center of gravity of the ellipsoid is below the grouting outlet, and the grouting effectively improves the physical and mechanical properties of water-rich sand bodies. At the same time, the resistivity method has a good application effect on the detection of grouting diffusion range. The range of slurry diffusion obtained by the resistivity method is basically consistent with the boundary of the stone body after excavation, indicating that the resistivity method is reliable for detection of grouting range in dynamic water-rich sand layer. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Coastal Tourist Interest in Value-Added,Aquaculture-Based,Culinary Tourism Opportunities

Despite increasing focus on sustainable aquaculture investment in the U.S. coastal zones, the aquaculture industry continues to face skepticism among consumers due to perceived negative environmental impacts, and health and food safety concerns. Partnering with culinary tourism and local food promotion efforts has potential for improving public outreach about the benefits of aquaculture, especially in coastal destinations where sustainable marine aquaculture and tourism are both occurring. Culinary tourism implies that local foods reflect the local livelihood and culture, and may be important to the tourist's experience. Aquaculture is becoming increasingly valuable to coastal destinations for assuring the steady availability of local seafood to meet demand and retaining commercial fisheries as a means to differentiate themselves to tourists. This study examined the role of subjective knowledge and attitude about aquaculture, and their effect on intention to participate in value-added culinary aquaculture tourism experiences. The study found that tourists' subjective knowledge and attitude about aquaculture influenced intentions to participate in culinary aquaculture tourism. In order for farmers or tour operators to be successful in diversifying with value-added culinary aquaculture, attention needs to be paid to educating consumers, which may be possible through strategic partnerships with tourism organizations, chefs, and restaurants.     

A new approach for improving the performance of freight train timetabling of a single-track railway system

A new approach for improving the performance of freight train timetabling for single-track railways is proposed. Using the idea of a fixed-block signaling system, we develop a matrix representation to express the occupation of inter- and intra-station tracks by trains illustrating the train blocking time diagram in its entirety. Train departure times, dwell times, and unnecessary stopping are adjusted to reduce average train travel time and single train travel time. Conflicts between successive stations and within stations are identified and solved. A fuzzy logic system is further used to adjust the range of train departure times and checks are made to determine whether dwell times and time intervals can be adjusted for passenger and freight trains at congested stations to minimize train waiting times. By combining manual scheduling expertise with the fuzzy inference method, timetable efficiency is significantly improved and becomes more flexible.