A reduced-gravity model of the Catalan Sea

A reduced-gravity model is used to study the effects of the wind on the upper layer circulation in the Catalan Sea. The model parameters were set by observed features of the circulation in the basin. It is shown that the results are particularly sensitive to the open sea boundary conditions. Simulations were done using the following boundary fluxes: (i) mean values estimated by Bethoux (1980) and (ii) more recent geostrophic transports computed from hydrographic data by Font et al. (1988). The latter seem to lead to more realistic circulation patterns. The influence of seasonal winds (climatological data) on the dynamics is clear, especially during the winter.     

Improved customs inspection at a small international airport: Case study: Colombo

The present procedures for processing arriving passengers at the Colombo International Airport cause inordinte waiting times. An alternate plan, which is based on state of the art customs procedures, and which can reduce waiting times significantly while maintaining a high level of enforcement, is proposed. The present and proposed procedures are analyzed and compared with respect to passenger waiting times, using deterministic queueing theory. An optimal inspection rate of passengers by the customs service is proposed taking into account the fraction of inspected passengers, the waiting time of passengers and the cost of customs processing.     

Effect of Connecting the Front and Rear Air Suspensions of a Vehicle on the Transmissibility of Road Undulation Inputs

Airsprings have been used for vehicle suspensions over the last 40 years. They are mostly used as independent suspensions. Analysis of air springs available in literature is mostly limited to a single-degree-of-freedom system or a two-degrees-of-freedom system only in the translation mode. This paper deals with a model of a vehicle where the front and the rear springs are connected by a capillary tube. A two-degrees-of-freedom model having motion in bounce and pitch mode is presented. Equations of mass flow are linearized on the assumption of small variations in volume and pressure. Expressions for the transmissibility and the phase angle in the bounce and the pitch mode are derived. Road inputs to the front and the rear axles are assumed to be identical except for a phase difference between them. The effect of the capillary flow coefficient and that of the phase angle between the front and the rear axle excitation are studied. It is shown that an optimum value of the capillary flow coefficient exists which minimizes the transmissibility of motion in both modes over the entire frequency range. It is also observed that a phase angle of 180 degrees presents ideal transmissibility characteristics. Thus, a promising application of air springs for a vehicle suspension is presented.     

青藏线拉萨河特大桥主桥横梁设计

拉萨河特大桥主桥采用 (3 6+ 72 + 10 8+ 72 + 3 6)m五跨三拱连续梁钢管拱组合结构体系。通过对系杆拱桥不同部位横梁受力特点进行分析 ,采取相应的设计措施 ,为系杆拱桥的横梁设计提供一种合理的设计方法。     

Generation of cyclonic eddies in the Eastern Gotland Basin of the Baltic Sea following dense water inflows: numerical experiments

A sigma (σ)-coordinate ocean model by Blumberg and Mellor (POM) is applied to study the formation processes of mesoscale cyclones observed in the Eastern Gotland Basin following the dense water inflows. The initial conditions simulate a situation when the Arkona and Bornholm basins and partially the Slupsk Furrow are already filled with the inflow water of the North Sea origin, while the Eastern Gotland and Gdansk basins still contain the old water of pre-inflow stratification. Model runs with constant and time-dependent winds, changing the buoyancy forcing, grid geometry and bottom topography display the following. Entering the Eastern Gotland Basin from the Slupsk Furrow, the bottom intrusion of saline inflow water splits in two: one goes northeast towards the Gotland Deep, and second moves southeast towards the Gulf of Gdansk. An intensive mesoscale cyclonic eddy carrying the inflow water is generated just east of the Slupsk Furrow with the inflow pulse. A number of smaller cyclones with boluses of the inflow water are formed in the permanent halocline along the saline intrusion pathway to the Gotland Deep. Following Spall and Price [J. Phys. Oceanogr. 28 (1998) 1598], the cyclones are suggested to form by the adjustment of the high potential vorticity inflow water column to a low potential vorticity environment.     

Design and shared use of a terminal departure lounge for new large aircraft operations

New Large Aircraft (NLA) are new aircraft developments larger than any existing aircraft. The NLA's higher seat capacity will significantly impact passenger terminal design and operations. This paper focuses on the issues regarding the departure lounge. Deterministic queuing theory is used to determine the size and seating configuration of the lounge, as well as to decide whether a second level should be built to accommodate the increase in the number of passengers. The paper also discusses the use of the satellite section of a pier‐satellite terminal as a single lounge for the NLA. Spreadsheets are used to implement the analyses.     

Fatigue design for plug/ring type gas welded joints of sts301l including welding residual stresses

This paper presents a fatigue design method for plug and ring type gas welded joints, which incorporates welding residual stress effects. A non-linear finite element analysis (FEA) was first performed to simulate the gas welding process. The numerically predicted residual stresses of the gas welds were then compared to experimental results measured using a hole drilling method. In order to evaluate the fatigue strength of the plug and ring type gas welded joints, a stress amplitude (σ _a ) _R taling the welding residual stress of the gas weld into account was introduced and is based on a modified Goodman equation incorporating the effect of the residual stress. Using the stress amplitude (σ _a ) _R , the ΔP-N _f relations obtained from fatigue tests for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged into (σ _a ) _R -N _f relations. It was found that the proposed stress amplitude (σ _a ) _R could provide a systematic and reasonable fatigue design criterion for the plug and ring type gas welded joints.     

Ergonomic and biomechnical analysis of automotive general assembly using XML and digital human models

Automotive general assembly requires many manual assembly operations to be carried out by human workers. Ergonomic analysis is an important part of the design and evaluation of products, jobs, tools, machines and environments for safe, comfortable and effective human functioning. Most recent researches have involved the evaluation of working conditions to prevent work-related musculoskeletal disorders. The majority of previous research on automotive companies has mainly considered the results of ergonomic analyses such as RULA (Rapid Upper Limb Assessment), REBA (Rapid Entire Body Assessment) and OWAS (Ovako Working Posture Analysis System). Analysis of static posture including reachability, clearances for arm, hand and tool has also been used to evaluate working conditions. However, in addition to static posture analysis, a biomechanical analysis in dynamic conditions should also be conducted. There are no integrated frameworks or standard schema for ergonomic analysis using digital human models in digital environments. The purpose of this paper is to propose a new framework for the evaluation of working conditions by ergonomic and biomechanical analysis using digital models based on XML standard schema, including: products, processes, manufacturing resources and human workers. This paper presents the analysis results using the proposed framework for automotive general assembly operations. We propose a new framework for the evaluation of the assembly operations and their environments. Then we apply a digital human model to the dynamic simulation of general automotive assembly operations based on standard schemas in XML and PPRH (Product, Process, Resource and Human). Using PPRH information based on a standard XML schema to analyze the ergonomic and biomechanical results, the engineer can visualize, analyze and improve assembly operations and working environments in automotive general assembly shops using digital models.     

Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.