Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Development of a new sound metric for impact sound in a passenger car using the wavelet transform

Vehicles can experience impacts due to harsh road conditions. Contact with an uneven road surface causes vehicles to vibrate, which generates a loud impact sound. The attenuation of such noise is important because car passengers may complain about the impact noise. However, perfect removal of impact noise is not possible because most of it is caused by external conditions. More research is needed on the objective attributes of impact noise; however, the problem of impact noise is not a simple matter because impact noise is transient in nature and reaches a high level instantaneously. In this paper, a new objective attribute of impact noise is designed using the wavelet transform, which is appropriate for analyzing nonstationary signals, such as an impact signal. The usefulness of the new objective attribute, which is a sound metric, is examined by comparing the mean subjective ratings for real impact noise in passenger cars. The new sound metric has better correlation with the mean subjective rating than currently existing sound metrics.     

Design and optimization of an LPG roller vane pump for suppressing cavitation

A roller vane type liquefied petroleum gas (LPG) pump was developed for a liquid phase LPG injection (LPLi) engine. Most of the LPG pumps used in the current LPLi engines are installed inside of the LPG tank, but this pump is intended to be installed outside of the LPG tank to overcome the difficulty of fixing an in-tank pump. Because LPG has a low boiling point and high vapor pressure, it usually causes cavitation in the pump and consequently deteriorates the flow rate of the pump. The purpose of this work is to optimize the design of the roller vane pump in order to suppress cavitation and increase the fuel flow rate by using a computational fluid dynamics (CFD) analysis. In order to achieve these goals, the intake port configuration and the rotor of the roller vane pump were redesigned and simulated using STAR-CD code. Computation was performed for six different models to obtain the optimized design of the roller vane pump at a constant speed of 2600 rpm and a constant pressure difference between the inlet and outlet of 5 bar. The computation results show that an increased intake port cross-section area can suppress cavitation, and the pump can achieve a higher flow rate when the rotor configuration is changed to increase its chamber volume. When the inlet pressure difference is 0.1 bar higher than the fluid saturation pressure, the pump reaches its maximum flow rate.     

Computational and experimental investigation of the unsteady flow structures around automotive outside rear-view mirrors

The unsteady flow field around two automotive outside rear-view mirrors is investigated. This study includes comprehensive experimental and computational approaches in order to characterize the complex flow structures in the wake of the mirrors. The experiments were carried out in a wind tunnel which included the measurements of the instantaneous and averaged velocity fields as well as mean and unsteady surface pressure distributions. The simulations were performed using Large Eddy Simulation (LES). The LES approach (particularly with the dynamic subgrid viscosity model) provided good agreements with the experiments for the velocity and the surface pressure distributions. The experimental and the computational results of this study will be used as a benchmark to validate the current and the future CFD development and the subsequent aero-acoustic computations.     

Design and implementation of a UPnP-can gateway for automotive environments

In this paper, we propose a universal plug and play (UPnP) — controller area network (CAN) gateway system using UPnP middleware for interoperability between external smart devices and an in-vehicle network. The proposed gateway consists of a UPnP communication device, a CAN communication device, and a device translator layer. In-vehicle devices are not usually IP-based, so we implemented an in-vehicle device manager in the UPnP communication device which is in the gateway. We developed a vehicle simulator to produce real vehicular data for performance analysis. The CAN communication device transmits and receives real-time vehicle data between the real vehicular simulator and external devices through the UPnP. The device translator layer configures a message frame for enabling seamless data input and output between the CAN and UPnP protocols. After implementation, we generated an internal-external service request and tested the result. Finally, we confirmed the service request and operation between external devices and the internal vehicular device. Additionally, for a variety of external device numbers and communication environments, we demonstrated the gateway performance by measuring the round trip time (RTT) for overall service implementation.     

Experimental study on the impact characteristics of a sandwich composite with an aluminum foam core

The need for composites has been increasing in various industries because composites have good mechanical properties for their weight and superior stiffness and strength. The composites addressed in this study were multi-pore aluminum foam with a specific gravity of 1/10 composed of solid aluminum metal. This composite has excellent impact energy-absorption capability. In this study, impact tests on an aluminum foam core sandwich composite with a porous core were conducted to examine its mechanical properties. The specimen was a sandwich structure with an aluminum foam core, and different impact energies, such as 50J, 70J, and 100J, were applied to the specimen. Consequently, a maximum load of 5.5 kN occurred when the striker penetrated the upper face sheet in all experiments. The maximum load occurred at 4.2 ms for 50J, 3.5 ms for 70J, and 3.0 ms for 100J, indicating that the greater the impact energy was, the shorter the time was until the maximum load. After the maximum load occurred, that is, after the penetration of the upper face sheet, the striker penetrated 10 mm further, causing the core to be damaged in the 50J test, while the lower face sheet remained intact. In the 70J test, the striker penetrated the core and caused damage to the upper face sheet at 10 ms. Finally, in the 100J test, the striker penetrated both the upper face sheet and core and even the lower face sheet at 10 ms. Given the result above, the maximum load occurred when the striker penetrated the upper face sheet and the sandwich composite with aluminum foam core; the load then gradually decreased and then rapidly increased when the striker reached the lower face sheet, and the maximum load lasted slightly longer than the time required for the upper face sheet to be penetrated.     

Conceptual design of economic hybrid vehicle system using clutchless geared smart transmission

Most hybrid vehicles employ the continuously variable transmission (CVT or eCVT) currently as their choice of the transmissions. Recently, an automated geared transmission (AGT) or dual clutch transmission (DCT) is being tried for some hybrid vehicles for the better fuel economy than the CVT hybrid. However, this AGT or DCT is using automated clutches which require the hydraulic power in addition to the slippage in the clutch plate invoking some energy loss as well as wear. Also, they require a motor with significant power to match to the engine power. The clutchless geared smart transmission (CGST) has no clutch and the clutch function is performed by a planetary gear system controlled by a motor-generator. The hybrid vehicles proposed here using CGST may have some merits in durability, fuel efficiency, and cost since they do not have clutches. The motor used for the clutch function can be also working for power merge with the engine in propelling the vehicle. The proposed hybrid system can be either mild hybrid or full hybrid by adopting a different capacity of battery with much smaller motor-generator due to the planetary gear system compared to the other type hybrid vehicles. In this study, the prospects of newly proposed CGST hybrid system are examined in practical aspects compared with AGT hybrid or DCT hybrid systems.     

Operating speed pattern optimization of railway vehicles with differential evolution algorithm

The railway transportation system has much advantage in eco-friendliness, punctuality and safety compared to any other transportation system. Most of the railway system administrators have to control and operate under limited resources such as trains and facilities. It is necessary to control traveling time and energy consumption for efficient operation in the railway systems, because the board rate of passenger is inconstant with time variance. It is common that the shorter traveling time causes the greater energy consumption. In this study, a new optimization method considering operation time or energy consumption is proposed by using differential evolution algorithm and some cases are reviewed. The total energy change due to operation time variation are investigated by using the proposed optimization method for tangent and gradient track conditions. Both cases, the total energy decreases exponentially. However, because of gradient the total energy are saturated after a certain time for gradient track.