Fuel consumption of fuel cell hybrid vehicles considering battery SOC differences

Fuel cell hybrid vehicles (FCHVs) have become one of the most promising candidates for future transportation due to current energy supply problem and environmental problem. Fuel economy is an important factor in FCHVs. In order to properly evaluate the fuel economy of an FCHV, the initial battery state of charge (SOC) and the final battery SOC have to be identical so that the effect of the battery energy usage on the fuel economy is neglected. In the simulation or in the real driving, however, the final battery SOC is usually different from the initial battery SOC, and the final battery SOC often depends on the power management strategy. To consider the difference between the two battery SOC values, the concept of equivalent fuel consumption is presented by two methods. One is based on the relationship between delta SOC and delta fuel consumption, and the other is based on the optimal control theory. Two rule-based power management strategies for an FCHV are presented, and for each strategy, the fuel economy is evaluated based on the two methods. The characteristics of the two methods are discussed and compared, and the superior one is selected based on the comparison.     

FE modeling method for a headform used in pedestrian protection simulations

Finite element models of headforms are used in experimental simulations of pedestrian protection. In this study, a quick and accurate method for FE modeling of the headforms was developed. This method entailed the initial definition of the dimensional parameters for the mass, centroid, and inertial moment properties of the headform. The equations governing these properties were constructed using the dimensional parameters as design variables. The dimensional parameters meeting the requirements of the relevant regulations were obtained by solving these three equations. A design optimization model was constructed for the material parameters of the outer part of the headform. In this model, the parameters of the material used in the FE model were considered as design variables; the difference between the peak acceleration in a side-impact simulation test and the average value of the regulated acceleration range was used as the objective function; the first-order natural frequency, which was required to be greater than 5,000 Hz, was defined as one of the constraints; the peak drop acceleration, which was required to be within the regulated range of values, was defined as the second constraint. The material parameters were obtained by solving the optimization model. These material parameters meet the dynamic requirements of the regulations for headforms. Based on these three parameters, an FE model of a headform can be constructed quickly and accurately.     

Topology optimization of gas flow channel routes in an automotive fuel cell

An efficient topology optimization method for fluid-structure problems was developed in an effort to determine the optimum flow channel route in a fuel cell bipolar plate from first principles. This study describes the derivation and solution of new mathematical equations for topology optimization combining a density-based algorithm, the interpolation method of moving asymptotes (MMA), and the incompressible Navier-Stokes equation with a term representing the chemical reaction between hydrogen and the catalyst. The present method is based on the finite element method with a newly developed reaction rate equation. In this model, a topology variable of 0 represents viscous flow, whereas a value of 1 indicates porous flow. The flow velocity and pressure were obtained from the Navier-Stokes equation and constraints and element matrices for sensitivity analyses during the optimization. MMA was utilized to calculate the optimum flow routes in the design domain. The influence of the key design parameter q and the pressure drop on the optimum topology were also investigated. The channel topology became smoother with decreasing q, and the number of channels increased with increasing pressure drop.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Parameters Optimization for HEV Based on Simulated Annealing Particle Swarm Algorithm

分别采用多层次参数扫描(MLPS)算法和模拟退火粒子群优化(SAPSO)算法对并联式混合动力车逻辑门限控制策略的参数进行优化.将优化后的车辆以TEST-CITY-HWY测试循环进行仿真,并将结果与优化前的车辆的仿真结果进行对比.结果表明,经MLPS算法优化后,燃油消耗和HC与NOx排放分别下降了11.98％、6.01％和4.03％,但CO排放增加了25.18％;经SAPSO算法优化后,燃油消耗和HC、CO与NOx排放分别下降了13.61％、9.57％、27.78％和18.53％,且电池荷电状态(SOC)比MLPS优化略高.说明SAPSO算法在混合动力车控制参数优化效果上明显优于MLPS算法.     

Mixing over the steep side of the Cycladic Plateau in the Aegean Sea

Intensive microstructure sampling over the southern slope of the Cycladic Plateau found very weak mixing in the pycnocline, centered on a thin minimum of diapycnal diffusivity with Kρ=1.5×¹⁰−6 m² s^− 1. Below the pycnocline, Kρ increased exponentially in the bottom 200 m, reaching 1 × 10^− 4 m² s^− 1 a few meters above the bottom. Near-bottom mixing was most intense where the bottom slope equaled the characteristic slope of the semi-diurnal internal tide. This suggests internal wave scattering and/or generation at the bottom, a conclusion supported by near-bottom dissipation rates increasing following rising winds and with intensifying internal waves. Several pinnacles on the slope were local mixing hotspots. Signatures included a vertical line of strong mixing in a pinnacle's wake, an hydraulic jump or lee wave over a downstream side of the summit, and a ‘beam’ sloping upward at the near-inertial characteristic slope. Because dissipation rate averages were dominated by strong turbulence, ?/νN² > 100, the effect on Kρ of alternate mixing efficiencies proposed for this range of turbulent intensity is explored.     

Impact of phytoplankton community size on a linked global ocean optical and ecosystem model

We isolated the effect phytoplankton cell size has on varying remote sensing reflectance spectra (R_rs(λ)) in the presence of optically active constituents by using optical and radiative transfer models linked in an offline diagnostic calculation to a global biogeochemical/ecosystem/circulation model with explicit phytoplankton size classes. Two case studies were carried out, each with several scenarios to isolate the effects of chlorophyll concentration, phytoplankton cell size, and size-varying phytoplankton absorption on R_rs(λ). The goal of the study was to determine the relative contribution of phytoplankton cell size and chlorophyll to overall R_rs(λ) and to understand where a standard band ratio algorithm (OC4) may under/overestimate chlorophyll due to R_rs(λ) being significantly affected by phytoplankton size. Phytoplankton cell size was found to contribute secondarily to R_rs(λ) variability and to amplify or dampen the seasonal cycle in R_rs(λ), driven by chlorophyll. Size and chlorophyll were found to change in phase at low to mid-latitudes, but were anti-correlated or poorly correlated at high latitudes. Phytoplankton size effects increased model calculated R_rs(443) in the subtropical ocean during local spring through early fall months in both hemispheres and decreased R_rs(443) in the Northern Hemisphere high latitude regions during local summer to fall months. This study attempts to tease apart when/where variability about the OC4 relationship may be associated with cell size variability. The OC4 algorithm may underestimate [Chl] when the fraction of microplankton is elevated, which occurs in the model simulations during local spring/summer months at high latitudes in both hemispheres.     

URANS simulations of static and dynamic maneuvering for surface combatant: part 2. Analysis and validation for local flow characteristics

Part 2 of this two-part paper presents the analysis and validation results of local flow characteristics for a surface combatant Model 5415 bare hull under static and dynamic planar motion mechanism simulations. Unsteady Reynolds averaged Navier–Stokes (URANS) computations are carried out by a general-purpose URANS/detached eddy simulation research code CFDShip-Iowa Ver. 4. The objective of this research is to investigate the capability of the code in relation to the computational fluid dynamics-based maneuvering prediction method. In the current study, the ship is subjected to static drift, steady turn, pure sway and pure yaw motions at Froude number 0.28. The free surface, three dimensional vortical structure and, the validation of two dimensional local flow quantities together with the available experimental data are of the interest in the current study. Part 1 provides the verification and validation results of forces and moment coefficients, hydrodynamic derivatives, and reconstructions of forces and moment coefficients from resultant hydrodynamic derivatives.     

动力集中和动力分散的特点

从运用、市场和列车型式的发展趋势等方面 ,分析了动力集中和动力分散的特点。特别阐述了利用寿命周期成本 (L CC) ,来比较这 2种方式列车的优劣