Multi-response optimization of diesel engine performance parameters using thumba biodiesel-diesel blends by applying the Taguchi method and grey relational analysis

This paper presents an experimental study that involves an application of the Taguchi method and grey relational analysis to determine the optimum factor level to obtain optimum multiple-performance characteristics of a diesel engine run with different low-percentage thumba biodiesel-diesel blends. Four factors, namely, low-percentage thumba biodiesel-diesel blend, compression ratio, nozzle opening pressure and injection timing were each considered at three levels. An L₉ orthogonal array was used to collect data for various engine performance- and emission-related responses under different engine loads. The signal-to-noise (S/N) ratio and grey relational analysis were used for data analysis. The results of the study revealed that the combination of a blend consisting of 30% thumba biodiesel (B30), a compression ratio of 14, a nozzle opening pressure of 250 bar and an injection timing of 20° produces maximum multiple performance of a diesel engine with minimum multiple emissions from the engine.     

Model development and experimental research on an air spring with auxiliary reservoir

This paper focuses on the dynamic stiffness and overall equivalent damping of an air spring connected to an orifice and an auxiliary reservoir, with respect to the displacement excitation frequency, orifice area, and auxiliary reservoir volume. A theoretical model of this air spring with its auxiliary reservoir is derived by utilizing the energy conservation equation, gas state equation, and orifice flow rate equation. Simulation results from the presented model reveal that, when the air spring is subject to harmonic displacement excitation, its dynamic stiffness increases with an increase in excitation frequency and decrease in orifice area. Smaller orifice areas and lower excitation frequencies result in higher overall equivalent damping. A validation experiment is also implemented. When compared with experimental results, simulations show consistent varying trends of the dynamic stiffness and overall equivalent damping. The model developed here can correctly describe the behavior of the air spring with auxiliary reservoir, indicating that it is reasonable and feasible.     

Development of an idle speed engine model using in-cylinder pressure data and an idle speed controller for a small capacity port fuel injected SI engine

An idle speed engine model has been proposed and applied for the development of an idle speed controller for a 125 cc two wheeler spark ignition engine. The procedure uses the measured Indicated Mean Effective Pressure (IMEP) at different speeds at a constant fuel rate and throttle position obtained by varying the spark timing. At idling conditions, IMEP corresponds to the friction mean effective pressure. A retardation test was conducted to determine the moment of inertia of the engine. Using these data, a model for simulating the idle speed fluctuations, when there are unknown torque disturbances, was developed. This model was successfully applied to the development of a closed loop idle speed controller based on spark timing. The controller was then implemented on a dSPACE Micro Autobox on the actual engine. The Proportional Derivative Integral (PID) controller parameters obtained from the model were found to match fairly well with the experimental values, indicating the usefulness of the developed idle speed model. Finally, the optimized idle speed control algorithm was embedded in and successfully demonstrated with an in-house built, low cost engine management system (EMS) specifically designed for two-wheeler applications.     

Torque-based optimal vehicle speed control

This paper describes an optimal vehicle speed controller that uses torque-based control concepts. The controller design was divided into two steps: first, for a given vehicle speed trajectory, the engine torque demand was determined; in the second stage, a torque controller was implemented to track this torque demand. The torque demand was determined by a primary component and a correction component. The primary component was determined by solving an off-line optimization problem, and the correction component was added to compensate for the error caused by the off-line optimization. A modelbased proportional-integral (PI) feedback torque controller was employed to realize the engine torque tracking. Simulation results generated by a benchmark simulator were given to demonstrate performance of the optimal vehicle speed controller and a conventional PI speed controller that was included for comparison.     

Influential factors for HLA pump up in a roller finger follower engine

In an HLA (hydraulic lash adjuster) piston engine, “pump up” can occur when a valve is opened by the HLA when it should be closed. HLA pump up is more frequently encountered with exhaust valves than with intake valves. When HLA pump up in occurs in the exhaust valve, exhaust gas from the exhaust manifold enters the cylinder on the intake stroke, and fresh air-fuel mixture exits through the exhaust manifold on the compression stroke and is burned in the catalyst, causing partial burning, misfire, catalyst melting and power drop. HLA pump up occurs when the force on the valve from the HLA is higher than the force on the HLA from the valve. HLA pump up is related to design parameters, such as oil pressure, rocker ratio, spring load, spring surge, and both intake and exhaust valve timing. In this study, valve lift and load on a roller finger follower were measured at varying engine firing conditions to evaluate HLA pump up. The results indicated that effective measures to reduce HLA pump up include a higher rocker ratio, a lower oil supply pressure to the HLA, a higher spring installation load and a lower spring surge.     

Numerical and experimental investigation of lubricating oil flow in a gerotor pump

Gerotor pumps are widely used in the automotive industry for engine oil lubrication, due to their high volumetric efficiency and smooth pumping action. In many cases, the lubricating oil from the sump is mixed with contaminants, such as dust and tiny solid particles, or becomes thickened, due to aging. These problems will lead to critical situations, such as increased noise, enhanced wear and erosion, and poor lubrication of the engine. These critical situations were studied by conducting a detailed CFD integrated investigation on a gerotor pump’s performance at different operating conditions in three phases, and the results are presented in this paper. In first phase, a CFD model of a gerotor pump was developed with a dynamic mesh for the rotary movement of both the inner and outer rotors. The effects on pump flow rate of important parameters, such as rotor speed, fluid viscosity and number of ports, were simulated using non-contaminated oil at room temperature and an elevated temperature of 140oC. The relationship between flow rate and pressure at different rotor speeds was predicted and validated with test data for further parametric study. The pressure ripples at different time steps were measured at different angular positions of the rotors to examine the model accuracy. It was found that the flow rate increased and pressure pulsation, as well as flow recirculation, was reduced when ports were added to the cover plate. A suction pipe with a strainer was added for the second phase to capture the undesired changes in flow behavior, such as cavitation, which is caused by negative suction at the inlet region of pump. A suitable size for the inlet suction pipe for this pump was chosen after performing tests to characterize the flow behavior with single and double ports. Next, the relationship between pressure drop and strainer porosity was determined using different porosity values for the strainers. In the final phase, oil with different concentrations of solids was simulated to measure the effect of solid particles on flow rates and pressure losses. It was observed that the intensity of the recirculation was reduced at the suction end at the higher concentration of 0.04%, due to particle inertial effects. It was also found that particle size distribution affected the overall efficiency and pressure head of the pump.     

Breakup modeling of a liquid jet in cross flow

We propose a novel breakup model to simulate the catastrophic breakup regime in a supersonic cross flow. A developed model has been extended from an existing Kelvin-Helmholtz/Rayleigh-Taylor (K-H/R-T) hybrid model. A new mass reduction rate equation, which has critical effects on overall spray structure, is successfully adopted, and the breakup length, which is an important parameter in existing model, is replaced by the breakup initiation time. Measured data from the supersonic wind tunnel with a dimension of 762×152×127 mm was employed to validate the newly developed breakup model. A nonaerated injector with an orifice diameter of 0.5 mm is used to inject water into a supersonic flow prescribed by the momentum flux ratio of the liquid jet to free stream air, q ₀ . The conservation-element and solution-element (CE/SE) method, a novel numerical framework for the general conservation law, is applied to simulate the supersonic compressible flow. The spray penetration height and average droplet size along with a spray penetration axis are quantitatively compared with data. The shock train flow structures induced by the presence of a liquid jet are further discussed.     

Model referenced adaptive control to compensate slip-stick transition during clutch engagement

Clutches are widely used in various vehicle powertrains. The engagement process of a friction clutch has three phases, i.e., open, slipping, and sticking. Transitions between different phases introduce a discontinuity to the powertrain dynamics, which has been neglected in previous research. A model referenced adaptive controller (MRAC), based on Popov hyper-stability criterion, is designed to compensate the discontinuity. MRAC adjusts the frictional torque along with the errors of the state variables compared with those of a referenced model. The designed MRAC is applied to a clutch in a bus. Simulation and experimental results under fast and slow startup cases show that MRAC can simultaneously reduce vehicle jerk and frictional dissipation when compared with the conventional controller.     

预防性养护措施费用效益分析中的用户费用

根据运用费用效益分析的原理,对沥青路面预防性养护技术进行研究;总结了预防性养护技术的费用效益分析过程和方法,对费用效益分析中的业主费用和用户费用的计算方法、用户费用组成及其影响因素进行探讨.     

Sharing piping CAD models of ocean plants based on international standards

In the shipbuilding industry, different computer-aided design (CAD) systems are used for different design domains, structure, and outfitting. We need to exchange data among different CAD systems such as Tribon, AutoCAD, Intergraph or PDMS to complete the whole design and production process. There are two approaches to data exchange. One is direct translation; the other is indirect translation, which is based on a neutral format. If we use a neutral format, the data specification is open to the public and the design model can be used by other CAD systems, including next-generation CAD systems. In this paper, we propose an indirect method that uses ISO 10303 (STandard for the Exchange of Product model data) AP227 and ISO 15926 to define neutral formats. A separate ShapeDB is constructed to manage the geometry information, referenced to the catalogue data defined by ISO 15926. An experimental implementation for data exchange between Tribon and PDMS is described.