Fault diagnosis for wind turbine based on improved extreme learning machine

A fault diagnosis method based on improved extreme learning machine (IELM) is proposed to solve the weakness (weak generalization ability, low diagnostic rate) of traditional fault diagnosis with feedforward neural network algorithm. This method fuses signal feature vectors, extracts six parameters as the principal component analysis (PCA) variables, and calculates correlation coefficient matrix among the variables. The weight values of control parameters in the extreme learning model are dynamically adjusted according to the test samples’ constantly changing. Consequently, the weight fixed drawback in the original model can be remedied. A fault simulation experiment platform for wind turbine drive system is built, eight kinds of fault modes are diagnosed by the improved extreme learning model, and the result is compared with that of other machine learning methods. The experiment indicates that the method can enhance the accuracy and generalization ability of diagnosis, and increase the computing speed. It is convenient for engineering application.     

Gain and noise figure analysis of Er<Superscript>3+</Superscript>-doped YAG transparent ceramic microchip amplifier

The rate equations and the power evolution equations based on excited state absorption (ESA) and cooperative upconversion (CUC) of high concentration erbium-doped yttrium aluminum garnet (YAG) transparent ceramic waveguide amplifier are set up to analyze the effects of the pump power, active ion concentration and waveguide length on the amplifier gain and noise figure (NF). The numerical analysis predicts that with a pump power of 100mW, an active ion concentration of 1.0×10²⁶ ion/m³ and a waveguide length of 3 cm, a small-signal gain of 30 dB and an NF of 5 dB can be achieved in the micro-chip amplifier.     

Dynamics of inorganic nutrient species in the Bohai seawaters

Within the frame of a Sino-German Joint Research Program, two cruises of “R/V Dong Fang Hong 2” were carried out in September–October 1998 and April–May 1999, respectively, to understand the dynamics of nutrients in the Bohai. Nutrient species (NO₃⁻, NO₂⁻, NH₄⁺, PO₄³⁻ and SiO₃²⁻) are determined colorimetrically on board for five anchor and 30 grid stations. In situ incubation experiments are performed to determine planktonic nutrient uptake and benthic exchange flux. Nutrient concentrations display short-term variability and seasonal change in the Bohai, with higher levels in shallow coastal waters than in the Central Bohai. The influence of riverine discharge on nutrient levels can be seen from salinity isopleths, nutrient distribution and species ratios. Near-bottom (nb) waters have similar nutrient concentrations as to the surface waters in the Central Bohai, whereas stratification takes place in the Bohai Strait and North Yellow Sea. In situ incubation experiments provide evidence that the uptake ratio (i.e. N, P) by phytoplankton is proportional to the ratios among nutrient species in ambient waters. Based on the data of this study and previously publications, a preliminary estimate of nutrient budgets via riverine input and atmospheric deposition is established. The results indicate that atmospheric deposition gains importance over rivers in delivering nutrients into the Bohai and sustain the new production, following recent decrease in riverine inflow caused by drought periods in North China and damming practices. A historical review of nutrient data indicates that concentrations of nitrogen increase and phosphorus and silica decrease in the Central Bohai over last 40 years. This potentially has an important influence on the health of ecosystem in Bohai (e.g. food web and community structure), though further study is needed to examine the scenario in more detail.     

Study on dynamic characteristics of vehicle gearbox under multi-boundary conditions

With the development of vehicle gearbox to high-power-density and high-speed, how to predict and optimize the dynamic characteristics of vehicle gearbox becomes increasingly prominent. Aiming at the vehicle gearbox, this paper comprehensively and deeply studies the dynamic characteristics under the multi-boundary conditions. The generation mechanism of the multi-source excitations triggering the gearbox vibration is analyzed firstly. The vibration transfer path of the gearbox is explored. Secondly, the engine excitation, the gear meshing excitation and the bearing support load are numerically calculated. According to the finite element method, a fluid-solid coupling finite element model of the gearbox body is established to predict the gearbox dynamic responses based on the Galerkin method and the Hamiltonian variational principle. Finally, the effects of the excitation condition, oil height and reinforcement forms on the vibration responses of the gearbox body are thoroughly studied by simulation. The analysis indicates that it not only helps to modify and improve the method of forecasting the gearbox dynamic response, and also provides the theoretical and technical guidance for the gearbox design and optimization.     

Target priority determination methods by interval-valued intuitionistic fuzzy sets with unknown attribute weights

The paper aims at the problem of multi-targets threat degree being hard to be evaluated accurately in complex air defense battlefield environments. Combined with multi-sensors information fusion and interval-valued intuitionistic fuzzy sets (IVIFS) theories, the target priority determination is studied. The score and accuracy functions of IVIFS are improved with thinking about the hesitating information in order to increase the rationality. Then, the influence factors of target priority and the nonlinear relationship between the influence factors and target priority are analyzed. Next, the algorithms for calculating the factor weights and sensor weights are given. Based on the theory of IVIFS and technique for order preference by similarity to an ideal solution (TOPSIS), two methods of target priority determination based on the IVIFS and TOPSIS are proposed. At last, an application example verifies the effectiveness and flexibility of the proposed algorithms.     

Time Gap Modeling under Mixed Traffic Condition: A Statistical Analysis

This paper attempts to model vehicular time gap, which is defined as the time interval between any two successive arrivals of vehicles at a reference point of measurement on a road segment. Such an approach is justified under the non-lane-based heterogeneous traffic conditions prevailing in developing countries such as India, characterized by many “zero” time gaps due to simultaneous arrivals within a given road width. In addition, time gap data are characterized by a significant amount of data in the tail region due to long headways. Nevertheless, many researchers of time gap modeling have used light-tailed distributions that modeled time gaps satisfactorily due to two reasons: (a) The tail data was merged into a single bin; and (b) goodness-of-fit tests such as the Chi-square test, which has many limitations, were used. Further, some researchers have suggested different distributions for the same range of traffic flows, leading to ambiguity in distribution selection. In addition, bin size, which dictates the degree of fit of any distribution, has been ascribed very less importance in time gap modeling. Hence, this paper tries to consolidate and standardize the existing research in time gap modeling research by addressing all these issues. Two new distributions, namely Generalized Pareto (GP) and Generalized Extreme Value (GEV) with better tail modeling properties, have been proposed along with other conventional distribution to model vehicular time gaps over a wide range of flow from 550 vph to 4,100 vph. Two types of goodness-of-fit tests, namely Area-based and Distance-based tests, have been used. It has been found from the study that GP distribution fits the time gap data well (overall and tails) up to a flow range of 1,500 vph based on both kinds of tests, and GEV fits the data well for the flow levels above 1,500 vph based on the area test only.     

Tool for Predicting the Ultimate Bending Moment of Ship and Ship-Shaped Hull Girders

The present paper presents a historical review associated with the research works on hull girder strength of ship and ship-shaped structures. Then, a new program is developed to determine the ultimate vertical bending moment of hull girder by applying direct method, stress distribution method, and progressive collapse analysis method. Six ships and ship-shaped structures used in the benchmark study of International Ship and Offshore Structures Congress (ISSC) in 2012 are adopted as examples. The calculation results by applying the developed program are analyzed and compared with the existing results. Finally, the roles of the developed program and its further development are discussed.     

A Simplified Model for the Effect of Weld-Induced Residual Stresses on the Axial Ultimate Strength of Stiffened Plates

The present work investigates the compressive axial ultimate strength of fillet-welded steel-plated ship structures subjected to uniaxial compression, in which the residual stresses in the welded plates are calculated by a thermo-elasto-plastic finite element analysis that is used to fit an idealized model of residual stress distribution. The numerical results of ultimate strength based on the simplified model of residual stress show good agreement with those of various methods including the International Association of Classification Societies (IACS) Common Structural Rules (CSR), leading to the conclusion that the simplified model can be effectively used to represent the distribution of residual stresses in steel-plated structures in a wide range of engineering applications. It is concluded that the widths of the tension zones in the welded plates have a quasi-linear behavior with respect to the plate slenderness. The effect of residual stress on the axial strength of the stiffened plate is analyzed and discussed.     

Space enterprise strategy guiding-based study on project portfolio management and flow optimization

Project portfolio management (PPM) is the centralized management method, process and technology in multiple projects. When multiple projects in the space industry are implemented, it provides an effective methodology to resolve the problems at the same time such as conflicts among models, decrease in design efficiency, and increase in target deviation. Hence, a PPM dedicated to multiple projects management in space enterprise is presented in this paper. Firstly, an analysis of features and contents in space enterprise portfolio management mode is performed by using PPM based on its specific strategic characteristics. Then, the principle and selection methods of PPM are provided as a reference for the future development of an enterprise. Finally, a multiple-level organization architecture including decision making layers, function management layers and project execution layers is proposed so as to adapt to possible changes in the multiple projects and correspond to the strategic development. As a consequence, a perfect matching mechanism to fit the changes in PPM modes is reached. In addition, the flow chart of PPM is designed and optimized by analyzing the implementation procedure of strategic target and project portfolio life-cycle, which is expected to realize the purpose of improving space enterprise management efficiency, project management capacity, innovation development and economic benefits.     

Effect of interference fits on the fatigue lives of bolted composite joints

The effect of interference fits on the fatigue lives of bolted composite joints is investigated by conducting mechanical tests. Static and fatigue tests are carried out on specimens made of carbon-bismaleimide composites joined together as double-lap single-bolt joints. The bolts having interference fits ranging of 0 (neat fit), 0.5%, 0.75% and 1% are performed. The results demonstrate the relationship between fatigue life and different values of interference fits. After the fatigue tests, non-destructive evaluation (NDE) and scanning electron microscope (SEM) are used to observe the damage of the surrender and surface of the hole. The test results show that the interference fitted specimens have improved fatigue life compared to the neat fitted specimen. The NDE and SEM results reveal that the damage degree of interference fitted specimen is weaker than that for the neat fitted one.