Effects of the fuel injection ratio on the emission and combustion performances of the partially premixed charge compression ignition combustion engine applied with the split injection method

Currently, due to the severity of world-wide air pollution by substances emitted from vehicles, emission control is being enforced more strictly, and it is expected that the regulation requirements for emission will become even more severe. A new concept combustion technology that can reduce the Nitrogen oxides (NOx) and PM in relation to combustion is urgently required. As a core combustion technology among new combustion technologies for the next generation engine, the homogenous charge compression ignition (HCCI) is expanding its application range by adopting a multiple combustion mode, a catalyst, direct fuel injection and partially premixed charge compression ignition combustion using the split injection method. This paper used a split injection method in order to apply the partially premixed charge compression ignition combustion method without significantly altering engine specifications of the multiple combustion mode and practicality by referring to the results of studies on the HCCI engine. Furthermore, the effects of the ratio of the fuel injection amount on split injection are investigated. From the test results, the adequate combination of the ratio of the fuel injection amount for the split injection method has some benefit on exhaust and fuel economy performance in a naturally aspirated single cylinder diesel engine.     

Effect of operating parameters on diesel/propane dual fuel premixed compression ignition in a diesel engine

In this research, the effects of three operating parameters (Diesel injection timing, propane ratio, and exhaust gas recirculation (EGR) rates) in a diesel-propane dual fuel combustion were investigated. The characteristics of dual-fuel combustion were analyzed by engine parameters, such as emission levels (Nitrogen oxides (NO_x) and particulate matter (PM)), gross indicated thermal efficiency (GIE) and gross IMEP Coefficient of Variance (CoV). Based on the results, improving operating strategies of the four main operating points were conducted for dual-fuel PCCI combustion with restrictions on the emissions and the maximum pressure rise rate. The NOx emission was restricted to below 0.21 g/kWh in terms of the indicated specific NO_x (ISNO_x), PM was restricted to under 0.2 FSN, and the maximum pressure rise rate (MPRR) was restricted to 10 bar/deg. Dual-fuel PCI combustion can be available with low NO_x, PM emission and the maximum pressure rise rate in relatively low load condition. However, exceeding of PM and MPRR regulation was occurred in high load condition, therefore, design of optimal piston shape for early diesel injection and modification of hardware optimizing for dual-fuel combustion should be taken into consideration.     

Development of an electric active rollcontrol (ARC) algorithm for a SUV

Cornering maneuvers with reduced body roll and without loss in comfort are leading requirements for car manufacturers. An electric active roll control (ARC) system controls body roll angle with motor-driven actuators installed in the centers of the front and rear stabilizer bars. A vehicle analysis model developed using a CarSim S/W was validated using vehicle test data. Two ARC algorithms for a sports utility vehicle (SUV) were designed using a sliding-mode control algorithm based on a nonlinear roll model and an estimated lateral acceleration based on a linearized roll model. Co-simulation with the Matlab simulink controller model and the CarSim vehicle model were conducted to evaluate the performance of two ARC control algorithms. To validate the ARC performance in a real vehicle, vehicle tests were conducted at KATECH proving ground using a small SUV equipped with two ARC actuators, upper and lower controllers and a few subsystems. From the simulation and vehicle validation test results, the proposed ARC control algorithm for the developed ARC actuator prototypes improves the vehicle’s dynamic performance.     

Enhancement of aerodynamic performance through high pressure relief in the engine room for passenger car using cfd technique

High pressure acting on the vehicle’s body plays an important role in deciding the aerodynamic drag. An idea has been suggested to enhance the aerodynamic performance for small passenger car by relieving the high pressure in the engine room. The high pressure inside the engine room can be released to the outside of the vehicle through a hole perforated on the wheel house liner. About 1 % of the drag coefficient can be improved with the 1.88 % of the radiator air mass flow rate increment by installing the top hole with slots on the wheel house liner. Flow simulations are performed at the driving velocity of 110 km/h with the moving wall condition of the same velocity. The tire is rotating to catch more precise flow physics around a tire and wheelhouse liner.     

Cooling performance of 25 kW in-wheel motor for electric vehicles

The in-wheel motor used in electric vehicles was designed and constructed for an electric direct-drive traction system. It is difficult to connect cooling water piping to the in-wheel motor because the in-wheel motor is located within the wheel structure. In the air cooling structure for the in-wheel motor, an outer surface on the housing is provided with cooling grooves to increase the heat transfer area. In this study, we carried out the analysis on the fluid flow and thermal characteristics of the in-wheel motor for various motor speeds and heat generations. In order to resolve heat release, the analysis has been performed using conjugate heat transfer (conduction and convection). As a result, flow fields and temperature distribution inside the in-wheel motor were obtained for base speed condition (1250 rpm) and maximum speed condition (5000 rpm). The thermo-flow analysis of the in-wheel motor for vehicles was performed in consideration of ram air effect. Also, in order to improve cooling effect of the motor, we variously changed geometries of housing. Therefore, we confirmed the feasibility of the air cooling for the motors of 25 kW capacity with housing geometry having cooling grooves and investigated the cooling performance enhancement. We found that the cooling effect was most excellent, in case that cooling groove direction was same with air flow direction and arranged densely.     

Angular position error detection of variable reluctance resolver using simulation-based approach

The variable reluctance type resolver is widely used in an electric motor for hybrid electric vehicles as a rotor position sensor. The purpose of this paper is to present a simulation-based approach capable of determining a more accurate rotor shape of variable reluctance resolver in order to cut the time and cost of its development before testing a physical prototype. For the verification of the simulation-based approach to the position error detection of rotor, experiments for 8XVR resolver were conducted. Based on this approach, an optimal salient-pole rotor shape of 4X-VR resolver is proposed.     

Instantaneous 2-D visualization of spray combustion and flame luminosity of GTL and GTL-biodiesel fuel blend under quiescent ambient conditions

An experimental study has been performed on spray combustion and two-dimensional soot concentration in diesel (ULSD), GTL and GTL-biodiesel fuel jets under high-pressure, high-temperature quiescent conditions. Instantaneous images of the fuel jets were obtained with a high-speed camera. It was confirmed that by blending GTL with 20% rapeseed biodiesel, certain fuel properties such as kinematic viscosity, density, surface tension, volatility, lower heating value and others may be designed and improved to be more like those of conventional diesel fuel but with considerable decrease in the amount of sulfur, PAH, cold filter plugging point, etc. The results showed that the spray tip penetration increased and the spray cone angle decreased when 20% biodiesel fuel was added to GTL fuel. Autoignition of the GTL-biodiesel blend occurred slightly earlier than that of diesel fuel. Experiments under high-pressure, high-temperature conditions showed that higher injection pressure induced a lower soot formation rate. The integrated flame luminosity, which serves as an indicator of soot concentration in the fuel jet, was slightly higher for the GTL-biodiesel blend than for pure GTL fuel due to the slightly higher sulfur content of pure biodiesel fuel.     

Advanced hybrid energy storage system for mild hybrid electric vehicles

Hybrid electric vehicles (HEV) utilize electric power and a mechanical engine for propulsion; therefore, the performance of HEVs is directly influenced by the characteristics of the energy storage system (ESS). The ESS for an HEV generally requires high power performance, long cycle life, reliability and cost effectiveness; thus, a hybrid energy storage system (HESS) that combines different types of storage devices has been considered to fulfill both performance and cost requirements. To improve the operating efficiency and cycle life of a HESS, an advanced dynamic control regime in which pertinent storage devices in the HESS can be selectively operated based on their status is presented. Verification tests were performed to confirm the degree of improvement in energy efficiency. In this paper, an advanced HESS with a battery management system (BMS) that includes an optimal switching control function based on the estimated state of charge (SOC) is presented and verified.     

On-road assessment of in-vehicle driving workload for older drivers: Design guidelines for intelligent vehicles

There has been recent interest in intelligent vehicle technologies, such as advanced driver assistance systems (ADASs) or in-vehicle information systems (IVISs), that offer a significant enhancement of safety and convenience to drivers and passengers. However, the use of ADAS- and IVIS-based information devices may increase driver distraction and workload, which in turn can increase the chance of traffic accidents. The number of traffic accidents involving older drivers that are due to distraction, misjudgment, and delayed detection of danger, all of which are related to the drivers’ declining physical and cognitive capabilities, has increased. Because the death rate in traffic accidents is higher when older drivers are involved, finding ways to reduce the distraction and workload of older drivers is important. This paper generalizes driver information device operations and assesses the workload while driving by means of experiments involving 40 drivers in real cars under actual road conditions. Five driving tasks (manual only, manual primarily, visual only, visual primarily, and visual-manual) and three age groups (younger (20–29 years of age), middle-aged (40–49 years of age), and older (60–69 years of age)) were considered in investigating the effect of age-related workload difference. Data were collected from 40 drivers who drove in a real car under actual road conditions. The experimental results showed that age influences driver workload while performing in-vehicle tasks.     

On the feasibility of the optical steering wheel sensor: Modeling and control

This paper discusses the development of a system model for the wireless steering wheel angle sensor and steering wheel system for the evaluation of the steer by wire system in a vehicle dynamic system. The steering wheel sensor is a wireless, contact-less sensor utilizing an optical medium for angle detection. The optical medium is operated based on a photodiode and photo-detector head. A reflecting disc or code-wheel, working similar to a compact disc, is used to reflect the light from the photodiode back to the photo-detector. The beam is reflected based on the content in the reflective disc to measure the relative angle through a micro-controller. The proposed wireless steering sensor and steer by wire system is modeled using the Matlab/Simulink and their performance is investigated to evaluate the steering response, vehicle dynamics, and steering feel of the system. Finally, the feasibility of the proposed system is discussed based on the developed model and simulation results.