Effect of radial interference on torque capacity of press- and shrink-fit gears

Some gears in an automobile transmission have to be mounted by being press-fitted on a shaft instead of splines. The torque capacity of the press-fitted gear will be proportional to the radial interference. The excessive interference, however, will increase the gear radial deformation. In this paper, the press- and shrink-fit and the subsequent torque capacity test were investigated by finite element analysis, theoretically and experimentally. The static and dynamic coefficient of friction were determined.     

Loosening analysis for fastening screw of automotive door trim parts

While a screw is a fastening element that can tighten the two parts at low cost, the loosening of the screw is generated due to external forces such as repetitive load, vibration, and thermal stress. This phenomenon decreases the initial clamping force, and this can be a serious problem to the safety of the product. However, while fastening parts are handled through experiment and experience, there is a lack of research on the screw loosening of plastic fastening parts. For example, vehicles have various fastening parts. Among the fastening elements, screws are typically used for tightening parts of the vehicle door trim. Vehicle interior materials are mainly composed of plastic parts. Especially, the temperature of the vehicle interior changes from a sub-zero temperature to 100 degrees (°C) due to solar radiation. Unlike metals, plastic materials are commonly susceptible to the environment. In this study, the fastening screw of automotive door trim parts is selected. First, a screw loosening mechanism is implemented through Computer Aided Engineering (CAE) analysis and the influences of degradation are then analyzed. Secondly, the selecting method of clamping force is suggested through the analysis result of reduction according to the tightening torque.     

Automotive steering system preferences evaluated using a driving simulator

The automotive steering system is the primary channel through which road and vehicle behavior feedback is transmitted to the driver. While the driver provides directional platform control through the steering wheel, perceptions of the vehicle’s handling responsiveness are simultaneously transmitted back to the driver allowing for correction of any instabilities the vehicle may encounter. Based on these factors, drivers often pay special attention to the steering system when deciding what vehicle to purchase. Therefore, a significant amount of effort and time is invested in attempting to determine the optimal design of steering system components and configurations. In this study, the determination of an optimal steering configuration was attempted based on responses obtained from questionnaires that subjects answered. The questions were designed to evaluate the degree of satisfaction regarding the “control”, “ease of operation”, and “fun” participants experienced after each driving run. During the study, human subjects drove a driving simulator for 15 combinations of 3 different roadway environments and 5 different steering configurations, filling out a questionnaire after each scenario. The subjects were also classified as a type of driver (“utility”, “enthusiast”, and/or “performance”). The study attempted to determine if the mean values of questionnaire responses for “control”, “ease”, and “fun” type of questions changed as the scenario and/or driver type changed. Analysis of Variance (ANOVA) was used to determine if the mean values of the three types of questions were statistically different. The overall results suggest that the average responses for vehicle “control”, “ease”, and the “fun” type of questions were dependent on the type of roadway environment; however, only the responses for “fun” type of questions were influenced by the given steering configurations. Indeed, the steering system can impact the driver’s perceptions of the vehicle’s operational experience.     

Ground travel mode choices of air arrivals at regional destinations: The significance of tourism attributes and destination contexts

The aim of this paper is to examine the air leisure arrivals’ ground travel mode choice in the context of their decision to disperse beyond the gateway. A stated choice experiment was designed to examine the dispersal and travel mode choice of leisure visitors arriving on air transport at Cairns. Results show that for a hypothetical public bus alternative, attributes such as ‘sightseeing opportunities’ and ‘driver quality’ were significant for trips made to less known destinations located south of Cairns, compared to destinations north of Cairns. Findings suggest that while travel mode attributes and trip characteristics are significant determinants of the mode choice of air leisure arrivals, the extent of their significance varied markedly across destinations. Although the data examined in this paper were collected in Cairns, this research should be of relevance to many regions interested in understanding the relationship between destination transport and dispersal of air arrivals.     

IP MULTICAST GROUP MANAGEMENT FOR BROADCAST LANS DISTRIBUTION

IntroductionThere are two traditional types of communica-tion in computer networks:unicastand broadcast.A unicast address (one to one) is designed to sendmessages to a single destination in a network.Abroadcast (one to all) address is used to send datato the entire network(all hosts) .Multicast(oneor many to many) can be viewed either as an inter-mediate case,or as a generalized mode encompass-ing both unicast and broadcast as special cases.Inmulticast mode,messages are sent to an arbitraryse…     

预应力CFRP板加固钢梁抗弯疲劳试验研究

首先,采用修正的Pairs公式分析粘贴预应力CFRP板加固的钢构件的疲劳裂纹扩展行为.然后通过粘贴CFRP板的预制裂纹钢梁4点弯曲进行疲劳试验研究,最后基于阻止裂纹扩展的角度提出一种初步估计加固所需预应力大小的简化计算和设计方法.结果表明,粘贴预应力CFRP板对钢梁疲劳寿命的影响很大,与预制裂纹阶段比寿命提高最高可达10倍以上.不同的预制裂纹,同样的加固措施效果差别可达10倍.采用后张法施加预应力效果很好,锚固装置可以实时控制有效预应力,且预应力损失很小.     

Four-step travel demand model implementation for estimating traffic volumes on rural low-volume roads in Wyoming

This study develops a four-step travel demand model for estimating traffic volumes for low-volume roads in Wyoming. The study utilizes urban travel behavior parameters and processes modified to reflect the rural and low-volume nature of Wyoming local roads. The methodology disaggregates readily available census block data to create transportation analysis zones adequate for estimating traffic on low-volume rural roads. After building an initial model, the predicted and actual traffic volumes are compared to develop a calibration factor for adjusting trip rates. The adjusted model is verified by comparing estimated and actual traffic volumes for 100 roads. The R-square value from fitting predicted to actual traffic volumes is determined to be 74% whereas the Percent Root Mean Square Error is found to be 50.3%. The prediction accuracy for the four-step travel demand model is found to be better than a regression model developed in a previous study.     

Construction of Early Warning Control Platform for Tunnels and Subway Engineering北大核心CSCD

Based on an introduction to the construction and application of the early warning control platform for the tunnel and subway engineering, an overall analysis of the related data during tunnel and subway construction was conducted in order to give a better reference for the site construction, to guarantee safe and rapid qualified construc⁃tion, and to improve management efficiency. Based on red line control, deformation thresholds of surrounding rock, allowances of construction material and advanced geological prediction, a dual early warning system with automatic trigging and manual prejudging was adopted to control the quality of tunnels and subways and to guarantee safe con⁃ struction; through the platform a centralized management is realized, all the construction information and effective data are transmitted instantaneously by internet, decreasing management cost and increasing work efficiency. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Using satellite observations of ocean color to categorize the dispersal patterns of river-borne substances in the Gaoping (Kaoping) River, Shelf and Canyon system

Mapping the water constituents from remotely sensed ocean color data enables a better understanding of the dispersal patterns of river-borne substances in the Gaoping (formerly spelled Kaoping) River, Shelf and Canyon (KPRSC) system. Based on twelve MODIS-Aqua images in the KPRSC region taken in 2005, we apply a newly developed GA-SA approach to derive maps of chlorophyll-a concentration (Chl-a), colored dissolved organic matter (CDOM) and non-algal particle/detritus/mineral (NAP). The results demonstrated that the different characteristics of Chl-a, CDOM and NAP make them ideal tracers for observing large-scale dispersal patterns. With ancillary information of averaged daily precipitation, the daily wind field obtained from QuikSCAT (Quick Scatterometer), and the 8-day composite of the temperature field obtained from MODIS-Aqua, we categorized the surface dispersal patterns as coastal, northwestward and frontal patterns. Also, for the first time, we observed a sudden increase of biomass on a large scale from a pair of ocean color images taken over only a 2-day interval. Another remarkable feature is the interaction between the southeastward flow and the intrusion of the Kuroshio Branch, resulting in complicated patterns with various scales of vortex structures and current fronts. The observed features could be used for model validation of the flow field of the KPRSC system.