Effect of a drag-reducing polymer solution ejection on tip vortex cavitation

Experiments regarding the modification of the foil geometry and/or active or passive mass injection in the vortex core have been performed to investigate the possibility of inhibiting tip vortex cavitation. The ejection at very low flow rates of drag-reducing polymer solutions at the tip of hydrofoils and propeller blades has demonstrated effectiveness as a tip vortex cavitation inhibitor. This paper reports the results obtained with an elliptical hydrofoil, of 8cm maximum chord and 12cm haif-span, operating at Reynolds numbers, of =10⁶, much larger than those previously reported in the literature. Lift coefficients and critical cavitation numbers were determined for a variety of flow and polymer solution ejection conditions. Tangential and axial components of the mean velocity as well as velocity fluctuations along the vortex path were also measured. At 12.5 m/s free stream velocity and a variety of angles of attack, the ejection of a 500 ppm aqueous solution of a drag-reducing polymer at a flow rate of about 5 cm³/s leads to a decrease of up to 30% in the cavitation number. This occurs without modification of the lift coefficient and, hence, of the midspan bound circulation of the foil. Moreover, water injection does not cause any appreciable change in the cavitation numbers. The tangential velocity profiles along the vortex path during polymer ejection indicate that the potential region remains the same, while the viscous core dimension increases, and the maximum tangential velocity decreases substantially as compared to the no ejection or water ejection experiments. Thus, the pressure coefficients at the vortex axis are smaller than for the no ejection or water ejection cases and cause the reduction of the critical cavitation numbers. It is speculated that this inhibition effect is due only to swelling of the polymer solution when exiting the ejection orifice.List of symbols a core radius (distance to the vortex axis for maximum tangential velocity) - C ₁ lift coefficient - c _max maximum chord - Cp pressure coefficient at the vortex axis - Cp _min minimum pressure coefficient at the vortex axis - d _e diameter of the ejection port - m ejection flow rate - P reference pressure - P _v vapor pressure - V free stream velocity - V _a axial velocity - V _t tangential velocity - v _r radial component of the velocity resulting from jet swelling - x downstream distance from the tip of the foil - y, r distance to the vortex axis - angle of attack - r difference between the swollen jet and the ejection port radii - boundary layer thickness - tip vortex intensity - _d ( _de ) desinent cavitation number (with ejection) - _i ( _ie ) inception cavitation number (with ejection) - _ii normal stresses - viscosity - v kinematic viscosity - p specific mass     

An Extended Adaptive Kalman Filter for Real-time State Estimation of Vehicle Handling Dynamics

This paper considers a method for estimating vehicle handling dynamic states in real-time, using a reduced sensor set; the information is essential for vehicle handling stability control and is also valuable in chassis design evaluation. An extended (nonlinear) Kalman filter is designed to estimate the rapidly varying handling state vector. This employs a low order (4 DOF) handling model which is augmented to include adaptive states (cornering stiffnesses) to compensate for tyre force nonlinearities. The adaptation is driven by steer-induced variations in the longitudinal vehicle acceleration. The observer is compared with an equivalent linear, model-invariant Kalman filter. Both filters are designed and tested against data from a high order source model which simulates six degrees of freedom for the vehicle body, and employs a combined-slip Pacejka tyre model. A performance comparison is presented, which shows promising results for the extended filter, given a sensor set comprising three accelerometers only. The study also presents an insight into the effect of correlated error sources in this application, and it concludes with a discussion of the new observer's practical viability.     

������������������ϵͳģ��

电力是现今大部份铁道系统的动力来源． 可靠、有效率及安全的电力输送对整体铁道服务质素尤为重要，跟其它大型工程系统一样，铁道供电系统的设计，运作及筹划相当倚重计算机仿真．本文将回顾铁道供电系统仿真的模型及一般常规，并通过模拟结果例子及实际应用，介绍最新的模拟方式发展．本文亦对铁道供电系统仿真的未来挑战作出评论．     

REGULATED PHOSPHORYLATION OF THE GATA－2 DNA BINDINGPROTEIN IN ENDOTHELIAL CELLS

ＲＥＧＵＬＡＴＥＤＰＨＯＳＰＨＯＲＹＬＡＴＩＯＮＯＦＴＨＥＧＡＴＡ－２ＤＮＡＢＩＮＤＩＮＧＰＲＯＴＥＩＮＩＮＥＮＤＯＴＨＥＬＩＡＬＣＥＬＬＳＢｕＸｉｎＥ．Ｅ．Ｑｕｅｒｔｅｒｍｏｕｓ，Ｔ．Ｑｕｅｒｔｅｒｍｏｕｓ（ＤｅｐａｒｔｍｅｎｔｏｆＭｅｄｉｃｉｎｅ...     

Application of Aerodynamic Actuators to Improve Vehicle Handling

This exploratory study considers applications of active aerodynamic devices for suppressing parasitic motion and for improving the response of vehicles to steering, within the scope of the linear dynamic behaviour. A three DOF linear model is chosen to describe the side slip, yaw and roll motion of a baseline front-wheel steered vehicle. The improvements in performance of the base-line vehicle that are achievable by the application of direct yaw and roll moments are determined when either an open loop control pre-filter or a state feedback control law based on LQR design is applied. Unlike the former control, the state feedback control is unable to make the body side-slip angle vanish. The feedback control performance of each of the two moment actuators has been examined separately and then jointly. The advantages of combining the open loop and feedback dual actuator configurations are demonstrated using the two-degree of freedom control scheme. It is found that the scheme yields a spectacular performance but demands unreasonably large moments from the actuators in the context of available aerodynamic forces. On the other hand, the demand on direct yaw and roll moment of actuators is modest when the actuators are controlled using the LQR feedback only and if the control design is used to track a desired yaw rate trajectory and simultaneously to reduce the parasitic rolling motion. Significant improvements in handling and dynamic stability of a base-line vehicle can be achieved by aerodynamically generated direct yaw and roll actuator moments provided the target control performance is reasonable. The configurations of aerodynamic actuators considered are feasible for improving vehicle handling in cornering on motorways but more work remains to be done to explore alternative aerodynamic configurations that give rise to less side effects and higher lift coefficients.     

Optimizing the transportation of international container cargoes in Korea

This paper considers a multimodal transportation problem, which is the problem of determining the transportation flow, i.e. volume of container cargoes, and the transportation mode in each trade route, for the objective of minimizing the sum of shipping and inland transportation costs. The problem takes account of two restrictions: maximum cargo volumes capacitated at each seaport and maximum number of vehicles available at each transportation mode. To solve optimally the problem, this paper employs a mixed integer programming, which is an operations research technique. A case study is performed on the container cargo data in Korea and we draw several implications to improve efficiency in the transportation of international trade cargoes in Korea.     

Measurement of air–water CO2 transfer at four coastal sites using a chamber method

We measured the air–water CO₂ flux in four coastal regions (two coral reefs, one estuary, and one coastal brackish lake) using a chamber method, which has the highest spatial resolution of the methods available for measuring coastal air–water gas flux. Some of the measurements were considerably higher than expected from reported wind-dependent relationships. The average k₆₀₀ values for Shiraho Reef, Fukido Reef, Fukido River, and Lake Nakaumi were 1.5 ± 0.6, 3.2 ± 0.3, 0.69 ± 0.26, and 2.2 ± 0.9 (mean ± S.D.) times larger than the wind-dependent relationships. Results were compared with current-dependent relationships and vertical turbulence intensity (VTI). VTI is an index of water-surface stirring and is calculated from near-surface vertical velocity. Although some measurements from the reefs and river closely matched those expected from wind-dependent relationships, others were considerably higher. All data were correlated with VTI and were qualitatively explained by bottom macro-roughness enhancement. In Lake Nakaumi, results tended to differ from the wind-dependent relationships, and the difference between the measured and expected gas-transfer velocity was correlated with biological DO changes and/or the intensity of density stratification. We found these factors to have important effects on coastal gas flux. In addition, the chamber method was an effective tool for evaluating coastal gas flux.     

The combined effect of rain and wind on air–water gas exchange: A feasibility study

A series of experiments were conducted at University of Delaware's Air–Sea Interaction Laboratory to examine the combined effects of rain and wind on air–water gas exchange. During this study, ASIL WRX I, a combination of 3 rain rates and 4 wind speeds were used, for a total of 12 different environmental conditions. The SF₆ evasion method was used to determine the bulk gas transfer velocities, and airside profiles of wind and CO₂ were used to estimate flux–profiles of momentum and carbon dioxide. In addition to measurements of fluxes with and without rain in a wind–wave boundary layer, measurements of wave properties were also obtained. Rain is shown to alter the wind profile in the flume, and dampen surface waves. Also, SF₆ evasion indicates that with the present experimental setup, for most of the experimental conditions, rain and wind combine linearly to influence air–water gas exchange. Flux–profile relationships for marine atmospheric boundary layers, which were performed to scale up to field measurements, were explored by a comparison between SF₆-derived bulk fluxes and airside CO₂ profile measurements.     

Seasonal study of dissolved CH4, CO2 and N2O in a shallow tidal system of the bay of Cádiz (SW Spain)

During 2004, 10 samplings were performed in order to measure dissolved methane (CH₄), carbon dioxide (CO₂) and nitrous oxide (N₂O) in the surface waters of Río San Pedro, a tidal creek in the salt marsh area of the Bay of Cádiz (SW Spain). The inner partvs of the creek is affected by the inputs coming from an intensive fish farm and the drainage of an extensive salt marsh area.Dissolved CH₄, CO₂ and N₂O concentrations ranged from 11 to 88 nM, 36 to 108 μM and 14 to 50 nM, respectively. Surface waters were in all cases oversaturated with respect to the atmosphere, reaching values of up to 5000% for CH₄, 1240% for CO₂ and 840% for N₂O. Dissolved CH₄, CO₂ and N₂O showed a significant tidal and seasonal variability. Over a tidal cycle, concentrations were always highest during low tide, which points to the influence of the inputs from the fish farm effluent and the drainage of the adjacent salt marsh area, as well as in situ production within the system. Dissolved CH₄, CO₂ and N₂O seasonal patterns were similar and showed maximum concentrations in summer conditions. Using four different parameterizations to calculate the gas transfer coefficients [Liss, P.S. and Merlivat, L., 1986. Air-sea exchange rates: introduction and synthesis. In P. Buat-Ménard (Ed.), The Role of Air-Sea Exchanges in Geochemical Cycling. Reidel, Dordrecht, The Netherlands, p. 113–127.; Clark, J.F., Schlosser, P., Simpson, H.J., Stute, M., Wanninkhof, R., and Ho, D.T., 1995. Relationship between gas transfer velocities and wind speeds in the tidal Hudson River determined by the dual tracer technique. In: B. Jähne and E. Monahan (Eds.), Air-Water Gas Transfer: AEON Verlag and Studio, Hanau, Germany, pp. 785–800.; Carini, S., Weston, N., Hopkinson, G., Tucker, J., Giblin, A. and Vallino, J., 1996. Gas exchanges rates in the Parker River estuary, Massachusetts. Biol. Bull., 191: 333–334.; Kremer, J.N., Reischauer, A. and D'Avanzo, C., 2003. Estuary-specific variation in the air-water gas exchange coefficient for oxygen. Estuaries, 26: 829–836.], the averaged air–water fluxes of CH₄, CO₂ and N₂O from the creek to the atmosphere ranged between 34 and 150 μmol CH₄ m^− 2 day^− 1, 73 and 177 mmol CO₂ m^− 2 day^− 1 and 24 and 62 μmol N₂O m⁻² day⁻¹, respectively.     

Updating free speed models through mechanistic principles for Indian conditions

The prediction of free speeds of vehicles is an integral part of the economic appraisal of highways. It is to be noted that speeds not only govern the travel time costs, but also have major impacts on Vehicle Operating Costs (VOC). The World Bank has proposed a mechanistic free speed model based on the limiting speed concept for Highway Design and Maintenance (HDM)‐III. This model along with some refinements has been included in HDM‐4. The underlying assumption in the HDM free speed prediction model is that the free speed at any given point of time is the minimum of possible constraining speeds. This paper mainly addresses the methodology considered to update the free speed models through mechanistic principles (based on HDM‐4). This is accomplished by calibration of the model using the current data on free speeds, road and vehicle characteristics. Subsequently, the validation of the developed models has been carried out.