Estimation of road profile variability from measured vehicle responses

When assessing the statistical variability of fatigue loads acting throughout the life of a vehicle, the question of the variability of road roughness naturally arises, as both quantities are strongly related. For car manufacturers, gathering information on the environment in which vehicles evolve is a long and costly but necessary process to adapt their products to durability requirements. In the present paper, a data processing algorithm is proposed in order to estimate the road profiles covered by a given vehicle, from the dynamic responses measured on this vehicle. The algorithm based on Kalman filtering theory aims at solving a so-called inverse problem, in a stochastic framework. It is validated using experimental data obtained from simulations and real measurements. The proposed method is subsequently applied to extract valuable statistical information on road roughness from an existing load characterisation campaign carried out by Renault within one of its markets.     

Prediction of the dimensional deformation of the addendum and dedendum after the warm shrink fitting process using a correction coefficient

The warm shrink fitting process is generally used to assemble automobile transmission parts (shafts/gears). However, this process causes a deformation in the addendum and dedendum of the gear depending on the fitting interference and gear profile, and this deformation causes additional noise and vibration between the gears. To address these problems, the warm shrink fitting process is analyzed by considering the error in the dimensional deformation of the addendum and dedendum found when comparing the results of a theoretical analysis and finite element analysis (FEA). A correction coefficient that reduces this error is derived through an analysis of the difference in the cross-sectional area between the shapes used for the theoretical analysis and that of the actual gear, and a closed-form equation to predict the dimensional deformation of the addendum and dedendum is proposed. The FEA method is proposed to analyze the thermal-structural-thermal coupled field analysis of the warm shrink fitting process (heating-fitting-cooling process). To verify the closed-form equation using the correction coefficient, measurements are made of actual helical gears used in automobile transmissions. The results are in good agreement with those given by the closed-form equation.     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Comparative analysis of vehicle brake data in the ministry of transport test on the roller brake tester and on flat ground

This study performs a comparison between what occurs when braking on a Ministry of Transport (MOT) brake tester and on flat ground. The tire pressure is changed, but the other parameters remain constant. The results from this research and from the in-depth comparative study conducted by the mechanical engineering staff in the mechanical laboratory at the Miguel Hernández University in Elche have led to the following main conclusions: By varying the tire pressure, false results can be obtained with the MOT brake tester, which means that, if the tires are inflated at a low pressure but the brakes are in good condition, the vehicle will not pass the MOT. Conversely, if the brakes are in poor condition but the tire pressure is higher than what is recommended by the manufacturer, a false pass is produced. This article shows that the MOT brake testing equipment is often wrong and inexact, and the data and graphs presented prove that the tire pressure is a determining factor when assessing the condition of brakes.     

Topology optimization of gas flow channel routes in an automotive fuel cell

An efficient topology optimization method for fluid-structure problems was developed in an effort to determine the optimum flow channel route in a fuel cell bipolar plate from first principles. This study describes the derivation and solution of new mathematical equations for topology optimization combining a density-based algorithm, the interpolation method of moving asymptotes (MMA), and the incompressible Navier-Stokes equation with a term representing the chemical reaction between hydrogen and the catalyst. The present method is based on the finite element method with a newly developed reaction rate equation. In this model, a topology variable of 0 represents viscous flow, whereas a value of 1 indicates porous flow. The flow velocity and pressure were obtained from the Navier-Stokes equation and constraints and element matrices for sensitivity analyses during the optimization. MMA was utilized to calculate the optimum flow routes in the design domain. The influence of the key design parameter q and the pressure drop on the optimum topology were also investigated. The channel topology became smoother with decreasing q, and the number of channels increased with increasing pressure drop.     

Fuel consumption of fuel cell hybrid vehicles considering battery SOC differences

Fuel cell hybrid vehicles (FCHVs) have become one of the most promising candidates for future transportation due to current energy supply problem and environmental problem. Fuel economy is an important factor in FCHVs. In order to properly evaluate the fuel economy of an FCHV, the initial battery state of charge (SOC) and the final battery SOC have to be identical so that the effect of the battery energy usage on the fuel economy is neglected. In the simulation or in the real driving, however, the final battery SOC is usually different from the initial battery SOC, and the final battery SOC often depends on the power management strategy. To consider the difference between the two battery SOC values, the concept of equivalent fuel consumption is presented by two methods. One is based on the relationship between delta SOC and delta fuel consumption, and the other is based on the optimal control theory. Two rule-based power management strategies for an FCHV are presented, and for each strategy, the fuel economy is evaluated based on the two methods. The characteristics of the two methods are discussed and compared, and the superior one is selected based on the comparison.     

Improvement of exhaust gas pressure’s utilization for compressing the intake air in diesel engine’s cylinders

In order to improve the economical and environmental performances of the Diesel engines, the present paper aims to bring to the forefront solutions to increase the efficiency of the supercharging process carried out by the aggregates with Comprex type pressure waves. One solution to this is to drive the Comprex, not by the supercharged engine as it currently happens, but by a DC motor. The speed of the electric motor is modified, by means of an electronic management system, depending on the speed and load of the Diesel engine. The paper presents the experimental results obtained during the investigation of a supercharged Diesel engine by the Comprex driven type according to the proposed solution.     

Analysis process of a steering system using a concept model for idle vibration

This paper describes the development of an optimal design process for a steering column system and supporting system. A design guide is proposed at the initial concept stage of the development process to obtain sufficient stiffness of the steering system while reducing the idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, where vibration modes among the systems are separated by applying a vibration mode map at the initial stage of the design process. This study also provides design guidelines for an optimal dynamic damper system using a CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to the vehicle model to analyze the relation between the frequency and the sensitivity of the steering column system. This analysis methodology makes it possible to achieve target performance in the early design stage and reduction of damper tuning activity after the proto car test stage. Through the proposed steering column system development process, a lightweight vehicle with high stiffness is possible prior to the proto build stage. Furthermore, the improved process is expected to contribute to reducing the overall development period and the number of proto car tests necessary to achieve the desired steering system performance.     

Automotive structure vibration with component mode synthesis on a multi-level

The recursive component mode synthesis method (RCMS) has been implemented for the finite element analysis model of an automobile structure as an efficient free vibration analysis tool. The RCMS method is intended to obtain a better performance relative to the block Lanczos method, which is a traditional method in the industry of obtaining eigenvalues, while obtaining the acceptable accuracy. A numerical example of the automobile finite element model demonstrates the outstanding performance of RCMS compared to the block Lanczos method.     

A regional railroad network optimization model for coal transportation

A regional railroad network is presented to evaluate the system's response to increased coal traffic. An optimal, multimodal, coal-shipping pattern is developed for the study region to minimize total costs and to efficiently use the existing network. A two-stage, general model allocates resources among demands and then assigns flows to the network according to efficiency criteria. The model is sufficiently general to permit modification for specific needs, assumptions and data. Government agencies and industries can apply the model in resource allocation decisions and transportation policy analysis.