Application of slim A-pillar to improve driver’s field of vision

The importance of vehicle safety cannot be exaggerated in today’s mobile societies. Many manufacturers, associates related to vehicles and universities make an effort to improve vehicle safety by developing new technologies, applying high strength steel to the body structure etc. However, the majority of these efforts are focused on decreasing injury. It is absolutely important to minimize injury, but a more important aspect is coping with vehicle accidents. That is, As undeniably important as it is to minimize potential injuries, it is critical that experts focus on developing ways to keep drivers out of situations likely to lead to crashes in the first place. The purpose of this paper is to determine what the most critical factor is when coping with an unfamiliar driving situation. The answer is to provide a wide-open field of vision, especially for the driver. The driver’s field of vision is obstructed by the vehicle’s A-pillar. To solve this, the A-pillar obstruction angle, which is the angle between the driver’s eyes and the A-pillar should be decreased. This paper purposes three-methods for decreasing this angle structurally and applying a slim A-pillar which is as the best solution to decrease the A-pillar obstruction angle and ensure the drivers field of vision at the same time     

Development of electrostatic diesel particulate matter filtration systems combined with a metallic Flow-Through Filter and electrostatic methods

A 3000 cc diesel engine attached to an engine dynamo was used to test three newly developed electrostatic Diesel Particulate matter filtration Systems (DPS 1, 2, and 3) under four steady-state engine operating conditions: idle, 2000 rpm with no load, and 2000 rpm under 25% and 50% loads. Of the two developed alternatives, DPS 1 and DPS 2, DPS 2 comprises an ionization section, electrostatic field additional section and Flow-Through Filter (FTF), which achieved almost 90% removal of particulate matter (PM) under the engine’s operating conditions, and the efficiency of the FTF was maintained between 20% and 50%. Comparing the long-term performance of DPS 2 and DPS 3 (effectively a serial combination of two DPS 2s) with a commercially-available Diesel Particulate Filter (DPF), the DPS 2 and DPS 3 achieved almost the same efficiency for removing PM as the DPF but had significantly improved (75%∼90% lower) differential pressure drops.     

Parameter matchin and optimization for a hydraulic power-assistant system

A hydraulic power-assist system is a hydraulic regeneration system that can significantly improve fuel economy when installed on a conventional bus operating in urban traffic. This paper presents a methodology for matching a new hydraulic power-assist system (HPA) to a conventional bus. The HPA and the conventional bus were modeled using the AMESim environment. The HPA was optimized using a simulation-based orthogonal design method with two indexes, the fuel economy and the acceleration performance. According to the simulation results, the volume of the accumulator was the primary factor affecting fuel economy, and the gear ratio of the transfer case was the primary factor influencing the acceleration performance. As a result, tradeoffs between the two indexes are required for a practical operational scenario. Experimental results demonstrated that the optimal HPA installed on a conventional bus was able to satisfy the acceleration performance requirement of the vehicle and also reduced fuel consumption by 25 percent.     

Fault detection method for electric parking brake (EPB) systems with sensorless estimation using current ripples

A fault detection method with parity equations is proposed in this paper. Due to its low cost implementation, the velocity of the motor is not measurable in electric parking brake (EPB) systems. Therefore, residuals are not reliable when estimating the motor velocity with a low-resolution encoder. In this paper, we propose a fault detection method with sensorless estimation using current ripples that estimates the position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. In addition, this method can estimate the position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data, and the simulation results show that various faults have their own residual patterns. Therefore, we can detect the presence of faults by monitoring the residual signals.     

Experimental research of the EQ6110HEV hybrid electric bus using an on-line debugging system

This paper describes the on-line debugging software developed by our research team. The software has five functions and can be helpful in achieving rapid development for hybrid electric buses. In addition, the software can monitor system states continuously and also modify parametric maps or update control programs using its on-line programming function. Based on the on-line debugging system, the hybrid propulsion control system is designed, and all the working modes of the hybrid electric bus are tested. Finally, experiments are carried out that verify that the debugging system is feasible and reliable. The test results show that the hybrid electric bus can reduce fuel consumption by about 19.1 percent, in comparison with conventional buses.     

Design of power split transmission: Design of dual mode power split transmission

The power split type hybrid system transmits engine power by dividing it into the electrical unit and the mechanical unit. Its power transmission efficiency is highest at the mechanical point (MP), where the full power is transmitted to the mechanical unit. In this study, the equation for the MP was derived for the gear ratios of a general 4-node lever model. The MP characteristics for the transmission ratio (TR) of the input split and compound split structures were examined using the equation derived. Using the examined input split and compound split structures, a systematic design method for the dual mode power split transmission was proposed. In the dual mode power split transmission, the MP could be positioned at the desired TR, and the input split and compound split modes could be selectively used according to the clutch combination, which leads to the operation of the vehicle within a high system efficiency range.     

卵砾石层管推进工程超挖及卡钻对管材与土壤互制行为的影响研究

非明挖工法在都市施作时,常因困难地质(如卵砾石层)或障碍物而造成施工困难、工期延误或发生灾损。本文主要针对非明挖施工法里的管推进施工法(Pipe-jacking Method),探讨管推进工法施工时可能遭遇的困难,以及施工困难状况下之管材土体互制行为。探讨的施工困难包括超挖、挤压、卡钻等问题。本研究针对超挖范围、卡钻位置、阻力大小以及推进力施加位置等,以ABAQUS有限元素软件进行三维数值仿真,探讨直线推进施工中的问题。     

Conceptual design of economic hybrid vehicle system using clutchless geared smart transmission

Most hybrid vehicles employ the continuously variable transmission (CVT or eCVT) currently as their choice of the transmissions. Recently, an automated geared transmission (AGT) or dual clutch transmission (DCT) is being tried for some hybrid vehicles for the better fuel economy than the CVT hybrid. However, this AGT or DCT is using automated clutches which require the hydraulic power in addition to the slippage in the clutch plate invoking some energy loss as well as wear. Also, they require a motor with significant power to match to the engine power. The clutchless geared smart transmission (CGST) has no clutch and the clutch function is performed by a planetary gear system controlled by a motor-generator. The hybrid vehicles proposed here using CGST may have some merits in durability, fuel efficiency, and cost since they do not have clutches. The motor used for the clutch function can be also working for power merge with the engine in propelling the vehicle. The proposed hybrid system can be either mild hybrid or full hybrid by adopting a different capacity of battery with much smaller motor-generator due to the planetary gear system compared to the other type hybrid vehicles. In this study, the prospects of newly proposed CGST hybrid system are examined in practical aspects compared with AGT hybrid or DCT hybrid systems.     

Operating speed pattern optimization of railway vehicles with differential evolution algorithm

The railway transportation system has much advantage in eco-friendliness, punctuality and safety compared to any other transportation system. Most of the railway system administrators have to control and operate under limited resources such as trains and facilities. It is necessary to control traveling time and energy consumption for efficient operation in the railway systems, because the board rate of passenger is inconstant with time variance. It is common that the shorter traveling time causes the greater energy consumption. In this study, a new optimization method considering operation time or energy consumption is proposed by using differential evolution algorithm and some cases are reviewed. The total energy change due to operation time variation are investigated by using the proposed optimization method for tangent and gradient track conditions. Both cases, the total energy decreases exponentially. However, because of gradient the total energy are saturated after a certain time for gradient track.