CARD/1系统在互通立交设计绘图上的应用与开发

通过对CARD/1系统在T型（Y型）互通式立体交叉设计绘图上的二次开发，使T型（Y型）互通式立体交叉的设计绘图达到一体化。     

钢管拱吊装阶段中温度的影响分析

就缆索吊装钢管拱的施工方法，以工程实例讨论钢管拱在吊装阶段中温度对安装精度和应力测试结果的影响。     

用示波器对柴油机喷油系统进行故障检测与诊断

阐述利用示波器对柴油发动机喷油系统压力波形进行检测,并利用检测的压力波形对其故障进行诊断的基本原理和方法。     

钢管活性粉末混凝土轴压短柱受力性能试验研究

进行22根钢管活性粉末混凝土(钢管RPC)轴压短柱试验,分析其荷载-变形曲线、破坏特征和影响极限承载力的主要因素。试验研究表明:钢管RPC轴压短柱的荷载-纵向应变曲线弹性阶段约为极限荷载的90％~95％;套箍系数ξ较小时,在达到极限荷载后承载力急剧下降;ξ较大时,在达到极限荷载后承载力下降平缓并呈回升趋势。ξ较小的试件多呈剪切破坏形态;ξ较大的试件所有断面上均被墩粗,试件的上、下两端明显局部鼓曲。构件承载力随RPC强度fc的提高而提高,两者基本成线性关系;套箍系数ξ越大,构件承载力也越大,但钢管对RPC的约束效果比对普通混凝土的差。提出的钢管RPC轴压短柱极限承载力的实用计算公式计算出的结果与试验结果吻合良好。     

钢管-钢管混凝土复合拱桥实桥静载测试与分析

进行了第一座钢管 - 钢管混凝土复合拱试验桥--福建福鼎山前大桥实桥静载测试和有限元模拟分析,对钢管-钢管混凝土复合拱静力性能进行了讨论,研究表明,复合拱的静力性能与等截面拱相近,但拱肋变截面处应变应是设计中的控制因素,极限承载力分析应考虑双重非线性的影响.     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

南昌生米大桥总体设计

生米大桥是南昌市外环快速道上的城市桥梁，全长3880m，简要介绍生米大桥的项目概况、建设条件、总体布局、技术标准、技术特点、关键技术、科学研究等有关情况。     

Dynamic stride length adaptation according to utility and personal space

Pedestrians adjust both speed and stride length when they navigate difficult situations such as tight corners or dense crowds. They try to avoid collisions and to preserve their personal space. State-of-the-art pedestrian motion models automatically reduce speed in dense crowds simply because there is no space where the pedestrians could go. The stride length and its correct adaptation, however, are rarely considered. This leads to artefacts that impact macroscopic observation parameters such as densities in front of bottlenecks and, through this, flow. Hence modelling stride adaptation is important to increase the predictive power of pedestrian models. To achieve this we reformulate the problem as an optimisation problem on a disk around the pedestrian. Each pedestrian seeks the position that is most attractive in a sense of balanced goals between the search for targets, the need for individual space and the need to keep a distance from obstacles. The need for space is modelled according to findings from psychology defining zones around a person that, when invaded, cause unease. The result is a fully automatic adjustment that allows calibration through meaningful social parameters and that gives visually natural results with an excellent fit to measured experimental data.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

R/S分析法在盾构下穿机场过程中的地表变形规律研究

为保证机场的正常运营,在盾构下穿机场的施工过程中,对地表沉降变形控制的要求较高,因此对穿越过程中的施工控制和变形规律研究具有重要意义。首先,基于盾构下穿机场的工程条件,分析盾构下穿过程中的风险,并提出相应的控制措施;同时,根据现场监测数据,分析盾构下穿机场过程中的地表沉降变形规律,并利用R/S分析法对地表沉降的发展趋势进行研究。结果表明:盾构施工引起的机场地表变形均在控制值范围以内,且各监测点在不同序列条件下的Hurst指数均大于0.5,具有沉降持续减弱的趋势,验证下穿过程中风险控制措施的有效性,为类似下穿机场的盾构施工提供一定的实践经验,也为盾构施工引起的地表沉降变形规律研究提供参考。