802.lli与无线局域网安全

文章介绍了无线局域网（WLAN）802.11协议的安全性能缺陷,介绍了802.11i协议所提供的安全机制,并对802.11i协议的安全性和实用性进行了分析.     

三相永磁同步电机双闭环调速控制系统的设计——基于TMS320LF2407A和AT89C51

针对某装备中三相永磁同步电机调速的要求,采用TMS320LF2407A和AT89C51为核心设计了一电流、转速双闭环调速控制系统,给出了硬件原理图、关键器件、设计思想和程序流程图。实验结果表明该控制系统具有动态响应快、控制精度高、实时显示、数据存储、抗干扰强等优点。     

基于DSP的电磁式半主动吸振器控制器设计

以刚度可调的电磁式动力吸振器为控制对象,基于DSP设计了刚度随外界激励力变化而变化的半主动吸振系统,使吸振器始终工作于调协状态.从而拓宽了动力吸振技术的适用范围.硬件上以TMS320LF2407A信号处理芯片为核心,设计了I/O输入、模拟输入通道和驱动电路.由传统的模拟恒流方式改成了数字反馈,电路中不需要D/A转换和恒流源电路,在结构上简化了控制电路,使整个控制系统更加稳定、准确.     

Multi-modal traffic signal control with priority,signal actuation and coordination

Both coordinated-actuated signal control systems and signal priority control systems have been widely deployed for the last few decades. However, these two control systems are often conflicting with each due to different control objectives. This paper aims to address the conflicting issues between actuated-coordination and multi-modal priority control. Enabled by vehicle-to-infrastructure (v2i) communication in Connected Vehicle Systems, priority eligible vehicles, such as emergency vehicles, transit buses, commercial trucks, and pedestrians are able to send request for priority messages to a traffic signal controller when approaching a signalized intersection. It is likely that multiple vehicles and pedestrians will send requests such that there may be multiple active requests at the same time. A request-based mixed-integer linear program (MILP) is formulated that explicitly accommodate multiple priority requests from different modes of vehicles and pedestrians while simultaneously considering coordination and vehicle actuation. Signal coordination is achieved by integrating virtual coordination requests for priority in the formulation. A penalty is added to the objective function when the signal coordination is not fulfilled. This “soft” signal coordination allows the signal plan to adjust itself to serve multiple priority requests that may be from different modes. The priority-optimal signal timing is responsive to real-time actuations of non-priority demand by allowing phases to extend and gap out using traditional vehicle actuation logic. The proposed control method is compared with state-of-practice transit signal priority (TSP) both under the optimized signal timing plans using microscopic traffic simulation. The simulation experiments show that the proposed control model is able to reduce average bus delay, average pedestrian delay, and average passenger car delay, especially for highly congested condition with a high frequency of transit vehicle priority requests.     

SPECT颌骨静态显像对良恶性病变的鉴别诊断价值

应用SPECT(单光子发射计算机断层仪)对正常领骨30例和病人53例行SPECT颌骨静态显像,结果表明领骨良恶性肿瘤病变其SPECT静态像的核素浓集程度和方式、病变侧放射性计数(A)与健侧放射性计数(N)的比值(A/N)差异有高度显著性(P<0.005),病变范围大小同X线对照表明;当领骨肿瘤其SPECT静态图的病变范围明显大于X线显示的病变,则肿瘤的恶性可能性大。以上的结果为临床上对良恶性颌骨病变的鉴别提供了较重要的根据和定量筛选恶性病变的指标。     

RS-485/422标准的UART在DSP系统中的实现

TI公司的TMS320VC5416型DSP投有片上的通用异步串口（UART），若要在TMS320VC5416为CPU的系统中使用UART，必须另行设计。在分析TMS320VC5416的多通道同步缓冲串口（McBSP）与通用串口芯片MAX3140接口原理的基础上，提出了一种简单可行的高速通用异步串口（UART）设计方案，给出了其详细的软硬件设计资料，实践证明具有较高的工程应用价值。     

海缆无源探测数据采集系统的设计

针对海底光缆无源探测技术对数据采集的要求，采用了将TMS320VC5402的多通道缓冲串行口MCBSP配置为通用I／O串口与AD7714进行通信的方式，设计了一种由TMS320VC5402和AD7714组成的数据采集系统，对系统的整体结构、数据采集接口以及软件设计流程做了重要的阐述。     

基于DSP的单相阻抗测量仪设计

给出了一种基于DSP的单相阻抗测量仪设计方案.该测量仪可以在20～2 kHz频率范围内测量单相回路的阻抗.设计上选用高性能的DSP TMS320C6711作为处理器,充分利用其强大的运算能力和片内外资源并采用数字信号处理的方法,进行信号的信噪分离和矢量分解,使该测量仪具有高速,宽量程,测量准确的优点.文章介绍了测量仪的测量原理和设计方案,给出了硬件设计原理图和软件实现方法.     

IDENTIFICATION OF PHASE ERROR BY MULTI-SAMPLING DIGITAL TANLOCKED LOOP(MS-DTL)

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｍａｉｎｆｅａｔｕｒｅｏｆｔｈｅＣ－ＤＴＬｉｓｔｈａｔｉｔｈａｓａｐｈａｓｅｅｒｒｏｒｄｅｔｅｃｔｏｒｗｉｔｈｌｉｎｅａｒｃｈａｒａｃｔｅｒｉｓｔｉｃｓ，ｗｈｉｃｈｍｅａｎｓｔｈａｔｉｔｈａｓａｗｉｄｅｒｌｏｃｋ－ｉｎｒ...     

基于TMS320LF2407的六相异步电动机变频调速系统的设计

本文给出了基于TMS320LF2407的六相异步电动机变频调速系统的设计,包括IPM接口电路设计,控制电路的复位设计。设计了六相异步电动机的正弦脉宽调制的软件。通过对实验样机的测试,证明了该设计方案的有效性。