An inverse finite element method for the analysis of VIV data

This paper presents an algorithm for the frequency domain solution of dynamic linear “inverse” problems, that is for the processing of measurement data (strain, acceleration etc.) acquired on a mechanical structure, in order to estimate the loads acting on the structure and its corresponding response. The problem is formulated as a constrained (force equilibrium) optimization (small deviations from measurements, small loads) problem, which is transformed into an unconstrained problem, then into differential equations. The algorithm is applied to the estimation of hydrodynamic forces induced by the shedding of vortices from an offshore oil riser.     

地铁盾构隧道沿线障碍桩冲桩破除施工技术

通过西安地铁二号线盾构区间隧道穿越障碍桩的工程案例,对4种废弃障碍桩的处理工艺的优缺点进行对比,确定采用"基坑开挖+冲桩"的方法,并介绍冲桩施工的要点以及关键技术措施。采用的施工方案施工效果明显：工序简单、容易操作、工期短;工序相对安全,工艺可靠。所得以验可供今后类似工程借鉴参考。     

浅析G30线K3981～K3982路段防沙害处治方法

结合博乐公路管理局管养的G30线K3981～K3982路段路基边坡防沙害处治养护项目的实施,对处治沙害实施流程进行了详细的阐述,有一定的参考价值。     

液压转向系统冷启动沉故障机理及测试方法研究

液压转向系统冷启动沉故障在北方冬季是比较常见的一个故障,论文针对故障产生的机理进行了深入分析,并对产生故障的常见原因及改进方法进行了简单介绍,最后对如何确定故障源从测试方面提供了方法.     

Indirect method for wheel–rail force measurement and derailment evaluation

Wheel set flange derailment criteria for railway vehicles are derived and the influence of wheel–rail contact parameters is studied. An indirect method for wheel–rail force measurement based on these derailment evaluation criteria is proposed. Laboratory tests for the calibration of strain–force devices on the bearing box are carried out to determine the relationship between the applied force and the measured strain. The simulation package, SIMPACK, is used to develop a passenger car model to generate wheel–rail forces and vibration signals. Different cases are considered in this model to provide an accurate validation of the identified wheel–rail forces. A feasibility test is conducted in the Beijing Loop test line using a passenger car equipped with a set of strain gauges on the wheel set. The comparison of the force time history applied to the instrumented wheel set and that obtained using the indirect method is presented.     

汽车机械故障原因及防范措施

自中国改革开放以来我国的经济得到了飞速的提升,人们的生活质量和生活水平也在日新月异的变化,在现今时代汽车已经普及到了千家万户,成为了人们日常生活的必需品,也正因为如此汽车机械故障的原因及防范措施也逐渐受到了人们的关注,本文也就汽车故障产生的原因进行了分析,并寻找出相对应的解决策略.     

局部置换法在扶壁重力式码头倒滤井清理中的应用

扶壁重力式码头回填施工完成后,倒滤井残留砂的清理极为困难。以安哥拉罗安达第二石油服务基地及重件码头项目为工程依托,对局部置换法进行研究。该方法在回填砂和扶壁之间形成隔断层,阻断回填砂向倒滤井的流动,使得倒滤井残留砂的清理高效、彻底。     

重质液货晃荡载荷作用下薄膜型VLEC液货围护系统响应研究

随着美国页岩气中乙烷的大量出口,VLEC(超大型乙烷运输船)将成为新造船市场的热点,而薄膜型液货围护系统(CCS)的超大型乙烷运输船(VLEC)应该是大势所趋。高密度货物和大尺寸液舱造成了液货静压力和晃荡冲击压力的增加,提出了新的问题,VLEC液货围护系统的强度能否抵抗增加的晃荡冲击载荷。本文首先利用非线性有限元法计算分析液货围护系统在不同边界条件下的极限强度。然后运用CFD分析法对液舱晃荡问题进行数值分析,确定危险晃荡区域和晃荡载荷。最后对液货围护系统在液舱晃荡分析确定的危险工况进行响应分析,验证了围护系统的可靠性并归纳了一些重要结论。     

升压式开关直流调压器的不变性控制法

本文提出并分析了升压式开关直流调压器的一种不变性控制方法，它允许电源电压和负载电流在一定范围内变化而不影响输出电压值，而且该调压器的工作频率恒定。文中还给出了范例计算的结果。     

大跨度地下结构不同施工方法对围岩力学行为的影响

结合某工程，对断面在１００ｍ＾２以上的大跨度地下结构进行模型试验和有限元计算分析，探讨了不同施工方法引起周围介质的力学行为，提出了判断优化施工方法的依据。