搅拌桩处理公路软弱地基施工工艺的探讨

以搅拌桩工艺处理软土地基,使其承压性能达到道路施工的必要条件。基于工程实践对其使用工艺进行技术优化,对于提高作业效率和降低工程成本是十分必要的。     

Corrosion rate measurements in steel sheet pile walls in a marine environment

Corrosion of steel structures in the marine environment is a major problem. The deterioration of this kind of structures is costly and difficult to predict both when designing new structures and when estimating the remaining service life time for existing structures. The aim of this investigation was to find indicative values for the corrosion rate of steel sheet piles on the Swedish west coast. Such corrosion rates (mm/year) can be used both when designing new structures by oversizing the steel thickness and when estimating the bearing capacity of existing sheet pile structures. Earlier investigations on the corrosion rates along the Swedish east coast – with salinity from about 0.2% to 0.8% – are still used today as guidelines for the corrosion rate of all steel structures in the Swedish maritime environment even though the salinity on the west coast can be as high as 3.0%.Steel sheet pile wharfs located in the port of Halmstad on the Swedish west coast were inspected by ultrasonic measurements. Three wharf structures with a total length of about 700 m were inspected. None of the inspected wharfs had or have had cathodic protection. The thickness measurements of the steel sheet pile structures were performed by divers.The age of the three inspected sheet pile structures ranged from 36 to 51 years. The dimensions of the original sheet pile sections are known. One of the quay structures is located along a river. The salinity at all wharfs varied from low values at the surface to approx. 2% at the bottom (also in the river outflow).The measured average corrosion rates were in the same order as the design values in the European code. However, the results indicate increased corrosion rates about 1 m below the mean water surface and at the level of the propellers from the ships berthing the most frequented of the inspected wharfs, 3–6 m below water surface.The tolerances of steel sheet thicknesses – usually in the order of ±6% – are often neglected when investigating the remaining thickness in steel sheet piles. A simple calculation model shows that the sheet pile must be almost 50 years of age before an accurate estimation on the corrosion rate can be made, considering the tolerances, if the true original sheet pile thickness is not known.     

高铁湿陷性黄土隧道地基处理浅析

根据湿陷性黄土隧道工程特点,结合宝兰客专客运专线王家岔湿陷性黄土隧道地基加固处理的工程实例,阐述了洞口和洞内两种施工工艺不同的水泥土挤密桩施工方案,分析了隧道内水泥土挤密桩施工对其它工序的干扰和对工期的影响,以及施工振动对初支结构和围岩稳定的危害,提出了有效的控制措施.     

单向EMC层合板折叠变形时纤维微屈曲解

Francis等对单向形状记忆聚合物复合材料（EMC）层合板在热激活温度下的折叠变形过程建立了理论分析模型，研究结果表明：在板的整个弯曲过程都存在半波长，且其值恒定不变．实际上，小曲率条件下纤维的微屈曲还没有发生，半波长根本不存在．本文指出其研究中的不足并加以完善．结果表明：纤维微屈曲半波长与板的弯曲曲率之间的关系曲线可分为两个阶段，在小曲率阶段，因超出模型的适用范围被视为无效曲线；在大于小曲率的阶段，随着曲率的增加，半波长趋于稳定，同时该曲线能初步识别出模型的适用与非适用曲率范围．事实表明所提出的改进结果更加符合FMr屋全柏酌弯曲空际     

宿淮铁路(江苏段)桥梁设计技术创新

介绍宿淮铁路2座特大桥结构体系设计创新特点。理论计算分析表明:采用主跨132 m连续梁-拱组合体系单线桥可有效降低梁高,节省造价,施工和运营状态下,结构的强度、刚度、横向稳定、行车舒适度性等指标均满足规范要求;主跨108 m连续梁采用双向减隔震体系后,正常使用状态及多遇地震下结构正常工作。当设计地震及罕遇地震发生时,减隔震体系显著降低地震反应,避免了重要部位破坏,保证了桥梁结构的安全性,具有明显的经济效果。     

软土地基桥涵设计方法探析

软土地基是桥梁建设经常遇到的地基问题.针对软土地基的特点及桥梁在软土地基上的设计和建设的原则进行探讨,以期能为我国桥梁建设提供一些有意义的参考.     

原位反应制备从Al_2O_3颗粒增强铝基复合材料

利用差分扫描热分析研究了利用Ａｌ－Ｎｂ２Ｏ５系统制备Ａｌ２Ｏ３颗粒增强金属基复合材 料这的原位反应过程：用Ｘ－射线衍射分析了反应过程中的相变．实验结果表明，Ｎｂ 的还原和ＮｂＡｌ３金属间化合物的形成反应发生在Ａｌ的熔点以下；在９３９℃完成．在低温 下，试样的局部发生少量的原位反应；整个试样内部同时发生原位反应是在９３９℃放热峰 所覆盖的温度区间．最终显微组织中存在相同形态不同尺寸的ＮｂＡｌ３相．低温形成的 ＮｂＡｌ３相由于经历了长大过程而尺寸较大；高温形成的ＮｂＡｌ３相尺寸较小．     

高桥墩桩基础的优化设计及因素分析

在高桥墩桩基屈曲能量法分析的基础上,提出兼顾结构稳定、强度和经济性的优化模型,并应用优化算法中非线性序列二次规划法,进行优化设计探讨,同时给出优化设计算法流程图,编制了相应的优化计算程序;为了解桥墩高度、轴向荷载、地基比例系数和混凝土弹性模量对于高桥墩桩基屈曲的影响,结合优化设计模型进行了因素分析,探讨了参数变量对目标函数最优值的影响规律和程度,比较结果说明,在进行高桥墩桩基的屈曲受力分析时,高桥墩的大变形影响不容忽视;而一般在工程设计中,可考虑将桩周土体和混凝土弹性模量的增强作用作为设计的安全储备。     

填料性能对预应力锚拉式桩板墙影响的数值分析

预应力锚拉式桩板墙是一种得到广泛应用的新型支挡结构,本文通过建立耦合分析数值模型对桩板墙的受力特征进行了有限元分析。通过分析了解填料的力学参数(变形模量、摩擦角、粘聚力)对桩板墙位移、弯矩、土压力以及锚固端接触应力和自由段轴力的变化。揭示填料力学性能对预应力锚拉式桩板墙的影响,为类似工程的设计提供参考。     

真空堆载联合预压加固软基试验分析

根据真空堆载联合预压法加固路基的试验成果,对真空堆载联合预压法的规律性进行了分析,为软土基础的加固提供了依据。